• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.274-278
• /
• 1992

냉간압연기술의 발달로 냉간압연기도 매우 다양하게 발달되었으며 냉간압연의 원자재인 열간압연재의 종류도 다양하다. 최근 열간압연가공시 회수율이 높은 연속주조재(Continuous casting strip)인 CC 재가 종전의 가공과정이 복잡하며 불량율이 높은 Ingot주조재(Ingot casting strip)인 IC 재 보다 생산비율이 점차 증대되어 냉간압연재료의 주종을 차지하고있다. CC재는 냉간압연가공시 IC재에 비해 Work roll 조도저하가 현저하게 크기 때문에 슬립(Slip)과 채팅(Charttering) 현상 등이 발생하여 압연가공성이 불안정 하게 되어 Work roll과 판표면에 손상이 생기게 되고, 압연가공시 Roll 사고 등의 문제가 발생하므로 Roll 마멸의 정도를 파악하여 Roll을 효과적으로 관리하므로써 Work roll과 판표면의 슬립현상 및 채터 링현상 등을 방지할 수 있다.

• Korean Journal of Optics and Photonics
• /
• v.27 no.4
• /
• pp.127-132
• /
• 2016

In this paper, a trench structure was fabricated by femtosecond-laser machining to eliminate thermal crosstalk in a multichannel variable optical attenuator (VOA), to prevent decreasing attenuation efficiency of the VOA. Trenches of a variety of widths and depths were fabricated on the VOA chips by femtosecond-laser processing. After the machining, attenuation according to current change was observed in each VOA chip module with trenches. As a result, we could observe high responsivity of attenuation and low power consumption, and that the heat of each channel barely influenced other channels.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.26-29
• /
• 2008

Recently, the hydroforming of high strength aluminum tubes has many studies and applications in manufacturing industry, especially in automotive industry. But high strength aluminum tube has limited expansion capability at most 15% at normal temperature. New manufacturing process, called hot air forming, is introduced to apply aluminum tube to the automotive sub frame components which have complex shape and require high expansion ratio about 40%. The process is carried out at the elevated temperature above $500^{\circ}C$, so numerous material properties and process parameters related to high temperature should be investigated and determined to get a sound product. In this paper, the hot air forming process of automotive sub frame was investigated. The effect of the forming parameters such as the temperature of tool, axial feeding and gas pressure are analyzes by using explicit finite element method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.4
• /
• pp.47-54
• /
• 2013

The main cause of die failure in hot forging is wear. Die wear directly generates the gradual loss of part tolerances, thereby causing deterioration in the dimensional accuracy of a forged part. It is very important to estimate forging cycles, called as die life, at which the die should be repaired or replaced. In this study, in order to estimate the hot forging die life, the finite element simulation of wear on an asymmetric part like a ball joint socket used in vehicle was carried out based on Archard's model. Finite element simulation results were compared with wear amounts of a used die that were measured using a contact stylus profilometer. The simulation results were in relatively good agreement with measurements obtained from the virtual die which was used by 7,000 forging cycles in a forging industry. Consequently, the die life in the hot forging of the ball joint socket was estimated by 10,500 forging cycles on the finisher die.

• Journal of Korea Foundry Society
• /
• v.27 no.5
• /
• pp.212-216
• /
• 2007

과공정 Al-15wt.%Si 합금의 주단조 공정의 적용을 위해 주조 예비성형체를 제작하는 과정에서 P와 Sr을 첨가하여 과공정 Al-Si 합금의 응고과정에서 발생하는 초정 Si과 공정 Si의 미세화 개량처리를 행하였다. 미세화 조직의 변화에 따른 기계적성질 및 단조성을 조사하였으며, 미세화제로 첨가된 0.075wt.% Sr과 0.1wt.% P의 첨가에서 가장 효과적인 미세한 조직을 얻을 수 있었고, 인장강도와 연신율은 이들 첨가원가의 증가에 따라 향상되는 결과를 보였으나 일정 이상의 첨가에서는 더 이상의 향상은 없었다. 단조성 평가를 위한 열간가공 재현실험에서는 $450^{\circ}C$에서 약60N/mm2의 하중이 필요함을 알 수 있었다. 열간단조 및 열처리 후의 인장강도와 연신율은 보다 많은 향상을 가져왔으며, 이는 압축가공에 의한 주조 예비성형체 내부에 잔존하던 주조결함의 제어와 열처리에 의한 조직의 개량 및 균질화 효과에 의한 것으로 판단된다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.06a
• /
• pp.92-92
• /
• 2006

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.189-189
• /
• 2007

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.368-368
• /
• 2007

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.06a
• /
• pp.31-42
• /
• 2005

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.257-257
• /
• 2008