• Tribology and Lubricants
• /
• 제34권2호
• /
• pp.49-54
• /
• 2018

Hydraulic reciprocating seal has been widely used to prevent fluid leakage in hydraulic systems. Also, hydraulic reciprocating seal plays a significant role to provide lubricant film at contacting interface to minimize tribological problems due to sliding with counter material. To predict lifetime of hydraulic reciprocating seal, quantitative understanding of wear characteristics with respect to operating conditions such as normal force and sliding speed is needed. In this work, effect of sliding speed on wear of polyurethane (PU) hydraulic reciprocating seal were experimentally investigated using a pin-on-disk tribo-tester. The wear characteristics of PU specimens were quantitatively determined by comparing the confocal microscope data before and after test. It was found that the wear rate of PU specimens decreased from $4.9{\times}10^{-11}mm^3$ to $1.1{\times}10^{-11}mm^3/Nm$ as sliding speed increased from 120 mm/s to 940 mm/s. Also, it was observed that the friction decreased slightly as the sliding speed increased. Improvement of lubrication state with increasing sliding speed was likely to be responsible for this enhanced friction and wear characteristics. This result also suggests that decrease in sliding distance between PU elastomer and counter materials at lower sliding speed is preferred. Furthermore, the quantitative assessment of wear characteristics of PU specimen may be useful in prediction of lifetime of PU hydraulic reciprocating seal if the allowed degree of wear for failure of the seal is provided.

• 수산해양기술연구
• /
• 제47권3호
• /
• pp.267-272
• /
• 2011

The behavior of abrasive wear on counterpart roughness of glass fiber reinforcement polyurethane resin (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The friction coefficient, cumulative wear volume and surface roughness of these materials against SiC abrasive paper were determined experimentally. The major failure mechanisms were lapping layers, ploughing, delamination, deformation of resin and cracking by scanning electric microscopy (SEM) photograph of the tested surface. As increasing the counterpart roughness the GF/PUR composites indicated higher friction coefficient. The surface roughness of the GF/PUR composites was increased as the sliding velocity was higher and the counterpart roughness was rougher in wear test.

• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.80-84
• /
• 2009

The Plasma Transferred Arc (PTA) overlay welding method is lately introduced as one of the most useful surface overlay method of the engine component. In this paper, the overlay welding on the SNCrW heat resisting alloy was conducted by the PTA overlay welding process using the super alloy powder. The characteristics of the overlay layers were investigated through the metallurgical and abrasive test. Experimental results showed that the overlay on the SNCrW heat resisting alloy surface was successfully made without hot cracking. The friction wear characteristics of the Co-base Stellite 6 overlayer were most superior. However the abrasive wear characteristics were most inferior in the Co-base Stellite 6 overlayer.

• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.171-176
• /
• 2012

So far, carbide insert production technology was carried out using a diamond grinding wheel. This production technology has problem that raise production costs and decrease in productivity. The SIDE PRESS method to solve this problem have been developed. In this paper, the machining characteristics of lateral chip breaker turning inserts produced by the SIDE PRESS method was studied. The cutting force and the resulting surface roughness were measured at various cutting conditions. The experimental results indicate that the chip breaker inserts of three-dimensional geometry is the best cutting performance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.113-118
• /
• 1994

An experimental investigation on the wear of alumina grinding wheel is presented. The experiments consist of the measurements of fracture strength of the abrasive grains, grinding forces, and the area of wear flats of grinding wheels. Microscopic examinations of abrasive grains were also carried out to observe the progress of wheel wear. the results show that the 32A grain, which has relatively lower fracture strength, wears out faster than 5SS and 5SG. The wheel wear occurs much faster in wet grinding than in dry grinding. It has also been found that the grinding forces increase logarithmically with increasing wear flats.

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.160-165
• /
• 1999

In surface grinding, the conditions of the grinding wheel give a significant effect on the ground workpieces comparing with other metal removal provesses. In this paper, to assist the development, a non-contacting optical method by the laser beam is introduced. The in-process measurement of scattering intensities has been made during surface grinding processes and the surface textures of wheel working surfaces are captured. Also, in order to determine the dressing time monitoring method of a grinding wheel, a three-dimensional computer simulation of the grinding operation has been attempted based on the contact mechanism and the surface-shaping system between the grinding wheel and the workpiece. The optimal dressing time is determined by the amount of the grain wear and work surface roughness.

• 수산해양기술연구
• /
• 제46권4호
• /
• pp.495-502
• /
• 2010

The effect of load and sliding speed on abrasive wear characteristics of glass fiber/polyurethane (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The friction coefficient, cumulative wear volume and surface roughness of these materials against SiC abrasive paper were determined experimentally. Experimental results showed that the surface roughness of the GF/PUR composites was increased as applied load was higher in wear test. The cumulative wear volume tended to increase nonlinearly with increase of sliding distance and depended on applied load and sliding speed for these composites. It could be verified by scanning electric microscopy (SEM) photograph of surface tested that major failure mechanisms were lapping layers, ploughing, delamination, deformation of resin and cracking.

• 한국재료학회지
• /
• 제21권6호
• /
• pp.334-340
• /
• 2011

Saw wires have been widely used in industries to slice silicon (Si) ingots into thin wafers for semiconductor fabrication. This study investigated the microstructural and mechanical properties, such as abrasive wear and tensile properties, of a saw wire sample of 0.84 wt.% carbon steel with a 120 ${\mu}M$ diameter. The samples were subjected to heat treatment at different linear velocities of the wire during the patenting process and two different wear tests were performed, 2-body abrasive wear (grinding) and 3-body abrasive wear (rolling wear) tests. With an increasing linear velocity of the wire, the tensile strength and microhardness of the samples increased, whereas the interlamellar spacing in a pearlite structure decreased. The wear properties from the grinding and rolling wear tests exhibited an opposite tendency. The weight loss resulting from grinding was mainly affected by the tensile strength and microhardness, while the diameter loss obtained from rolling wear was affected by elongation or ductility of the samples. This result demonstrates that the wear mechanism in the 3-body wear test is much different from that for the 2-body abrasive wear test. The ultra-high tensile strength of the saw wire produced by the drawing process was attributed to the pearlite microstructure with very small interlamellar spacing as well as the high density of dislocation.

• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.102-108
• /
• 2015

In this research, we experimentally investigated the sealing performance of elastomeric rotary lip seals for washing machines. In general, NBR is used as a material for elastomeric rotary lip seals in washing machines, but the mixing formula of the rubber material can affect the sealing performance. In this study, we manufactured rotary lip seals using three kinds of NBRs with a different mixing formula, and examined the sealing performance using an acceleration test mode. The results of an SEM investigation into the surfaces of three kinds of specimens showed a much smaller wear volume and better sealing performance for the specimens with smaller particle sizes of mixing composition than for the specimen with the larger. Repeated deformation and recovery by the shaft-to-seal eccentricity on rotation were shown to cause a phase difference in the rubber material, and we measured the recovery ratio to find the influence of this phase difference on the sealing performance. As another method for checking the phase difference, we also measured tan ä, and a lower tan ä was revealed as the recovery ratio increased for each specimen. Specimens with a higher recovery ratio (lower tan ä) were shown to have a better sealing performance. Consequently, specimens with a smaller particle size in the mixing composition had a better sealing performance because they show a higher recovery ratio.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.73-79
• /
• 2002

상온 공기분위기에서 두 가지 형태의 스프링에 대한 연료봉 피복관의 마멸실험을 수행하였으며 다음과 같은 결론을 얻었다. (1) 가장 큰 마멸부피는 스프링 형상이 오목할 경우 틈이 존재할 때 발생하였으며, 형상이 볼록한 경우에는 접촉하중이 존재할 때 마멸부피가 크게 나타났다. (2) 접촉형상이 오목한 형태로 연료봉을 감싸고 있는 경우, 마멸입자의 방출은 다소 어렵게 되며 이에 따라 마열거동은 표면에서 생성되는 마멸입자가 외부로 방출되는 용이성에 따라 최종적으로 마멸부피는 결정된다. (3) 볼록한 형상의 스프링의 경우, 충격마모에 대하여 저항성을 보였으나, 접촉하중이 존재할 경우 높은 마멸량을 보이고 있다. (4) 오목한 형태의 스프링 조건에서 축 방향의 마멸보다는 횡 방향의 마멸량이 더 낮게 나타났다. 이것의 주된 원인은 오목한 형태의 스프링이 충격하중에 있어 가이드역할을 할 가능성이 있는 것으로 나타났다. 또한, 양 방향 모두 마멸입자의 고착 흔적이 나타났으나 횡 방향의 경우 연삭에 의한 경향이 보다 뚜렷이 나타났다.