• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.3
• /
• pp.299-306
• /
• 2008

The electromagnet in Maglev vehicles controls the voltage in its winding to maintain the air gap, a clearance between the electromagnet and guideway, within an allowable deviation, with strongly interacting with the flexible guideway. Thus, the vibration characteristics of guideway plays important role in dynamics of Maglev vehicles using electromagnet as an active suspension system. The effects of the guideway's vibrational characteristics on dynamics of the Maglev vehicle UTM-01 are analyzed. The coupled equations of motion of the vehicle/guideway with 3 DOFs are derived. Eigenvalues are calculated and frequency response analysis is also performed for a clear understanding of the dynamic characteristics due to guideway vibration characteristics. To verify the results, tests of the urban Mgalev vehicle UTM-02 are carried out. It is recommended that the natural frequency of the guideway be minimized and its damping ratio in the Maglev vehicle with a 5-states feedback control law as a levitation control law.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1152-1160
• /
• 2007

In this paper we deal with a design of integral sliding mode controller to reject the disturbance force acting on the suspension system in the magnetically levitated system which is propelled by the linear induction motor. The control scheme comprises an integral controller which is designed for achieving zero steady-state error under step disturbances, and a sliding mode controller which is designed for enhancing robustness under plant uncertainties. A proper continuous design signal is introduced to overcome the chattering problem. The disturbance force produced by the linear motor is formularized by using a curve fitting of the experimental raw data. Computer simulations show the effectiveness of the designed integral sliding mode controller to reject the disturbance force.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7941-7948
• /
• 2015

Rolling noises during train operation are caused by vibration excited from irregularities of surface roughness between wheel and rail. Therefore, a proper measurement and analysis techniques of acoustic roughness between wheel and rail surface are required for transmission, prediction, and analysis of the train rolling noise. However, since current measuring devices and methods use trolley-based manual handling devices, the measurements induce unstable measuring speed and vibrational interface that increases errors and disturbances. In this paper, a new automatic rail surface exploring platform with a speed controller has been developed for improving measurement accuracy and reducing inconsistency of measurements. In addition, we propose a data integration method of the rail surface roughness with multiple homogeneous displacement sensors and verified the accuracy of the integrated data through standard test-bed railway track investigation.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.6-12
• /
• 2010

The source of wayside noise for the train are the aerodynamic noise, wheel/rail noise, and power unit noise. The major source of railway noise is the wheel/rail noise caused by the interaction between the wheels and rails. The Structure borne noise is mainly a low frequency problem. The train noise and vibration nearby the elevated railway make one specific issue. The microphone array method is used to search sound radiation characteristics of elevated structure to predict the noise propagation from an elevated railway. In this paper, the train noise and structure borne noise by train are measured. From the results, we investigated the effect on the sound absorption tunnel for elevated railway.

• Journal of the Korean Society for Railway
• /
• v.15 no.5
• /
• pp.436-441
• /
• 2012

Pressure waves are generated and propagate in tunnel when train enters a tunnel with high speed. Compression wave due to the entry of train head propagates along the tunnel and is reflected at tunnel exit as expansion wave. While expansion wave due to the entry of train tail propagates along the tunnel and is reflected at tunnel exit as compression wave. These pressure waves are repeatedly propagated and reflected at tunnel entrance and exit. Severe pressure change per second causes ear-discomfort for passengers in cabin and micro pressure wave around tunnel exit. It is necessary to analyze the transient pressure phenomena in tunnel qualitatively and quantitatively, because pressure change rate is considered as one of major design parameters for an optimal tunnel cross sectional area and the repeated fatigue force on car body. In this study, we developed the characteristics method analysis based on fixed mesh system and compared with the results of real train test. The results of simulation agreed with that of experiment.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.409-416
• /
• 2016

The contact force characteristic between the pantograph and the catenary wire represents the current collection quality of trains; it should be precisely controlled under international standard. Recently, a noise reduction cover has been installed around the pantograph of high speed trains. However, little study on the contact force by the pantograph cover has been conducted. In this study, the impact on the current collection performance of the pantograph cover was analyzed by dynamic contact force measurement using a next generation high speed train (HEMU-430X). As a result, it was confirmed that the attachment of a pantograph cover could lower the mean contact force by approximately 50N at 300km/h. In addition, the pure difference of the average contact force by the presence of pantograph cover, except for the static pressure, was measured and found to be up to 110N at 300km/h. It was also found that the standard deviation of the contact force of 3~5N could be changed by use of a pantograph cover.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.105-108
• /
• 2007

Recently, due to the high interests for well being life, claims about noise ad vibration are increased very rapidly. Therefore more reliable and exact evaluation of noise impact has been required. Until now in Korea, only one prediction equation for the assessment of railway environmental noise was used. But that equation has many limits and weak points because of the update was not performed from 1993. So in this study, the performance of another equation proposed by authors was compared to the former. As a result, proposed prediction equation may be used to evaluate the impact of railway noise in the future.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.763-766
• /
• 2006

The principal of a Maglev train is that floats on a magnetic field and is propelled by a linear induction motor. One of advantages is that it generates less noise compared to the wheel-on-rail train, because there are no wheels running along the rail. However, noises due to aero-dynamic disturbance and electrical system such as VVVF inverter and SLIM still occur. In this study, the Maglev cabin noises are measured during running and zero speed conditions. Pass-by noise measurements are performed to obtain outside noise during the operation of the train on the test tract. Data include a single microphone measurement as well as microphone array measurements. The array data are useful for sound source localization and more detailed noise reduction planning.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.849-854
• /
• 2001

Cabin noise reduction in maglev trains developed by KIMM is studied. Based on the measurements of cabin noise and acceleration levels during running and zero speed conditions, dominant noise sources are identified. After spectra characteristics of noise sources is investigated, efficient noise reducing methods are studied such as STL increasement of floor panels, sealing, and absorption treatment. It is found that the most important noise sources are VVVF inverter and SLIM in running condition. Since the noise sources are under the cabin floor, complete sealing and high STL of the floor panel are shown to be the most crucial factors in noise reduction. After polyurethan form (50t) is added for more sound absorption and sealing treatment, the cabin noise is reduced by 3-4 ㏈.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.603-608
• /
• 1998

In order to obtain basic data for the prediction of railway noise propagation, the noise radiation characteristics (source position, radiation directivity, etc) of trains were measured by using the sound intensity method. The measurements were performed at a side of railway by setting an intensity-probe array. As the measurement results, it was found that rolling noise due to interaction between wheel and rail and motor noise radiation from the lower part of train are dominant. The location of main sound sources can be described as being at the height of 0.1m in the center line of track, and the radiation directivity in the cross section of actually running trains are presented as a dipole source.