• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.88-94
• /
• 2012

In this study, the current-voltage curves for metals were measured using cyclic voltammetry. The relationship between the electrochemical properties and surface states of metals were investigated by Scanning Electron Microscope (SEM). In cyclic voltammetry, we used a 3-electrode system for the electrochemical measurements. The measurement was conducted at the condition that consists of the first reduction from the initial potential to -1350 mV, continuous oxidation to 1650 mV, and last reduction to the initial potential. The scan rates were 50, 100, 150 and 250 mV/s. The results show the C-V characteristics of metals to be for an irreversible process, which was caused by the oxidation current from cyclic voltammogram, when monoethanolamine (MEA) was used as a corrosion inhibitor. When we used MEA as a corrosion inhibitor, the diffusion coefficient was decreased as the concentration of electrolyte was increased. In the SEM images of copper, we observed an increase of surface corrosion at the increased electrolyte concentration. Addition of $1.0{\times}10^{-3}M$ corrosion inhibitor MEA reduced the effect of corrosion prevention due to the relatively large diffusion coefficient at the electrolyte concentration of 0.1N.

• Clean Technology
• /
• v.4 no.1
• /
• pp.6-23
• /
• 1998

Recently, semiconductor industry has grown rapidly because of the large demand for electronic devices and equipment. The semiconductor industries have also played an important role on the economic growth in Korea. As the environmental regulations become strict, the proper environmental management and the well-developed waste minimization technologies in semiconductor industries are two of urgent problems to be solved. The semiconductor manufacturing process consists of a series of continuous chemical processes, such as cleaning, oxidation, diffusion, photolithography, etching and film deposition. During the processes, various environmentally hazardous wastes are produced. The wastes may be classified as wastewater, gaseous pollutants, and solid wastes. For waste minimization, the substitution of raw materials and process optimization techniques are used, while the selective destruction technologies of toxic chemicals contained in the wastes have been reported. Also, new technologies have been developed for source reduction and waste reduction, such as reduction of toxic chemical use and substitution of hazardous liquids with gaseous reactants or solvent.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.898-904
• /
• 1998

Ni-W alloys containing 10 to 50wt% W were prepared by electrodeposition. Tungsten content in the alloy increased with current density. X-ray diffraction analysis revealed that the alloy was crystalline phase when deposited at current densities lower than 50mA/${cm}^2$. Their crystal structure transformed to amorphous at higher current densities. In terms of tungsten content, the crystal -+ amorphous transition occurred at 40-46wt% which was identified by the 3 fold increase in the width of a diffraction peak. The lattice parameter of crystalline phase increased with W upto 40wt% which is higher than the solubility limit of W (about 30wt%) in Ni. Therefore, the alloys are considered to be Ni solid solution supersaturated with W. The amorphous Ni-W alloys were recrystallized by annealing them at temperatures over $400^{\circ}C$. This was evidenced by the appearance a strong [ 11 11 annealing texture. The supersaturated W was precipitated during the annealing at over $800^{\circ}C$. The current-density dependence of W content and crystallinity was utilized to produce alternating layers of crystalline (30wt% W) and amorphous (50wt%) phases which may exhibit unique mechanical and corrosion properties.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.1
• /
• pp.15-21
• /
• 2015

Recently, attempts of replacing some of natural aggregate with mix of low quality aggregate are carried out for stable supply of aggregate. However, low quality aggregate such as recycled aggregate produced during the disposal process of construction wastes and by-product aggregate produced by industrial activities has problem of failing to comply to KS Standards. Therefore, we have compared fundamental properties of concrete by using granite crushed aggregate, recycled aggregate, blast furnace and electric arc furnace slag aggregate for effective utilization of lacking aggregate resources. As the result, slump in case of mixed use of aggregate was increased 0~10% compared to single use. Therefore, it is judged to be economically advantageous as it can expect effects in unit quantity or reduction of SP agent. Compressive strength in case of mixed use of aggregate was increased 0~10% compared to single use as it filled internal crevice of concrete with continuous particle size distribution. Accordingly, if we utilize by satisfying standard particle scope through mix of aggregate with different cause of formation in proper ratio, it was possible to confirm utility of mixed aggregate with demonstration of effects of increases of fluidity and compressive strength of concrete.

• Korean Journal of Food Science and Technology
• /
• v.35 no.5
• /
• pp.797-802
• /
• 2003

Structured lipids (SL) were synthesized by esterification of corn oil and conjugated linoleic acid (CLA) in a continuous packed-bed column reactor. The effects of flow rate, reaction temperature, and substrate molar ratios were studied. The reaction was catalyzed by TL IM (immobilized lipase from Thermomyces lanuginosa). Results of triacylglycerol (TAG) analysis by GC showed that the incorporated CLA isomers were mainly cis9, trans11- and trans 10, cis12-CLA. Slower flow rates yielded higher incorporation, and maximum incorporation of CLA was obtained with a molar ratio of 1:3 (corn oil: CLA) at a temperature of $55^{\circ}C$. The obtained SLs had iodine values ranging from 120 to 128. The SLs were composed of TAG $(98{\sim}99%)$, 1,2- and 1,3-diacylglycerol ($0.7{\sim}1.3%$), and a small amount of monoacylglycerol.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5344-5351
• /
• 2013

Chambers in a continuous furnace were designed. A chamber consists of inlets and outlets of nitrogen gas which is used to discharge burned gas and heating pipes (HP) which are used to keep temperature of fired materials at $1,300^{\circ}C$. Design variables were numbers of inlets and outlets, distance between floor and lower HP ($h_1$), distance between lower HP and fired materials ($h_2$), distance between fired materials and upper HP ($h_3$), temperature of HP, numbers of HP and distance between HP. The numbers of inlets and outlets were determined so that nitrogen gas formed a laminar flow for efficient discharge. All other design variables were determined so that temperature of fired materials is as uniform as possible near $1,300^{\circ}C$. Chambers were produced and temperature was measured at 21 points using thermocouples. The largest deviation from $1,300^{\circ}C$ was less than ${\pm}2.2^{\circ}C$.

• KSBB Journal
• /
• v.9 no.5
• /
• pp.483-491
• /
• 1994

It is known that a key limiting factor to the use of ultrafiltration membranes is that of membrane fouling, which has been a major cause of permeate flux reduction. In this work, the effects of several factors (operating time, protein concentration, temperature and pH, etc.) influencing permeate flux during ultrafiltration of gelatin, casein and bovine serum albumin using a hollow fiber membrane(M. W. 10,000 cut off) reactor have been examined. The permeate flux of gelatin solution was maintained almost constant during the operation up to 6 hours, but those of casein and albumin solutions were decreased to 50% and 43% of initial value after an operation time of 60min. The permeate flux with increasing concentration and temperature of protein solutions increased, but the permeate flux showed a minimum value near the isoelectric point of proteins. The permeate fluxes of protein solution were enhanced by a temperature increase and pH control. Also, it is proposed that fouling can be decreased by the pretreatment of insoluble proteins with enzymes.

• Development and Reproduction
• /
• v.1 no.2
• /
• pp.141-156
• /
• 1997

1992년 1월부터 12월까지 1년간에 걸쳐 전북 군산, 선연리 조하애에서 채집된 개량조개, Mactra chinensis Philippi를 대상으로 생식세포 발달과 생식소 발달양상을 조사하기 위해 토과형 전자현미경으로 미세구조 변활르 관찰하였고, 정확한 산란기를 규명하기 위해 조직학적으로 생식주기를 조사하였다. 개량조개는 장웅이체이다. 난황형성과정은 난모세포의 발달정도에 따라 다르게 나타나고 있다. 전난황형성기 난모세포질 내에서는 핵주변 구여게 골지장치와 수많은 공포들 및 미토콘드리아들이 출현하고 있는데 이들은 차후, 지방적 형성에 관여한다. 난황형성전기 난모세포에서는 지방적 및 지질과립들이 핵막 근처에서 출현하여 피질층쪽으로 분산되는 반면, 같은 발달단계의 난모세포질의 피질구역에서는 피질과립들 (단백질성 난황과립)이 처음으로 생성되어 난황막 근처의 피질층에서 핵주변 구역쪽으로 분산 분포된다. 난황형성후기 난모세포에서는 세포질 내의 골지장치, 공포, 미토콘드리아, 그리고 조면소포체들이 자율합성에 의해 난황과립 형성에 관영하고 있다. 반면, 외인성 물질들인 지질형태의 과립들, 단백질성 물질 및 다량의 글리코겐 입자들이 생식상피 낸에서 출현하고 있는데, 이들 물질이 생식상피에서 난황막 구조물인 미세융모를 통해 난황형성 후기 난모세포의 난질 내로 통과해 들어가는 현상이 관찰되었다. 이와 같은 현상은 난황성성이 일어날 때에 hterosynthesis가 일어나고 있음을 시사한다. 완숙난모세포의 난경은 약 50-60 \mu m이고, 완숙정자 두부의 길이는 대략 3 \mu m이며, 미부의 길이는 약 30 \mu m정도이다. 정자 미부편모의 axoneme은 중앙의 2개의 미세소관(microtubule)과 주변에 위치한 9개의 2중 미세소관 (microtubule)으로 구성되어 있다. 본 종의 산란기는 5월에서 9월 중순에 걸쳐 일어나는데, 주산란시기는 해수수온이 22 \circ C 이상으로 상승하는 6, 7월이다. 따라서 1년에 산란 (번식)시기가 한번 일어나고 있음을 알 수 있다. 생식 주기는 초기활성기 (1-2월), 후기활성기 (2-4월), 완숙기 (4-9월), 산란기 (5-9월) 그리고 퇴화 및 비솰성기 (6-12월)의 연속적인 5단계로 구분할 수 있었다. 재생산에 가담할 수 있는 암, 수개체들의 군성숙도(%)를 조직학적으로 조사한 결과, 각장 3.5-3.9cm 범위의 개체는 55.5%이었고, 5cm 이사인 개체들은 재생산에 100% 참여하였다. 본 종의 암, 수개체들은 만 1년부터 재생산에 가담하는 것으로 추정된다.

• Spatial Information Research
• /
• v.21 no.4
• /
• pp.83-89
• /
• 2013

Recently various contents have been produced using the techniques that require high-performance computing process. A lot of services have been being producted as AR(Augmented Reality) service being combined with mobile information service that a moving user search various information based on one's location with. Mobile information service has a characteristic that it needs to get new information according to the location an user moves to. The characteristic requires a lot of communications when user search information moving to a different location. In order to make up for this drawback, we propose a prefetching technique based on speed and viewing angle in this paper. Existing prefetching techniques retrieve the following location of users considering moving speed and direction of the users. The data showed on the screen in AR is limited by the viewing angle of the mobile device. Due to the problems we discussed above, existing prefetching techniques have a demerit that they retrieve a lot more data than needed actually. We propose more efficient way of retrieving data with AR using the viewing angle of the mobile device. The method we propose reduces retrieval of unnecessary location using the users' speed, direction and viewing angle. This method is more efficient than the existing ways of retrieval because we don't need as many data.

• Membrane Journal
• /
• v.21 no.4
• /
• pp.360-366
• /
• 2011

The effect of cross-flow velocity and transmembrane pressure (TMP) on membrane fouling was observed from pilot-scale operation of thermophilic anaerobic membrane bioreactor (AnMBR) treating food waste leachate. It was found that fouling rate was reduced significantly as cross-flow velocity increased at constant TMP mode of operation while this effectiveness was more pronounced at lower TMP. Higher TMP resulted in less permeable fouling layer possibly due to compressibility of foulant material on membrane surface. Particle sizes of membrane concentrate ranged from 10 to $100{\mu}m$, implying that shear-induced diffusion enhance back transport of these particle sizes away from the membrane effectively. From the continuous operation of AnMBR, it was confirmed that shear rate played an important role in the reduction of membrane fouling. Membrane autopsy works at the end of operation of AnMBR showed clearly that both organic and inorganic fouling were significant on membrane surface. Surface shear by cross-flow velocity was expected to be less effective to remove irreversible fouling which can be mainly caused by the adsorption of organic colloidal materials into membrane pores.