• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1A
• /
• pp.125-133
• /
• 2008

According to longer and longer span, dynamic instability of stay cable should be prevented. Dynamic instability occurs mainly symmetric 1st mode and antisymmetric 1st mode in stay cable. Especially symmetric 1st mode has a lot of influence on sag. Therefore fundamental frequency of stay cable is different from that of taut sting. Irvine, Triantafyllou, Ahn etc. analyzed dynamic behavior of taut cable with sag through analytical technical and their researches give important results for large bounds of Irvine parameter. But each research shows mutually different values out of characteristic (cross-over or mode-coupled) point and each solution of frequency equations of all researchers can be very difficultly found because of their very high non-linearity. Presented study focuses on fundamental frequency of stay cable. Generalized mechanical energy with symmetric 1st mode vibration shape satisfied boundary conditions is evolved by Rayleigh-Ritz method. It is possible to give linear analytic solution within characteristic point. Error by this approach shows only below 3% at characteristic point against existing researches. And taut cable don't exceed characteristic point. I.e. high accuracy, easy solving techniques, and a little bit limitations. Therefore presented study can be announced that it is good study ergonomically.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.24-29
• /
• 1998

An experimental study was carried out to investigate the characteristics of spray pattern such as discharge coefficient, spray angle, and mass distribution for two-fluid airblast swirl injector, within the range of fluid supply pressure 0~13kg/$\textrm{cm}^2$. In general atomization is promoted with increasing total gas mass flow and performance of the splay pattern was more stable when radial mass flow was greater than axial mass flow, radial swirler was better than Axial swirler for atomization. Equivalent spray angle did not change with water mass flow except for the condition of 3kg/$\textrm{cm}^2$ and showed the same for the gas mass flow. Mass distribution from the patternator shows that maximum value of the distribution were lowered but distributed larger area when gas flow rate increased. Center of mass position did not change with increasing water mass flow.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.5 s.305
• /
• pp.19-26
• /
• 2005

In this paper, a new method for obtaining three-dimensional shape of an object by measuring relative blur between images using wavelet analysis has been described. Most of the previous methods use inverse filtering to determine the measure of defocus. These methods suffer from some fundamental problems like inaccuracies in finding the frequency domain representation, windowing effects, and border effects. Besides these deficiencies, a filter, such as Laplacian of Gaussian, that produces an aggregate estimate of defocus for an unknown texture, can not lead to accurate depth estimates because of the non-stationary nature of images. We propose a new depth from defocus (DFD) method using wavelet analysis that is capable of performing both the local analysis and the windowing technique with variable-sized regions for non-stationary images with complex textural properties. We show that normalized image ratio of wavelet power by Parseval's theorem is closely related to blur parameter and depth. Experimental results have been presented demonstrating that our DFD method is faster in speed and gives more precise shape estimates than previous DFD techniques for both synthetic and real scenes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.310-316
• /
• 2016

We propose a novel contact-free transportation system in which an axial electrodynamic wheel is applied as an actuator. When the electrodynamic wheel is partially overlapped by a fixed conductive plate and rotates over it, three-axis magnetic forces are generated on the wheel. Among these forces, those in the gravitational direction and the lateral direction are inherently stable. Therefore, only the force in the longitudinal direction needs to be controlled to guarantee spatial stability of the wheel. The electrodynamic wheel consists of permanent magnets that are repeated and polarized periodically along the circumferential direction. The basic geometric configuration and the pole number of the wheel influence the stability margin of a transportation system, which would include several wheels. The overlap region between the wheel and the conductive plate is a dominant factor affecting the stiffness in the lateral direction. Therefore, sensitivity analysis for the major parameters of the wheel mechanism was performed using a finite element tool. The system was manufactured based on the obtained design values, and the passive stability of a moving object with the wheels was verified experimentally.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.59-59
• /
• 2011

파랑의 전파와 변형에 대한 연구에는 수심방향으로 적분한 2차원방정식인 완경사방정식과 Boussinesq 방정식을 기반으로 한 수치모형을 이용한 연구가 최근까지 가장 활발하게 진행되어 오고 있다. 그러나 실제 구조물의 설계에는 2차원 수치모형에서 고려할 수 없는 수심방향 유속에 기인한 정확도의 문제로 인해 구조물의 형상과 재원을 설계하기 위한 정교한 수치모형실험이 어려워 주로 수리모형실험에 의존해 왔다. 수리모형실험은 실제 현상을 가장 잘 재현해낼 수 있어 신뢰성이 매우 높지만 다양한 실험을 수행하기가 어렵고 많은 시간과 비용이 소요되는 단점이 있다. 이에 따라 최근 수심방향으로 완전한 운동방정식인 Navier-Stokes 방정식을 푸는 3차원 수치모형에 대한 연구가 활발히 진행되고 있다. 이론적으로 매우 우수한 모형이긴 하나 정확도 높은 결과를 얻기 위해서는 매우 조밀한 격자를 필요로 하기 때문에 아직까지 막대한 계산시간이 필요하다는 단점이 있으나 컴퓨터 기술이 급격한 속도로 발전하고 있어 Navier-Stokes 방정식 모형의 적용 가능성은 계속 높아지고 있다. 파랑변형을 다루는 수치모형실험을 수행할 때 외부조파를 사용할 경우 구조물이나 지형에 의해 반사되어 나온 파랑이 조파지점에 도달할 때 실험영역으로 재 반사되는 문제가 발생한다. 이를 해결하기 위해 내부조파기법의 개발에 대한 연구가 필수적이었으며, 자유수면변위를 변수로 사용하는 모형의 경우 그 연구가 매우 활발하게 진행되어 왔다. 한편, Navier-Stokes 방정식 모형의 경우 자유수면변위를 변수로 사용하는 2차원 모형에 비해 상대적으로 연구가 미흡하였다. 본 연구에서는 기존의 연직 2차원 Navier-Stokes 방정식 모형에 사용된 연속방정식에 질량 원천항을 추가하는 내부조파기법을 도입하여 3차원 수치모형에서 고립파를 내부조파하고, 급경사에서의 고립파의 처오름 및 처내림 현상을 수리모형 실험결과와 비교 및 분석하였다. 수치모형은 Navier-Stokes 방정식을 엇갈림 격자체계에서 계산하는 동수압 모형으로서, Two-step projection 기법을 사용하는 유한차분모형을 사용하였다. 본 수치모형은 난류의 해석을 위해서 상대적으로 큰 에디(eddy)만을 고려하는 SANS(spatially averaged Navier-Stokes) 방정식을 계산하는 LES(large-eddy-simulation) 기반의 수치모형으로, 난류 모델링을 위해 Smagorinsky LES 모형을 사용한다. 또한, 압력장의 계산을 위해 Bi-CGSTAB 기법을 이용하여 Poisson 방정식의 해를 구하였으며, 자유수면 추적을 위하여 2차 정확도의 VOF(volume-of-fluid) 기법을 사용하였다. 수치모형실험이 전체적으로 수리모형실험에서 관측한 파랑의 처오름 및 처내림 현상을 잘 재현하고 있는 것으로 나타났으며, 정량적인 비교를 통해 수치모형의 성능을 검증하였다.

• Journal of Korea Multimedia Society
• /
• v.10 no.8
• /
• pp.981-996
• /
• 2007

In this paper, we describe a method that can recognize gestures by obtaining motion features information with principal factor analysis from sequential gesture images. In the algorithm, firstly, a two dimensional silhouette region including human gesture is segmented and then geometric features are extracted from it. Here, global features information which is selected as some meaningful key feature effectively expressing gestures with principal factor analysis is used. Obtained motion history information representing time variation of gestures from extracted feature construct one gesture subspace. Finally, projected model feature value into the gesture space is transformed as specific state symbols by grouping algorithm to be use as input symbols of HMM and input gesture is recognized as one of the model gesture with high probability. Proposed method has achieved higher recognition rate than others using only shape information of human body as in an appearance-based method or extracting features intuitively from complicated gestures, because this algorithm constructs gesture models with feature factors that have high contribution rate using principal factor analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.5
• /
• pp.631-640
• /
• 2013

This paper provides a comparison of the J-integral estimation method under combined primary and secondary stress in the R6, RCC-MR A16 code. The comparisons of each code are based on finite element analysis using ABAQUS with regard to the crack shape, crack depth, and magnitude of secondary load. The estimate of the R6 code is conservative near $L_r=1$, and that of the RCC-MR A16 code is conservative near $L_r=0$. As a result, this paper proposes a modified method of J-integral estimation in the R6, RCC_MR A16 code. The J-integral using the modified method corresponds to the finite element analysis result.

• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.179-186
• /
• 1993

Heat pipes. applied to a flat plate solar collector, have a long and slender configuration with relatively low heat flux in the evaporator section. Such a heat pipe has a tendency to build-up a liquid pool at the lower part of the evaporator section. and at this pool occurs such complicated phenomena of evaporation and fluid dynamics as superheat, sudden generation of bubble, its likely explosive growth process and flooding, etc. In the present study. we tried to solve these problems by means of adjusting two principal design parameters, the liquid inventory and the installation region of the wick, using 4 heat pipes and 3 thermospheres. The corresponding results can be summarized as follows$\^$1)/. The effective thermal conductances of the heat pipe was greatly improved by eliminating the wick in the adiabatic and condenser sections$\^$2)/. The liquid inventory should be increased by about 40% larger than what is saturated the wick$\^$3)/. In the evaporator section the wick has a favorable effect to reduce both unstable operation by intermittent occurrence of nucleate boiling and response time at the initial start-up process.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.375-379
• /
• 2005

The morphology and therma]/viscoelastic characteristics were investigated for PLLA/MMT nanocomposite manufactured by incorporating inorganic nanosized silicate nanoplatelets into biodeuadable poly(l-lactic acid) (PLLA). The XRD difiactogram and TEM image may be regarded as a formation of homogeneously dispersed nanocomposites. The melting energy(${\Delta}H_m$) was increased during hydrolysis process because of increase of crystallinity. As MMT played a role of reinforcing agent, the storage modulus was increase in case of PLLA/MMT nanocomposite, it was well coincided with our previous results. From SEM image, many tiny pinholes formed by spinodal decomposition were observed on the surface, and the shape of nanocomposite was maintained during hydrolysis process. In this study, it was shown that the control of biodegradation rate, thermal/mechnical property was possibile by incorporating MMT.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1195-1203
• /
• 2012

Welding is a well-developed, widely used process for permanently joining metal components. However, the mechanical reliability of welded parts still offers room for improvement. A weld region consists of a fusion zone, a partially melted zone, and a heat-affected zone, and each zone has different material properties. In addition, the geometrical shape of a weld bead or fillet influences the mechanical reliability. A precise structural analysis must consider how a local welded region influences the mechanical behavior of the entire structure. This study focuses on an effective modeling scheme for the weld region. It relies on experimental and numerical methods to determine the proper correlation based on experimental results and to propose a modeling scheme for welded parts.