• 한국재난정보학회 논문집
• /
• 제13권2호
• /
• pp.147-154
• /
• 2017

듀플렉스 스테인리스강은 일반 오스테나이트계 스테인리스강과는 다른 열적, 기계적 성질로 인하여 일반 스테인리스강과는 다른 잔류응력 크기와 분포를 가진다. 따라서 듀플렉스 스테인리스강을 강구조물에 적용시키기 위해서는 용접부의 잔류응력 특성에 대한 연구가 반드시 선행되어야 한다. 본 연구에서는 듀플렉스 스테인리스강 용접시 발생하는 잔류응력을 스트레인 게이지를 이용한 응력 이완법을 이용하여 실험적으로 측정하여 용접부의 잔류응력 특징을 조사하였다.

• 열처리공학회지
• /
• 제24권5호
• /
• pp.271-276
• /
• 2011

The effect of grain size on the deformation induced martensite transformation and mechanical properties in austenitic stainless steel with high amount of Mn was studied. a'-martensite was formed by deformation and deformation induced martensite was formed with surface relief. With increase of grain size, volume fraction of deformation induced martensite was increased. With the increase in degree of cold rolling, hardness, and tensile strength was rapidly increased with linear relationship, while, elongation was decreased rapidly and then decreased slowly. With increase of grain size, hardness and tensile strength was rapidly increased with linear relationship, while elongation was decreased rapidly. The hardness, tensile strengths, and elongation were more strongly influenced by deformation induced martensite than the grain size.

• 대한금속재료학회지
• /
• 제50권6호
• /
• pp.413-418
• /
• 2012

This study was carried out to investigate the effect of reverse transformation on the mechanical properties in high manganese austenitic stainless steel. Over 95% of the austenite was transformed to deformation-induced martensite by 70% cold rolling. Reverse transformation became rapid above an annealing temperature of $550^{\circ}C$, but there was no significant transformation above $700^{\circ}C$. In addition, with an increasing annealing time at $700^{\circ}C$, reverse transformation was induced rapidly, but the transformation was almost completed at 10 min. There was a rapid decrese in strength and hardness with annealing at temperature above $550^{\circ}C$, while elongation increased rapidly above $600^{\circ}C$. At $700^{\circ}C$, hardness and strength decreased rapidly, and elongation increased steeply with an increasing reverse treatment time up to 10 min, whereas there were no significant change with a treatment time after 10 min. The reverse-transformed austenite showed an ultra-fine grain size less than $0.2{\mu}m$, which made it possible to strengthen the high manganese austenitic stainless steel.

• 소성∙가공
• /
• 제32권4호
• /
• pp.191-198
• /
• 2023

We examined the martensitic transformation kinetics for metastable stainless steel during electrochemical polishing (EP) using different types of electrolytes. Martensite fraction measured with EBSD showed that the electrolyte with high relative permittivity exhibited comparably higher levels of martensitic transformation. The amount of charge build-up on the specimen surface during EP with different types of electrolytes was calculated using COMSOL multiphysics simulations to understand these phase transformation characteristics. The effect of charge build-up-induced stress was analyzed using previously published first-principles calculations. We discovered that the electrolyte with high relative permittivity accumulated a greater amount of charge build-up, resulting in a stronger driving force for stress-induced martensitic transformation.

• 한국재료학회지
• /
• 제9권3호
• /
• pp.322-326
• /
• 1999

본 연구는 냉간가공과 열처리를 통해 Cu-26.65Zn-4.05Al-0.31Ti(wt%) 형상기억합금의 결정립을 미세화하기 위한 목적으로 수행하였다. 냉간가공을 위하여는 α-상이 가능한 많이 존재하는 (α+β)-조직을 가져야 하는데, 이는 550℃에서 열처리함으로써 얻었고, 최종두께 1mm로 냉간압연하였다. 총 압연율은 70%와 90%이었다. 냉간압연한 판재를 800℃에서 가열 후 급랭함으로써 형상기억특성을 갖는 상으로 변태시켰으며, 이 대 결정립크기를 측정한 결과, 열간압연한 경우보다 냉간압연과 열처리를 한 경우의 결정립이 월등히 작아졌음을 보여주었다. 냉간압연과 열처리를 한 경우에는 냉간압연 변형율이 큰 경우가 결정립이 더 작아지는 경향을 보였다. 또한 결정립크기가 작아짐에 따라 변태온도가 저하되었으며 오스테나이트상이 더 안정하게 되었음을 확인할 수 있었다. In this study, cold-rolling and appropriate annealing was adopted for the grain refining of Cu-26.65Zn-4. 05Al-0.31Ti(wt%) shape memory alloy. For the cold deformation of this alloy the ducti1e α-phase must be contained. After heat treatment at 550℃ the (α+β)-dual phase with 40vol.% α-phase was obtained which could be rolled at room temperature. This alloy was cold rolled into a final thickness of 1.0mm with total reduction degrees of 70% and 90%. The rolled sheets were betanized at 800℃ for various times, then quenched into ice water. The grain size of co]d rolled samples were 60∼80 ㎛ which is much smaller comparing with the hot-rolled samples. And the 90% rolled sample showed smaller grain size than the case of the 70% rolled one. The small grain size had influence on the phase transformation temperatures and stabilization of the austenitic phases.

• 대한조선학회논문집
• /
• 제45권5호
• /
• pp.530-537
• /
• 2008

Austenitic stainless steels(SUS 304, SUS 316), which are used for safety control valve of LNG carrier, are occasionally exposed in the cryogenic environment. In this regards, it is required to evaluate the mechanical characteristics under the low temperature environment. In this study, a series of uniaxial tensile test was carried out varying temperature for austenitic stainless steel. The phenomena of the strain-induced plasticity have been observed on the all temperature ranges. The critical value for threshold of 2nd hardening due to the phase transformation induced plasticity as well as the increase of hardening have been reported. The summarized experimental results would be used for the validation of numerical techniques applicable for the nonlinear hardening behavior of austenitic stainless steel under the cryogenic temperature environment.

• 한국재료학회지
• /
• 제8권7호
• /
• pp.648-652
• /
• 1998

자동차용 캠 샤프트의 표면경화를 위해 TiG 용접공정에 의한 재용융처리가 실시되었다. 재용융처리는 캠축에 평행한 방향으로 행하여졌다. 캠 샤프트 소재의 조직은 편상의 흑연과 퍼얼라이트의 회주철 조직으로 구성되어 있으나 재용융 처리후 미세한 퍼얼라이트 및 세멘타이트와 구상 오스테나이트의 레데브라이트 조직으로 변화하였다. 캠 샤프트 모재의경도는 HRc 25~28에서 재용융 처리후에는 HRg 53~55정도로 증가하였다. 다층 용융 처리시 비드가 겹치는 경계에서 검은띠가 관찰되었는데 이 검은띠는 흑연으로 판명되었다. 이 검은띠는 전층의 레데브라이트 조직이 변태된 것으로 주로 세멘타이트와 기지조직의 경계에서 생성되었다. 고밀도 에너지인 레이저 용융처리시에도 재흑연화 현상은 TIG의 경우처럼 관찰되었다. 재흑연화 현상의 확인을 위해서 Gleeble 1500을 이용하여 $1100^{\circ}C$와 $1000^{\circ}C$에서 0.5, 1, 3, 5 및 10초동안 유지한 모의실험을 하였다. $1000^{\circ}C$에서 0.5초 유지했을 때도 흑연이 발견된 것으로 보아 재흑연화 현상은 어떠한 재용융 처리 공정을 사용하더라도 피할 수 없는 현상임을 확인할 수 있다.