• Journal of the Korea Society for Simulation
• /
• v.23 no.2
• /
• pp.17-24
• /
• 2014

This study attempts to show an example of developing and applying thermal hydraulic simulation model for Aircraft-EHA. The overview of research procedure is as in the following. First, The unit hydraulic simulation model, which reflects physical quantity answering engineer's purpose is developed. Second, The unit hydraulic simulation model is combined, and then branched out to EHA hydraulic model. Third, a simulation model including flow thermal is developed, and then oil temperature rise time according to 'initial temperature and load' is examined. Finally, the master graph that can be used for designing EHA combined with thermal hydraulic analysis results in several cases is compiled, and suggested. AMESim, commercial software, is used through whole procedure.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.29 no.1
• /
• pp.30-38
• /
• 1993

In this study, the combustion characteristics in a pre-combustion chamber diesel engine was investigated with experimental conditions of marine engine load. The heat release analysis used was a single-zone single-chamber thermodynamic analysis based on pre-combustion chamber pressure-time data. Based on the results of this investigation, the following conclusions were reached: 1) Increasing the load, peak pressure was increased and position of P sub(max) was retarded in crank angle degrees. 2) Ignition delay time was almost constant without relating to the load and the heat values to form a combusitible mixture were decreased apparently with increasing the load. 3) In premixed-combustion mode, the pattern of heat release rate was resembled without relating to the load and premixed-combustion time was shortened with increasing the load. 4) Increasing the load, mass of premixed-burned fuel was increased slightly, but was invariable beyond a certain fuel-air ratio. 5) Increasing the load, premixed-burned fraction was decreased.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.468-468
• /
• 2014

우리나라는 미국, EU, 러시아, 중국, 인도 등 다국간 협력 사업인 국제핵융합실험로(ITER) 사업에 참여하고 있으며, 블랑켓 일차벽 및 시험용 블랑켓 모듈(Test Blanket Module, TBM) 제작기술 개발에 필요한 고열부하 검증시험을 국내에서 자체적으로 실시하기 위한 고열부하시험 시설을 구축하였다. 한국원자력연구원에 설치된 고열부하시험 시설의 주요 사양은 다음과 같다. 열원으로는 전자빔을 사용하며, 빔출력은 최대 300 kW이고, 최대 출력밀도는 $10GW/m^2$이다. 전자빔의 최대 가속전압은 60 kV이고, 최대 조사 면적은 설계상 $70cm{\times}50cm$이다. 고열부하 장비는 핵융합환경과 유사한 고열부하를 시험대상물에 인가하여 접합 및 냉각 성능을 평가하는 장비이며, ITER 블랑켓 및 TBM 일차벽의 경우 약 $0.5MW/m^2$, 가속실험 혹은 사고 시 순간 시나리오 해석을 위해서 $5MW/m^2$까지 고려되기도 한다. ITER 블랑켓 일차벽 제작기술 개발 및 검증(2004~2011)에서는 외국장비(러시아 TSEFEY, 일본 JEBIS, 독일 JUDITH)를 활용하였으나, 고비용 문제와 장비 이용 시간의 제한에 따라 사용이 어려워, 국내에서는 KoHLT-1, 2 장비를 자체 구축하여 활용하여 왔다. 현재는 높은 열부하 인가조건, 약 $5MW/m^2$을 달성하기 위해서 전자빔을 이용한 고열부하시험 장치를 마련하였으며, ITER 블랑켓 일차벽 Semi-Prototype 검증시험, TBM, KSTAR 디버터 실험 등 핵융합로 일차벽 개발에 활용하고 있다. 전자빔, 전원 및 진공 chamber 등 전체 고열부하 시험장치를 구축하여 ITER 장치를 포함해서 토카막 디버터 등 핵융합 플라즈마 대면부품 (Plasma Facing Components, PFC) 재료 개발과 국방, 항공우주 분야의 열유속 게이지 측정법 향상 연구, 로켓 추진 엔진 연소실의 열유속 모니터링 연구, 항공기 프로펠러 연구 등에 활용할 수 있을 것으로 기대된다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.261-268
• /
• 2001

An investigation on nondestructive evaluation of thermal stress-nduced damage in the composite laminates (3mm in thickness and $[+45_6/-45_6]_s$ lay-up angles) has been performed using the thermo-acoustic emission technique. Reduction of thermo-AE events due to repetitive thermal load cycles showed a Kaiser effect. An analysis of the thermo-AE behavior determined the stress free temperature of composite laminates. Fiber fracture and matrix cracks were observed using the optical microscopy, scanning electron microscopy and ultrasonic C-sean. Short-Time Fourier Transform of thermo-AE signals offered the time-frequency characteristics which might classily the thermo-AE as three different types to estimate the damage processes of the composites.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.1
• /
• pp.19-26
• /
• 2010

A PEMFC(proton exchange membrane fuel cell) is a good candidate for residential power generation to be coped with the shortage of fossil fuel and green house gas emission. The attractive benefit of the PEMFC is to produce electric power as well as hot water for home usage. The thermal management of PEMFC for RPG is to utilize the heat of PEMFC so that the PEMFC can be operated at its optimal efficiency. In this study, thermal management system of PEMFC stack is modeled to understand the dynamic response during load change. The thermal management system of PEMFC for RPGFC is composed of two cooling circuits, one for controling the fuel cell temperature and the other for heating up the water for home usage. The different operating strategy is applied for each cooling circuit considering the duty of those two circuits. Even though the capacity of PEMFC system (1kW) is enough to supply hot domestic water for residence, heat-up of reservior takes some hours. Therefore, in this study, time schedule of the simulation reflects the heat-up process. Dynamic responses and operating strategies of the PEMFC system are investigated during load changes.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.1094-1095
• /
• 2004

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.1
• /
• pp.76-83
• /
• 2011

This paper focuses on the thermal design of a signal processor in Micro-Wave Seeker. High temperature environment and ESS(Environmental Stress Screening) test condition should be considered in designing a signal processor. First, we performed the thermal analysis to know conditions under which a signal processor is thermally reliable. As a result of thermal analysis, we found that adopting heat transfer block to the thermally fragile components is most efficient, because the heat transfer block can control the thermal loads of the individual components. Next, we verified this solution by numerical simulation and experiment and concluded that thermal reliability of a signal processor can be achieved. Maximum temperature difference between numerical simulation and experiment is about $2^{\circ}C$.

• Composites Research
• /
• v.16 no.1
• /
• pp.26-33
• /
• 2003

Utilizing a thermo-acoustic emission (AE) technique, a study on detection and evaluation of microfractures in cross-ply laminate composites was performed. Fiber breakages and matrix fractures formed by a cryogenic cooling at $-191^{\circ}C$ were observed with ultrasonic C-scan, optical and scanning electron microscopy. Those microfractures were monitored in a non-destructive in-situ state as three different types of thermo-AE signals classified on the basis of Fast-Fourier Transform and Short-Time Fourier Transform. Thus, it was concluded that real-time estimation of microfracture processes being formed during cryogenic cooling could be accomplished by monitoring such different types of thermo-AEs in each time-stage and then by analyzing thermo-AE behaviors for the respective AE types on the basis of the AE signal analysis results obtained during thermal heating and cooling load cycles.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.33-36
• /
• 2009

콘덴서는 유도성 부하의 늦은 역률 보상으로도 사용되며, 비선형 부하에서 발생하는 고조파를 저감하기 위해 리액터에 직렬로 연결하여 사용되기도 한다. 콘덴서는 전압이 증가할 경우 전류도 함께 증가하고, 주파수가 증가할 경우 콘덴서에 흐르는 전류가 증가하기 때문에 전류의 증가는 바로 열의 증가로 콘덴서 절연에 스트레스로 작용하여 고장의 원인을 제공할 수 있다. 본 연구에서는 콘덴서에 인가되는 전압의 크기와 주파수를 변화시킬 경우 콘덴서에서 발생하는 열을 열화상 카메라로 측정하여 외부 및 내부에서의 온도분포를 분석하였다. 측정결과 전압과 주파수가 증가할 경우 콘덴서에서 열이 매우 높게 분포함을 확인할 수 있었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.147-158
• /
• 1997

This paper presents the analysis technique and procedure of main engine components-cylinder block, cylinder liners, gasket and cylinder head-using the finite element method, which aims to assess mainly the potential of lower oil consumption in a view point of engine design and to decide subsequently the accuracy of engine design which was done. The F.E. model of an engine section consisting of one whole cylinder and two adjacent half cylinders is used, whereby the crankcase is cut off at the block bottom deck. By means of a 3-dimensional F.E. model-including cylinder block, liners, gasket, cylinder head, bolts and valve seat rings as separate parts a linear analysis of deformations and stresses was performed for three different loading conditions;assembly, thermal and gas loads. For the analysis of thermal boundary conditions also the temperature field had to be evaluated in a subsequent step.