• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.116.1-116.1
• /
• 2010

저급 연료원인 오일샌드는 아스팔트와 같은 중질유를 10% 이상 함유한 모래 또는 사암으로서, 겉으로는 시커먼 흙이나 모래처럼 보이나 내부에는 bitumen, 모래(점토) 및 물 등이 광물질 70~80%, bitumen 10~18%, 물 3~5% 정도의 비율로 혼합되어 있는데, 가열 또는 용매 추출 방식으로 오일샌드에 포함되어 있는 bitumen을 분리하여 정제하면 원유를 생산할 수 있으므로 고유가 시대의 대체에너지원으로 세계적인 석유회사들이 개발을 진행하고 있다. 따라서, 본 연구에서는 이러한 저급 연료원인 오일샌드 bitumen의 활용기술 개발을 위하여 기초특성 분석 결과 bitumen과 가장 유사한 특성을 가지는 것으로 파악된 중질잔사유를 대상으로 가스화를 통한 액체연료 전환을 위해 고점도 시료공급장치, 가스화기, 집진장치, 탈황장치, 수성가스 전환장치, 합성가스 압축장치, DME 전환장치 등으로 구성되는 시스템을 구축한 후 시험을 진행하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.108-115
• /
• 2004

Experiment and analytical studies on the oil supply characteristics of scroll compressor have been presented. For a scroll compressor, oil supply system consisting of individual lubricating element such as pumps, oil passages and sliding surfaces has been modeled by equivalent electric circuit. By solving the closed network equations of the model, oil flow rates at various lubrication elements could be obtained. Total amount of the oil flow rate drawn into the shaft has been measured and compared reasonably well with the prediction by the numerical simulation.

• Tribology and Lubricants
• /
• v.20 no.1
• /
• pp.27-32
• /
• 2004

This paper presents unsteady oil flow behaviors in the engine lubrication network to clarify the differences between continuous and discontinuous oil supply crankshaft system. Using commercial network analysis program, Flowmaster2, engine lubrication network system analysis were carried out. And effects of crankshaft speed and supplied oil pressure on pressure fluctuation in oil groove and oil flow rate to each bearing were analyzed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.95-103
• /
• 2019

Control systems of compressed gas supply facility are responsible for storing and supplying compressed gases required for launch complex qualification test and launch operation. Most of the facilities that make up the launch complex require compressed gas for their operation. Therefore, such control systems should be developed and verified earlier rather than the other systems that constitute the launch complex. Each verification for hardware and software is performed separately. In particular, software verification of control algorithms loaded on the controller takes a lot of time and man power during the development period of the control system. Thus, specific test procedures and methods should be prepared in advance for efficient development. This paper introduces the configuration of a compressed gas supply facility and its control system with the verification procedure and results of major algorithms.

• Journal of the Korean Institute of Gas
• /
• v.26 no.5
• /
• pp.1-9
• /
• 2022

Selection of a suitable artificial lift is important in terms of efficient operation and economics for oil production. In general, process of well design includes the selection of artificial lift, but the oil recovery could be enhanced by use of hybrid system combined with two types of artificial lift method according to reservoir condition for oil production. Electric submersible pump (ESP), as a presentative artificial lift method, is a manner for supplying the pressure in the lower part of oil well by using of a multi-stage centrifugal pump with an electric energy. However, there is a disadvantage that has a limit to the application period because of mechanical defection on ESP. Accordingly, it is possible to reduce the shutdown time of production well by applying the ESP/Gas lift hybrid system, which is to switch to a gas lift when an ESP is defective. This study describes the effect of ESP/gas lift hybrid system compared with ESP method for a onshore horizontal well locating in the of Permian basin, USA. As a result of study, ESP/gas lift hybrid system could make more effective productivity than ESP method. Also, we quantitatively predicted how much economic benefit would be obtained when the hybrid system was applied in the production well.

• Journal of the Korean Institute of Gas
• /
• v.26 no.6
• /
• pp.24-29
• /
• 2022

This paper is a purpose to Analyze and study the failure examples for a engine oil leakage of camshaft bearing seal, poor contact by computer connector fin damage and vaporizer inferiority on LPG automotive. The first example, when the researcher disassembled the cylinder head of engine to establish the cause for oil leakage, he confirmed the engine oil leakage by damaged between the engine intake camshaft bearing and seal part. The second example, the connector fin of power source line that control the starting of a car supplied with engine computer. As a result, it found the fact that the engine operation stopped because of cutting of the power source by connector fin damage. The third example, it verified the engine incongruity phe cutting of the power source by connector fin damage. The third example, it verified the engine incongruity phenomenon as thd gas didn't flow the vaporizer by foreign substance deposit. Finally, it supplied a small quantity gas from vaporizer to mix. As the computer controlling mix opening condition supplied a air as opening signal, the air and fuel became rarefied state. it knew that the engine didn't produce prpper power. Therefore, a car have to throughtly inspect not in order to arise the failure symptoms.

• Tribology and Lubricants
• /
• v.20 no.3
• /
• pp.119-124
• /
• 2004

Engine bearing system is generally affected by aeration. In this paper, the aeration effects on the engine crankshaft bearing system were studied. To do this, unsteady oil flow analysis on the engine crankshaft oil circuit system was carried out. And aeration effects on the bearing system were simulated to figure out lubrication characteristics of the each bearing such as oil flow rate, minimum oil film thickness, friction loss and increase of oil temperature.

• Journal of the Korean Institute of Gas
• /
• v.19 no.1
• /
• pp.12-17
• /
• 2015

The core of the CNG fueling station is the compressor and most of CNG compressors in Korea require lubrication. Lubrication oil of CNG compressor that can be transferred into the pressure regulators and the engines of fueling system can cause a negative effect on NGV(Nature Gas Vehicle) performance during refueling due to oil Carry-over. In order to avoid the problem, it is necessary to enhance the quality of the compressed natural gas by measuring quantitatively the amount of the transferred oil. In this research, a sampling device and sampling tube were developed, which can be used with a gravimetric method of detection to measure CNG oil Carry-over. In addition, CNG samples were taken at 6 pre-selected CNG fueling stations and analysed for their trace oil Carry-over. The measured total oil Carry-over ranged from 2.569 to 6.509 ppm. This test measurements were compared with those of previous studies to verify the results.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1643-1645
• /
• 2004

변압기는 판토그래프를 이용하여 가선으로부터 전력을 공급받아 전력변환장치, 견인전동기 등의 각종 장치에 필요한 전원을 공급해주는 중요한 역할을 한다. 또한 전장품에서 가장 무겁고 부피가 큰 변압기는 차량의 주행 속도에 큰 영향을 미치고 변압기를 설치할 수 있는 공간상의 제약이 따르므로 소형, 경량화가 매우 필수적이다. 본 논문에서는 변압기의 오일온도와 외함온도의 변화를 확인하기 위해 차량에 취부된 변압기에 온도 센서를 부착하였다. 또한 한국형 고속전철이 운행하는 동안 변압기의 온도가 기준 온도를 넘어갈 경우 차량의 치명적인 고장을 일으킬 수 있으므로 차량 내에 상시 계측시스템을 설치하여 변압기의 온도를 실시간으로 감시하고 측정하였다. 이를 통해서 변압기의 온도 변화와 열적 특성을 분석할 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.73-84
• /
• 2003

A transient analysis on fuel temperatures in an aircraft was studied using the finite difference method. Numerical calculation was performed by an explicit method of modified Dufort-Frankel scheme. Among various missions, close air support mission was considered with 20% hot day ambient condition in subsonic region. The aircraft was assumed to be in turbulent flow. The fuel system model with additional fuel supplies and return concept was considered. As a result of this analysis, the fuel tank temperatures have increased with the increase of the additional fuel supplies. In contrast to tank temperatures, the fuel temperature at the engine inlet has decreased with the increase of additional fuel supplies except in some in-flight phases having high engine fuel flow. From this analysis, the fuel system with the additional fuel supplies and return concept has been shown to be an effective method to decrease the engine inlet fuel temperature. Also, it has been shown that fuel flow rate through fuel/oil heat exchanger is a key factor influencing fuel temperature.