• Korean Chemical Engineering Research
• /
• v.59 no.1
• /
• pp.1-5
• /
• 2021

The PEM(Proton Exchange Membrane)water electrolysis uses the same PEM electrolyte membrane as the PEM fuel cell and proceeds by the same reaction but the opposite direction. The PEM fuel cell has many methods of degradation analysis since many studies have been conducted on the degradation and durability of the membrane and catalyst. We examined whether PEM fuel cell durability evaluation method can be applied to PEM electrolytic durability evaluation. During the PEM electrolytic degradation process, LSV(Linear sweep voltammetry), CV(Cyclic voltammetry), Impedance, SEM(Scanning Electron Microscope) and FT-IR(Fourier Transform Infrared spectroscopy) were analyzed and compared under the same conditions as the PEM fuel cell. As the PEM fuel cell, hydrogen passing through the membrane was oxidized at the Pt/C electrode, and the hydrogen permeation current density was measured to analyze the degree of degradation of the PEM membrane. Electrode degradation could be analyzed by measuring the electrode active area (ECSA) by CV under hydrogen/nitrogen flowing conditions. While supplying hydrogen and air to the Pt/C electrode and the IrO2 electrode, the impedance of each electrode was measured to evaluate the durability of the electrode and membrane.

• Tribology and Lubricants
• /
• v.14 no.4
• /
• pp.108-113
• /
• 1998

In order to investigate the characteristics of top ring groove deposit formation in diesel engine, engine test and simulation test were performed. From component analysis of used oils sampled from actual running engines, soot content in engine oil was selected as a main parameter for evaluating oil degradation. Deposit formation is highly related to soot content in lubricating oils. And high soot content oil accelerates deposit formation even in low temperature region below 26$0^{\circ}C$. In low temperature region below 26$0^{\circ}C$, deposit formation rate is mainly affected by top ring groove temperature. However, in high temperature region above 26$0^{\circ}C$, deposit formation rate is affected by soot content as well as top ring groove temperature. Therefore, soot content as well as top ring groove temperature should be kept a certain level in order to prevent troubles due to carbon deposit formation.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.33-39
• /
• 1997

In order to establish a new temperature criterion to prevent the pistons from ring sticking due to deposit formation, bench test and engine test were performed. The effects of oil degradation and temperature on deposit formation was studied by a modified panel coking test. Oil degradation was analyzed by FTIR. Oil oxidation and nitration were selected as a factors to evaluate oil degradation. Bench test results show that oil oxidation is more effective to the deposit formation than oil nitration. And the temperature increase accelerates deposit formation and deposit formation increase rapidly above 26$0^{\circ}C$. Especially, in case of degraded oil, the deposit formation increases so rapidly that ring sticking can occur. The effect of piston temperature on the deposit formation was confirmed by engine test.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.715-716
• /
• 2008

변압기 절연 열화의 주원인 중 하나인 운전 온도에 대한 특성을 파악하는 것은 매우 중요하다. 본 논문에서는 IEC 60076 및 ANSI C 57.12 중 온도 상승 관한 시험 규격을 고찰하여 각 규격별 변압기의 구분 및 온도 상승 한도의 규격치를 비교 기술하였고, 모의부하의 인가 방법 중 등가 부하인가 방법, 오일 온도 및 평균 권선 온도의 측정시험 방법 등에 대하여 논하였다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.44-45
• /
• 2017

There are various national standards designed to test the physical properties of waterproofing materials for the respective countries based on each of their environmental parameters, variables and requirements. The problems of these standard systems can be outlined in the following: (1) there are too many test methods and criteria to satisfy in order assess one waterproofing membrane system, and (2) there is currently no known method to compile the separate testing results to provide a comprehensive report on waterproofing system durability. This paper outlines and compares the performance testing results of various types of asphalt waterproofing membrane systems and discusses the potentials of a complex environmental deterioration analysis method.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.343-346
• /
• 2008

To improve the reliability and extend the life for a wind-turbine gearbox, the gearbox needs to be monitored and analysed exactly. This study was conducted to analyze and detect the gearbox conditions when lubricating oil contaminated by wear particles was used. Characteristics of the gearbox failure by wear particles were monitored simultaneously by the on-line measurement sensor of vibration, oil condition and temperature. For the detail vibration analyses, frequency analysis(FFT) was performed. The results of the study were summarized as follows: Vibrational signal was found sensitive to abnormal changes of the gearbox conditions when lubricant was contaminated by wear particles. Also, using frequency analysis for the harmonics of gear mesh frequency(GMF), it is found that the failure of gearbox was caused by the damages of meshing gears. However, temperature and oil condition measuring signals were found not so effective to detect any gearbox failure by oil contamination.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.155-161
• /
• 2000

To improve the vehicle fuel economy, various technologies such as improvement of power train efficiency, use of light weight material, improvement of aerodynamic design, have been studied. One of the possible way to improve the vehicle fuel economy is to reduce the engine friction loss by improving the engine oil characteristics. In the present paper, it was examined the effect of the engine oil viscosity and the addition of friction modifier to engine oil on vehicle fuel economy improvements. Moreover, the effect of engine oil degradation on vehicle fuel economy was examined with two gasoline vehicles and one diesel vehicle by using the fuel economy test facility.

• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.168-176
• /
• 2014

This paper presents an engine oil change warning algorithm based on the test results of a small dip-stick-gage-type engine-oil-deterioration-detection sensor, software to realize the algorithm and a display device to apply the software. The algorithm determines the engine oil deterioration condition from the rate of change in the dielectric constant based on the average measured capacitance at $80^{\circ}C$ after the engine stops. The rate of change in the dielectric constant at the time for oil change correlates with the time that one of recommended warning limits for engine oil physical properties such as TAN (Total Acid Number), TBN (Total Base Number) and viscosity is first reached. At this point, a warning signal for oil change appears on the display device like a smart-phone or individual display device. The frames of smartphone app have three stages. The user can directly input all of the thresholds into the frame of the smartphone app. The screen of the display device comprises one frame for each warning signature with the related message. The user can input the thresholds to the device through a USB cable connected to a personal computer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.166-170
• /
• 2014

In this paper, we investigate the electric and magnetic properties of the engine oil, and estimate its changing time in transport truck. The four diesel trucks are selected, and the capacitance and inductance are investigated with parallel capacitor and induction coil, respectively. The measured capacitance gradually increases up to 10,000~14,000 km due to the activation of antioxidant, and then decreasing phenomena happen. The inductance decreases and the saturation began in 10,000~14,000 km range. Although the behavior of inductance is different from that of capacitance, but changing points are similar. From those results, we can estimate the changing time of engine oil is around 10,000~14,000 km and the inductance can be used for monitoring of engine oil in transport trucks.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.715-725
• /
• 2013

FAMEs produced from vegetable oil via transesterification reaction were known as alternative fuels. Lubrication and Wear properties of FAMEs were investigated to confirm the alternative possibility as lubricating base oil. In this study, lubrication properties and physical characteristics of mixture oils were examined using blended FAMEs(soybean, palm, waste oils) in two kinds of lubricating base oils. The oxidation stability of mixed samples were analyzed using ASTM D 2272 method and investigated for oxidation states of mixture oils after the shell four ball test. The results showed that the increase of FAMEs contents improved lubrication due to the intrinsic characteristics, however, increased the contents of oxidation which deteriorate the lubrication, and we found optimum mixture ratio as results of each base biodiesel (FAME).