• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.2
• /
• pp.57-62
• /
• 2017

The heat transfer performance of a multi-heat-source fluidized bed heat exchanger was analyzed. The fluidized bed heat exchanger examined in this study can simultaneously recover the waste heat from gas, water vapor, and hot water. The effects of waste water flow rate, gas flow rate, and cooling water flow rate were examined to find their experimental correlations with the heat transfer coefficient. A computer program using the correlations was developed in this study to predict the thermal performance of the fluidized bed heat exchanger. The calculated heat transfer rates of gas, water vapor, waste water, and cooling water were compared with the measured values. It was found that the error of the calculated values was less than 12%.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.6
• /
• pp.257-262
• /
• 2014

This paper describes an experimental study for heating performance that can be used in R-134a automobile heat pump systems. The heat pump system is widely studied for heating system in zero-emission vehicles to attain both the small power consumption and the effective heating of the cabin. This paper presents the experimental results of the influence on heating capacity and coefficient of performance of heat pump system. Tests were performed with different sizes of internal and external heat exchangers, and refrigerant flow rate was also considered in two-way flow devices. In addition, the heat, air, and water sources with the heat pump system were examined. The experimental results with the heat pump system were used to analyze the impact on performances. The best combination of performance was A-inside heat exchanger, B-outside heat exchanger, and B-flow device, respectively. In addition, a water heat-source was found to give roughly 40% of better performance than an air heat-source heat pump system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.80-85
• /
• 2003

Recently, induction heating cooker(IH-Cooker) is very interested for high efficiency, the quickness of heating time and the convenient regulation of heating spot. In this paper, we proposed the magneto-thermal analysis of an induction heating cooker(IH-Cooker) as an efficient design, and analyzed the magnetic fold intensity inside the axisymmetric shaped cooker using three-dimensional axisymmetric finite element method(Flux2D) and the effectual heat source was obtained by ohmic losses from eddy currents induced in the cooker. Also, we presented the temperature characteristics of the IH-Cooker according to input frequency and relative permeability in stainless parts and in aluminum parts.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.506-511
• /
• 2006

To today with the acceleration due to the preference actual condition of high-class energy national income level it is together improving. It follows hereupon and it is convenient and the neat heat source is increasing a tendency where it is. It investigates the government offices building in commerce portion from the research which it sees and from the draft it analyzes a coat dosage. And comparison it analyzes the movable present condition of thread use dosage and the freezer. It presents the improvement direction against enemy conditions heat source equipment selecting. Also, currently it produces the dosage of heat source equipment and application it tries. The result, the various safety rate and the premium rate which it uses universally are considered above thread using. The reappraisal for enemy conditions heat source equipment selecting which it follows hereupon is necessary.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.903-908
• /
• 2006

Building energy simulation has become a useful tool for predicting cooling, heating and air-conditioning loads for facilities. It is important to provide building energy performances feed back to the mechanical and electrical system operator and engineer for energy conservation and maintenance of building. From this research, we set up the typical weather data of location, basic description of building, geometric modelling data and the specification of Installed primary HVAC system for establishing the simulation model about energy consuming that take place in multipurpose building complex. The simulation tool of building energy - EnergyPlus (DOE and BLAST based simulation S/W), it has been used and accomplished calculations and analyses for evaluating the effect of the system types and operating condition of central HVAC plant on the building energy consumption. In this paper, we offer comparison and simultaneous results those involve electricity consumption pattern and amount between actual operation versus EnergyPlus simulation to the object building during summer season.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1175-1182
• /
• 2004

Installations of vertical boreholes for the ground source heat pump system are expensive to install. One way to reduce the initial cost is to increase the specific heat extraction rate of borehole system. However, as the specific heat extraction rate increases the temperature of borehole fluid decreases with the resultant lower Coefficient Of Performance in Heating(COPH) of heat pump system. The purpose of this study is to provide the basic informations about the performance of heat pump system with the specific heat extraction rate and soil thermal properties such as thermal conductivity and temperature. It is shown that the specific heat extraction rate is the most important parameter for the ground source heat pump system. To obtain the reasonable COPH value (COPH > 3) the heat extraction rate should be about 25 W/m or less. Accurate measurements of soil thermal properties are also very important to design the system properly. The effects of borehole thermal resistances are also examined in this study.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.183-192
• /
• 1996

This paper presents a numerical model of the optimal operation pattern of the CHP system built for duel-purpose of power generation and district heat production. The model can be differently formulated in accordance with the view of planner: society, electric utility or district-heating company. Here, the operation pattern of the system components and the effect of heat price are of major interest in the study. From the case study, it was found that the optimal use of auxiliary heating equipment is very important to achieve the minimum societal cost. And, the multi-step heat pricing scheme is desirable to induce the voluntary behavior of both companies towards the societal optimal pattern.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.31 no.1
• /
• pp.9-14
• /
• 2002

산업의 발전에 따른 도시화의 영향으로 대도시에서는 가용공간을 확보하기 위하여 건물의 고층화와 지하공간의 개발이 활발하게 이루어지고 있다. 최근 증가추세에 있는 초고층주상복합건물, 초고층아파트는 건물의 높이가 증가함으로 인하여 건축공사비의 증가는 물론 설비적인 측면에서는 저층부의 수압이 상승 하여 높은 수압과 수격작용(water hammer)에 대한 배관 및 기기의 내압강도와 안전대책이 요구된다. 또한 건물의 초고층화로 인하여 열원에서 공조기까지, 공조기에서 실내기기까지의 수직거리 (vertical distance)가 길어지게 되어 연장된 공조덕트 및 배관 의 길이로 인해 반송동력비의 상승에도 큰 영향을 미치게된다. 이러한 문제점을 해결하기 위하여 기기 및 재료의 선정시 내압을 고려하거나 기기의 적정배치와 조닝(zoning)을 통해 상기의 문제점을 해결하는 방법을 적극 채용하고 있다. 하지만 보다 근본적인 문제해결 방법으로 건물의 층고저감에 의한 건축공사비 및 연 간운전비의 절감을 통한 건물에서의 소비에너지량 감소로 부존자원이 부족한 우리나라의 에너지수급정책에 기여하여야 할 것이다. 본 고에서는 건축물의 층고저감 효과를 얻을 수 있는 공조시스템에 대해 전반적으로 기술하고자 한다.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.18 no.4
• /
• pp.365-388
• /
• 1989

열병합발전시스템은 엔진 또는 가스터빈구동의 열병합발전설비이며, 전력과 열을 동시에 이용함으로써 높은 총합열효율이 기대되는 열원시스템이다. 그 경제성은 전력과 열의 수요가 년간을 통해서 안정하게 존재할 것이 필요조건으로 된다. 본보는 일년간의 운전기록을 사용하여 현재 가동하고 있는 시스템의 특성, 전력수요와 열부하의 실태를 분석하여 개략적으로 설명하는 것이다. 해석에 사용된 자료는 시간단위의 계획치, 적산치이며, 데이터입력후의 인산, 통계, 도표 작성등은 전부 전산기시스템으로써 처리하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.729-732
• /
• 2007

폐 자동차에서 발생하는 폐차잔재물(Automobile shredder Residue)의 시멘트 열원 활용을 위하여 시멘트 킬른에서의 염소제어기술을 확립하고자 하였다. 이를 위하여 본 연구에서는 ASR 발생공정에서 발생량이 가장 많은 light fluff 시료를 채취하였으며, 채취한 시료의 염소함량 분석 및 이를 토대로 하여 시멘트 킬른에서의 염소함량 순환거동을 예측하였다. 아울러 킬른내 염소제어설비의 안정적 가동을 위하여 기존 염소제어 시스템인 태평양 시멘트회사 시스템과 우베 시멘트회사 시스템의 장단점을 비교분석하여, 시멘트 킬른 내부에 함유되어있는 다량의 염소성분을 제어할 수 있는 기술개발 방향을 제시하고자 하였다.