• Polymer(Korea)
• /
• v.35 no.4
• /
• pp.337-341
• /
• 2011

To expand the viewing angle of vertical alignment liquid crystal display (VA-LCD), a wide-band compensation film has been newly developed. VA-LCD needs a retardation film with improved oblique viewing property. The retardation film for VA-LCD has been fabricated by solvent casting and subsequent drawing triacetylcellulose (TAC) containing optical additives. Here, optical birefringence and wavelength dispersion of the retardation film strongly depend on the chemical structures of optical additives. Utilizing quantum mechanical computation, the polarizing anisotropy of retardation film was calculated with respect to additives. It is also realized that the wavelength dispersion of polarizing anisotropy depends on the type and location of substituent to the selected main isomer. When two propionates are substituted to the meta position of the selected main isomer, the wavelength dispersion of polarizing anisotropy shows the most gentle slop, which is well matched with the experimental results. The most gentle slop of wavelength dispersion means that the viewing angle characteristics of LCD are less influenced according to the wavelength of light source of LCD, and it's possible to make better image quality than the present level.

• Membrane Journal
• /
• v.22 no.1
• /
• pp.72-76
• /
• 2012

$SF_6$ has an extremely high global worming potential (GWP). Therefore, there has been an effort to reduce the use of $SF_6$ and its emission into atmosphere. One possible solution for minimizing the use of $SF_6$ in electrical equipments is utilization of gas mixtures such as $SF_6/N_2$. The $SF_6$ concentration in the gas mixture varies from 10 to 60%. However, when the apparatus is repaired or dismantled, we have to recover $SF_6$ from the gas mixture. Since the boiling point of $SF_6$is low (${\sim}-60^{\circ}C$), the liquefaction method is difficult to apply. One possible alternative is the membrane separation technology. In this study, we investigated the $SF_6$ and $N_2$ permeation properties of 5 polymeric membranes. For example, permeability of $N_2$ in BOPP membrane at $25^{\circ}C$was 0.19 barrer, whereas that of $SF_6$ was only 0.0012 barrer, resulting in the selectivity of 158. An upper bound for $SF_6/N_2$ gas pair was suggested for the first time with n = -1.33 and k = 160 (barrer).

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.253-260
• /
• 1993

High strength and fracture toughness of Al-Li-Cu alloy(2090 Al alloy) have been achieved by the improvement of melting and casting, extrusion and heat treatment techniques. To establish the sucessful process for semi-industrial scale ingot(20Kg) the following areas have been investigated: (1) Improvement of melting and casting techniques for ingot by introducing atmospheric modifications, vacuum and rotary degassing, and deslagging. (2) The effect of heat treatment on mechanical properties (3) Mechanical characterization by tensile test, fracture toughness test and fatigue crack propagation test. High mechanical properties were found to be intimately related with ingot soundness. Tensile strength of final products varied from 534MPa to 566MPa in peak aged condition while elongation/ductility ranged from 9.0% to 11.9%. From the fracture toughness test with using compact tensile specimen, plane strain fracture toughness($K_{Ic}$) appeared to be 39MPa${\surd}$m in peak aged condition and 23MPa${\surd}$ m in underaged condition. When load ratios of 0.1, 0.3 and 0.5 were given ${\Delta}K_{th}$ was 6.0MPa${\surd}$ m, 5.3MPa${\surd}$ m and 4.3MPa${\surd}$ m respectively.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1252-1262
• /
• 1999

The effect of microstructures on the strength-flangeability of Nb bearing hot-rolled high strength steel was investigated in order to improve the strength-flangeability of conventional TS 580MPa grades HSLA steel for the automotive wheel disc. The low temperature coiling method using 3-step controlled cooling pattern after hot rolling was effective to produce the Nb-bearing high strength steel with the polygonal ferrite and bainite duplex microstructures. It was suggested that the suppressed precipitation of grain boundary cementites and the decreased hardness difference between ferrite matrix and bainite cause the excellent stretch-flangeability of ferrite-bainite duplex microstructure steel. Therefore, the formation and propagation of microcracks were suppressed relative to the conventional HSLA steel with ferrite and pearlite microstructure. In addition, the elongation was improved as compared with that of hot-rolled steel sheets using conventional early cooling pattern because the volume fraction of polygonal ferrite was increased.

• Current Research on Agriculture and Life Sciences
• /
• v.20
• /
• pp.99-105
• /
• 2002

To develop good soybean varieties for sprouts. 285 indigenous lines and 16 recommending varieties were evaluated by the sprout and agronomic characteristics. The range of whole length, hypocotyl length, root length, and yield rate of sprouts was 9.5~23.0cm, 5.9~15.1cm, 3.2~9.2cm, and 121~695%, respectively. Yield rate of sprouts was the highest, 409%, in the lines of mixed seed coat color. At the same time, it was reversely proportional to seed weight : the smaller the seed weight, the higher the yield rate as in all other reports. The number of roots was significantly fewer in the lines of the black and the green seed coat color than others. Based on whole length, rate of root length, and yield rate of sprouts, many indigenous lines were evaluated much better than recommending varieties. In the hypocotyl color of sprouts, the brightness was higher in improved variety than indigenous lines but vice versa in redness and yellowness in general.

• Current Research on Agriculture and Life Sciences
• /
• v.26
• /
• pp.71-79
• /
• 2008

It is known that the content of asparagine, an excellent detoxifying substance of alcohols in human body, is the highest in the roots of soy-sprout. At the same time, it is inferred that soy-sprouts producing more roots are better for detoxifying. In this experiment, the effects of room temperatures on number of watering per day, and duration of soy-sprout culture were carefully investigated. Some of the results obtained are as follows; 1. The yield rate of soy-sprouts for Agakong and Pungsannamulkong was continuously increased up to 9 days. It was higher in room temperature of $30^{\circ}C$ than in $20^{\circ}C$ and was the highest at 8th day of culture with 5 times of watering per day. 2. The asparagine content in soy-sprouts of Agakong and Pungsannamulkong was the highest in cotyledon and the lowest in roots. This rate was higher in the room temperature of $20^{\circ}C$ than in $30^{\circ}C$. 3. The highest asparagine content of soy-sprout of Agakong was 18.9%, obtained in the room temperature of $30^{\circ}C$, cultivated for 8 days with 5 times of watering per day. 4. The highest asparagine content of Pungsannamulkong was 18.8%, obtained in hypocotyl cultivated in the room temperature of $30^{\circ}C$ for 8 days with the number of 2 times watering per day. 5. When an cultivation apparatus of 5 liters volume was used, the optimum seed amount for the highest yield rate was 300g for Agakong and 500g for Pungsannamulkong. At the same time, the number of lateral roots showed increasing tendency with more amounts of soybean seeds used.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.280-288
• /
• 2016

This study proposes improved welding tools for magnesium alloys. Two types of tools were used for friction stir welding (FSW). The effect of the welding tools on the FSW joints was investigated with a fixed welding speed of 200mm/min and various rotation speeds of 400 to 800 rpm. After FSW, the joints were cross-sectioned perpendicular to the welding direction to investigate the defects. A tensile test and Vickers hardness test were conducted to identity the mechanical properties of the joints. Defects were observed when the rotation speed was 400 rpm, regardless of the welding tool, and the amount of defects tended to decrease with increases in rotational speed. Defect-free welds were obtained when the rotation speed was 800 rpm. The best weld quality was acquired using the C type welding tool. The rotation speed of 800 rpm and welding speed of 200 mm/min produced the best joining properties. The ultimate tensile strength, yield strength, and elongation of the welded region were 90.0%, 69.1%, and 83.2% those of the base metal, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.521-526
• /
• 2017

In the GTA welding process of Al 7075 alloy using different types of filler metals, the tensile test and micro-hardness test were conducted to evaluate the mechanical characteristics. Also, the radiographic test result showed that the weld met the criterion of level 1 in accordance with KS D 0242 for verifying the welding integrity and there were no welding defects. The tensile test result obtained using Al 7075 as a filler metal showed that the material was fractured in the weld zone. The tensile strengths of the materials using Al 7075 and ER 4043 as the filler metal were about 240MPa and 253MPa, their yield strengths were about 132MPa and 120MPa and their elongation percentages were 6.6% and 13%, respectively. The micro-hardness value of the deposited metal zone when using Al 7075 as the filler metal was Hv 132. However, the micro-hardness of the material using ER4043 as the filler metal was about 24% lower than that using Al 7075. When the chemical composition of the filler metal is the same as that of the material itself, fracture can occur in the deposited metal zone. Therefore, it is not desirable to use the same material as the filler metal for the welding of Al 7075 alloy. Moreover, the use of Al-Si based ER 4043 as a filler metal is more desirable than using the same material as a filler metal for welding Al 7075.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.391-397
• /
• 2017

Recently, digital image correlation (DIC) techniques have been used to measure dynamic deformation during tensile testing. The standard tensile test method measures the average displacement of the relevant specimen to calculate the true stress-strain curve. Therefore, the validity of the true stress curve is restricted to the stress incurred within the uniform stretching interval, i.e., the maximum stress corresponds to the starting point of the necking deformation. Alternatively, if DIC is used, the effective range of the strain and strain rate can be extended to the breaking point of the tensile specimen, because of the feasibility of measuring the local strain over the entire area of interest. Because of these advantages, many optical 3D measurement systems have been introduced and used in research and industry. However, the conventional 3D measurement systems are exceedingly expensive and time consuming. In addition, these systems have the disadvantage of a very large equipment size which makes their transport difficult. In this study, a 2D image correction method employing a 2D DIC measurement method in conjunction with a numerical analysis method is developed using a smartphone. The results of the proposed modified 2D DIC method yielded higher accuracy than that obtained via the 3D measurement equipment. In conclusion, it was demonstrated that the proposed 2D DIC and calibration methods yield accurate measurement results with low time costs.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.417-426
• /
• 2016

In this study, the optimal welding condition of an extruded AZ61 magnesium alloy plate was investigated through evaluation of the mechanical properties and microstructure in the friction stir welding zones. The friction stir welding conditions considered in this study were the tool rotation speeds of 400, 600, and 800rpm and the welding speeds of 200, 300, and 400mm/min. To evaluate the welding strength, tensile and hardness tests were carried out. Microstructures of the welded regions were examined using optical microscopes. Under a tool rotation speed of 800rpm and welding speed of 200mm/min, the joint showed the best joining properties. The UTS, yield strength, and elongation of the welded region showed values of 79.0%, 65.4%, and 30.1%, respectively, of those of the base metal.