• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.2
• /
• pp.147-155
• /
• 2008

Three groups of dentin bonding agents (5th generation Single Bond 2.0 and two 6the generation Prompt L-Pop, AdheSE) applied to class V cavities (upper portion with enamel margin and lower portion with dentin margin) prepared at buccal and lingual portion of premolars and molars. Each groups consist of 30 teeth. Devide into two groups, one without thermocycling and the other thermocycled. After then, infiltrate methylene blue into the gap between restoration and tooth. Within non-thermocycled groups, Single Bond 2.0 group shows lesser leakage at enamel margin than other two bonding agents (p <.05) but shows more leakage at dentin margin than other two bonding agents. (p <.05) Within thermocycled groups, Single Bond 2.0 group shows lesser leakage at both enamel and dentin margins. (p <.05)

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.225-226
• /
• 2009

본 연구에서는 신경망과 웨이브릿을 결합하여 플라즈마 챔버의 누출을 감시하기 위한 시계열 모델을 개발하였다. 플라즈마 데이터는 광반사분광기 (Optical Emission Spectroscopy-OES)를 이용하여 측정하였으며, 이를 시계열 신경망을 이용하여 모델링하였다. 이산치 웨이브릿 (Discrete Wavelet Transformation)은 OES 센서정보의 전 처리를 위해 이용되었다. 개발된 웨이브릿 신경망 모델은 47개의 데이터 sets을 이용하여 평가하였으며, 누출상태를 효과적으로 탐지할 수 있었다.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.44 no.1
• /
• pp.89-98
• /
• 2017

The aim of this study was to compared the penetration scores and microleakage levels of flowable resin in comparison to resin-based pit and fissure sealant. A total 120 extracted premolars were used and classified with group I (resin-based pit and fissure sealant), group II (flowable resin), group III (bonding agent + flowable resin), IV (fissurotomy + bonding agent + flowable resin) depending on the materials and the application methods. The penetration scores of the group treated with flowable resin following fissurotomy were similar to those of the group treated with resin-based sealant, but higher compared to those of the other groups treated with flowable resin without fissurotomy or bonding agent. The group treated with flowable resin following fissurotomy also exhibited the lowest microleakage levels. The group treated with resin-based sealant and the one treated with a bonding agent prior to the application of flowable resin showed similar microleakage levels. In conclusion, flowable resin may be applied as a pit and fissure sealant, and its application along with fissurotomy could increase the penetration scores.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.4
• /
• pp.317-326
• /
• 2020

In this study, damages caused by flash fire, overpressure, and thermal radiation based on the sizes of leak holes were evaluated using the areal location of hazardous atmospheres when natural gas leaked owing to the damage of pipeline in a LNG fueled ship. In addition, environmental variables (wind speed, atmospheric temperature, and atmospheric stability) and process variables (pipe pressure and pipe length) were classified to analyze the damage impact ranges caused by various scenarios. From the results, the damage range caused by the environmental variables was the largest, followed by overpressure and thermal radiation. Additionally, for the process variables, regardless of the pressure, length, or size of the leak holes, the damage range attributed to flash fire was the most significant, and the damage range was high in the order of overpressure and thermal radiation, similar to the environmental variables. The larger the size of the leak holes, the higher the values of the environmental and process variables, and the higher the damage range caused by jet fire compared to the environmental variables.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.45 no.1
• /
• pp.90-97
• /
• 2018

The purpose of this study was to evaluate the effect of fissurotomy on the penetration and microleakage of flowable resins for carious fissures. A total of 250 extracted premolars with early fissure caries were selected and divided into five groups according to the fissurotomy; no fissurotomy (n = 50), fissurotomy with $Fissurotomy^{(R)}$ original bur (n = 50), fissurotomy with $Fissurotomy^{(R)}$ Miro NTF bur (n = 50), fissurotomy with SF104R tapered diamond bur (n = 50), fissurotomy with 1/2 round carbide bur (n = 50). Two types of flowable resins ($UniFil^{(R)}Flow$, $Filtek^{(R)}Flow$) were used as sealing materials. All samples were sectioned and observed using a stereoscopic microscope after thermocycling and immersing in methylene blue solution. The adaptation of flowable resin to the fissure wall was observed using scanning electron microscopy. The penetration of flowable resin into the carious fissure was significantly increased by fissurotomy, which also decreased microleakage. Fissure preparation using different burs showed a significantly different in penetration, but did not show any difference in microleakage. $Unifil^{(R)}Flow$ showed better penetration than $Filtek^{(R)}Flow$, but there was no significant difference in microleakage. Fissurotomy can be used to increase the penetration of flowable resin into carious fissures and decrease microleakage.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.1083-1086
• /
• 1999

중수로(CANDU) 형 월성 원자력발전소의 칼란드리아 압력관 전면부를 감시점검하기 위한 열영상 관측시스템을 설계/제작하였다. 중수로는 가동중에 핵연료를 교체한다. 칼란드리아 전면부에는 380 개의 압력관 채널이 위치하고 있다. 핵연료를 교체할 시에 핵연료 교체장비가 칼란드리아 압력관 채널의 ENDCAP을 열고 핵연료를 장전하는 과정에서 발생할 지도 모르는 중수누출, 핵연료교체장비의 이상상태를 점검하는데 목적이 있다. 열영상카메라는 상용 CCD 카메라에 비해 영상의 해상도가 떨어진다. CCD 카메라는 수증기 누출과 같은 육안검사에 활용하고, 열영상카메라는 압력관 채널의 온도변화 등을 점검하기 위해 CCD/열영상카메라의 융합구조로 설계/제작하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.825-833
• /
• 2018

In this study, one calculated the range of damage to the combustion characteristics according to the composition of LNG and the size of leaking holes, and analyzed the damage effect in case of leakage accidents caused by pipe damage in the re-gasification process for the LNG supply system. In order to confirm the combustion characteristics according to LNG composition, there was no significant difference in the result of risk analysis by LNG-producing areas. However, the higher the methane content of the components, the lower the risk of flash fire, hazardous areas of overpressure due to explosion, and thermal radiation damage caused by jet fire. In addition, one investigated the effect of leakage, holes, and ruptures on the risk range and explosions according to the size of the pipe-leakage hole. Also, the influence of overpressure and the range of damage from radiant heat could be predicted. One confirmed the effect of LNG composition and pipe-leakage size on fire and explosion.

• Environmental and Resource Economics Review
• /
• v.21 no.3
• /
• pp.519-542
• /
• 2012

In this paper, we empirically analyzed whether carbon leakage really happened in EU by comparing before and after the period of EU ETS. We regarded foreign direct investment outflows as indicator of carbon leakage and analyzed panel regression between production cost including environment cost and this FDI variable. Also we consider foreign market potential to analyze market oriented FDI. According to this analysis, carbon leakage was observed in some models for manufacturing industry. However carbon leakage did not prove consistently in a variety of models and it is hard to speak carbon leakage was happened in EU ETS. Notwithstanding relatively short time series of data, in the view of the fact that carbon leakage was tested in some models, Korea also should keep in mind the possibility of carbon leakage and design emission trading scheme.

• Journal of dental hygiene science
• /
• v.11 no.4
• /
• pp.333-337
• /
• 2011

The purpose of this experiment was to examine possibility of microleakage by water, temperature change, and bite force inside the mouth during the period of using light-activated temporary filling materials. 2 kinds of light-activated temporary filling materials were used in order to measure weight and compressive strength and to evaluate microleakage between filling material and cavity wall according to frequency of thermal circulation. First, Light-activated temporary filling material was increased the weight, which was measured according to the period of using. As for the result of comparing between products, the weight of Quicks was indicated to be higher. Second, Compressive strength of Spacer had significant difference depending on period of using. However, significant difference wasn't shown in the compressive strength of Quicks. In Spacer that showed significant difference, the compressive strength increased greatly in the difference of 3 days. Third. As for micro-leakage according to frequency of thermal circulation, the microleakage was indicated to be the highest in the group that carried out 7,000 times. The group with operation of 1,000 times and the group with operation of 3,000 times were indicated the statistically lower micro-leakage than the group with operation of 7,000 times. This study brought about a rise in micro-leakage depending on the passage in the period of using. However, it is obvious fact that micro-leakage increases according to the passage of time after restoration.

• The korean journal of orthodontics
• /
• v.39 no.6
• /
• pp.393-401
• /
• 2009

Objective: The purpose of this study was to compare the shear bond strength (SBS) of brackets and microleakage of a tooth-adhesive-bracket complex bonded with a direct and an indirect bonding technique after thermocycling. Methods: Fifty non-carious human premolars were divided into two equal groups. In the direct bonding group a light-cured adhesive and a primer (Transbond XT) was used. In the indirect-bonding group, a light-cured adhesive (Transbond XT) and chemical-cured primer (Sondhi Rapid Set) were used. After polymerization, the teeth were kept in distilled water for 24 hours and thereafter subjected to thermal cycling (500 cycles). For the microleakage evaluation, 10 teeth from each group were further sealed with nail varnish, stained with 0.5% basic fuchsin for 24 hours, and examined under a stereomicroscope. Fifteen teeth from each group were used for SBS testing with the universal testing machine and adhesive remnant index (ARI) evaluation. Data were analyzed using the Mann-Whitney U test, Chi-square test, and Fisher's exact test. Results: There were no statistical differences on SBS and microleakage between the two bonding techniques. The indirect bonding group had a significantly lower ARI score. Bracket failures were obtained between enamel-resin interfaces. Conclusions: The type of bonding technique did not significantly affect the amount of microleakage and SBS.