• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.205-212
• /
• 2013

This paper presents the results of a numerical study on the effects of a side guide on the top and tail camber. The temperature distribution on the surface of an actual hot-rolled bar was measured using a thermal imager. The measured temperatures were incorporated with finite element analysis, and the thermomechanical behavior of the hot bar was examined. The installation location of the side guide, length of the side guide, and gap between the bar and the insides of the side guide were selected as the parameters to be investigated. The results show that it is more effective to install the side guide at the position where the magnitude of the camber is larger. It is noted that a longer side guide is more effective than a shorter one in reducing the camber. It is also found that the camber decreases in proportion with the guiding gap.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.68-76
• /
• 1991

최근 열간압연의 공정이 단순하고 회수율이높은 CC재 (연속 주조재)가 IC재 (Ingot 주조재)에 비해 냉간압연 재료의 주종을 이루고있으며, Roll 조도의 급속한 저하로 슬립현상과 채터링현상 등이 발생한다. 본 연구에서는 Work Roll 마멸 및 조도 저하에 큰 영향을 미치는 (1) 압연 가공길이 및 (2) 실험 재료의 종류에 따른 영향과 (3) 압연하중에 의한 Roll 조도변화를 실제 압연가공을 통하여 분석하고, (4) 알미늄 산화 게재물의 영향과 전사율을 연구하고저 한다.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.544-548
• /
• 2007

In general, final width of hot strip should be accomplished in this stage because width reduction of strip hardly appears during typical finishing mill. However, it is difficult to control the width of strip in the roughing mill process as the horizontal rolling of strip is subsequently performed after the vertical rolling. It is therefore important to obtain the deformation rolling direction on strip width to minimize the width spread of strip during horizontal rolling after vertical rolling. Generally there is Sizing press type and Edger-roll type. The width reduction process in sizing press has small amount of width spread compared with the edger. However, productivity by the sizing press process is much lower than those of the edger. In this study, sizing press and Edger-roll process parameters in a sheet rolling mill were set at specified values and the effect of the change in these parameters on product quality and process performance were evaluated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1155-1165
• /
• 1990

A new method of predicting effect of rolling parameters on roll pressure, roll force, and power and energy consumptions in hot strip rolling is presented. The method is based on approximate solutions for velocity, strain rate, and stress distributions in the roll gap. The degree of approximation was examined by the finite element solutions. The theoretical predictions were compared with experimental data from hot rolling of steel strip and steel plate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.819-827
• /
• 1992

Investigations of the fatigue damage of roughing mill roll and experimentally. By the computer simulation for analysing the stresses on the roll surface and experimental hot rolling, the following results were drawn : The crakcs observed on the roll surface were initiated thermally in the initial stage of the rolling and propagated by repeated thermal and bending stresses. The size of the roll surface cracks smaller than 4.87mm could avoid the occurrence of tiny scab, surface defect of hot steel strip. Since the size of surface cracks observed on the roughing mill roll was very small, the fatigue damage of roll surface was found not to be the major factor for the formation of the scab.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.614-618
• /
• 2002

In hot strip mills, Portable Roll Scanner (the portable roll surface temperature and profile measuring device) can be used to calibrate on-line Process models for strip crown and flatness by measuring the thermal expansion and wear profile of the rolls. And the surface temperature measurement can be used to optimize the roll cooling system. Portable Roll Scanner consists of the measuring device, which has two contact inductive distance transducers for roll profile measurement and one infrared Pyrometer for surface temperature measurement, and computer-based controller that is equipped with the measuring device. By the wireless data communication, the data is transferred to the memory of notebook for further analysis. After roll extraction from mills, Portable Roll Scanner measure the roll profile and surface temperature simultaneously along the work roll face and display the results in the TFT color monitor of notebook. Portable Roll Scanner is useful at mill-side and roll grinding shop.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.4
• /
• pp.307-315
• /
• 1989

In this paper, we have analyzed the temperature variation trend of a slab on between the process of reheating furnace and the termination of roughing mill process during hot rolling process. 1) cooling by radiation and convection current in the air, 2) plastic deformation heat, 3) cooling by descaling water, 4) cooling by contact with rolling rolls and/or transmitting rolls. For the analysis, the factors have been adopted as the problems of the rolling process to be solved such that we have established an application technique in relation to the determination of boundary conditions on the slab surface. We have presented a procedure for an analysis of the cooling phenomenon treated as a problem of two-dimensional transient heat flow using finite difference equation and suggested techniques of implementing sequentialized rolling tasks in correlation with the procedure. From the result of simulation, it is shown that the difference between calculation value and measurement value is within the range of the industrial measurement error. Also, it is proved that the assumptions, conditions, and properties used in the computer simulation is appropriate by showing that the pattern of a drop in temperature at each rolling event is in accord with real circumstances.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.13-16
• /
• 2000

In the hot strip mill, a bad threading and shape of strip strip in the finishing mill was caused by asymmetric rolling In roughing min. Mathematical analysis for camber control of roughing mill in hot strip rolling has been developed. Each equation in the camber control model was derived from geometrical characteristics of camber mechanism. The model can predict variables such as wedge, side slippage and roll force difference etc. from a measured camber value and then find an optimum roll gap condition for minimizing camber in the next pass.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.1
• /
• pp.129-136
• /
• 2012

This study seeks to evaluate the welding characteristics of SHN400 steel, which is suitable for the steel material used in building structures in KS. For this purpose, the Y-groove weld crack test and hardness, tensile, bending, cross tensile, and charpy V notch tests at the welding point were conducted with specimens taken from the highest, the thickest and the commonly used H-beams for girder or beam members. Each test was conducted under the KS test conditions. All tests results satisfied the requirements of KS and the welding requirements for the proper inelastic behavior of structure, indicating that SHN400 can be used for the building structure as a structural material.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.4
• /
• pp.515-522
• /
• 2011

The purpose of this study was to evaluate the material characteristics of SHN400 steel, which is suitable as a steel material for building structures, using the experimental approach. For this purpose, the chemical composition test, tensile test, macro test, micro test, and charpy notch impact test were conducted with specimens taken from the highest, thickest, and commonly used H-beams for girder or beam members. Each test was conducted under the Korean Standard(KS) test conditions. All the test results satisfied the requirements of KS (KS D 3866) and the steel material for seismic design. The carbon equivalent value (Ceq), which is related to weldability, and the yield ratio, which is related to inelastic behavior, showed especially good results. Thus, SHN400 is definitely suitable as the steel material for building structures.