• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.75-80
• /
• 2008

Biodiesel fuel(BDF) can be effectively used as an alternative fuel in diesel engine. However, BDF may affect the performance and exhaust emissions in diesel engine because it has different physical and chemical properties from diesel fuel such as viscosity, compressibility and so on. To investigate the effect of injection timing on the characteristics of performance and exhaust emissions with BDF in IDI diesel engine, it was applied the BDF derived from soybean oil in this study. The engine was operated at seven different injection timings from TDC to BTDC $12^{\circ}CA$ and six loads at a single engine speed of 1500rpm. When the fuel injection timing was retarded, better results were showed, which may confirm the advantages of BDF. The simultaneous reduction of smoke and NOx was achieved at some fixed fuel injection timings of an IDI diesel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.188-194
• /
• 2005

The direct injection diesel engine is one of the most efficient thermal engines. For this reason DI diesel engines are widely used for heavy-duty applications. But the world is faced with very serious problems related to the air pollution due to the exhaust emissions of diesel engine. So, that is air pollution related to exhaust gas resulted from explosive combustion should be improved. Exhaust Gas Recirculation(EGR) is a proven method to reduce NOx emissions. In this study, the experiments were performed at various engine loads while the EGR rates were set from $0\%$ to $30\%.$ The emissions trade-off and combustion of diesel engine are investigated. The brake specific fuel consumption rate is very slightly fluctuated with EGR in the range of experimental conditions. The ignition delay increased with increasing EGR rate. The maximum value of premixed combustion for the rate of heat release is increased with increasing EGR rate. NOx emissions are decreased with increasing EGR rate at high load and high speed. It was found that the exhaust emissions with the EGR system resulted in a very large reduction in oxides of nitrogen at the expense of higher smoke emissions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.181.1-181.1
• /
• 2010

기후변화의 주요인이 되는 온실가스 감축을 목표로 화석연료를 대체하기 위한 대체 에너지 개발을 위한 많은 노력이 진행되고 있다. 풍력 에너지와 같은 신재생에너지는 이러한 하나의 해결 수단이 될 수 있으며 풍력 에너지 사업의 활성화를 위해서는 정확한 풍력 정보 제공이 우선이다. 풍력-기상자원지도는 풍력 발전에 유용한 정보 제공을 위한 목적으로 중규모 수치 모델을 이용하여 작성된다. 본 연구에서는 중규모 수치 모델의 정확도 향상을 위한 자료동화 방법으로써 Four-Dimensional Data Assimilation (FDDA) 방법을 이용한다. 풍력-기상자원지도는 공간분해능 1 km 해상도로 개발된다. 풍력-기상자원지도는 1998-2008년까지의 평균적인 상태에 대하여 모의를 하기 위하여 통계적인 방법으로 11년 기간의 평균과 유사한 기간을 선정하였다. 풍력-기상자원지도는 연 평균, 월 평균 풍속과 주 풍향, 주풍향 발생 비율 등의 정보를 제공한다. 우리나라 풍속의 평균 분포는 내륙 산악지역, 남해안, 제주도에서 강풍이 발생하며 주 풍향은 대체로 북서풍이다. 주 풍향의 발생비율은 산악 지역과 남 동해안에서 높아 풍력 발전의 최적지 정보를 제공한다. 1 km 해상도의 모델과 관측의 오차는 서해안 등의 해안지역보다 강원 산악지역에서 오차가 더욱 증가하였다. 이러한 산악 지역의 오차는 복잡한 지형에서는 1km 미만의 수 백 m 해상도 수치모의가 필요함을 지시한다. 따라서 본 연구에서는 WRF-LES 모형을 이용하여 333m 해상도의 기상자원지도를 개발한다. 333m 해상도의 자원지도 영역은 강원도 지역에 대하여 모의되었다. 333m 해상도의 풍속 분포는 1km 해상도의 풍속 분포와 비교하였을 때 풍속의 분포가 보다 세밀하게 표현되었다. 정량적인 검증을 하였을 때 관측소에 따라 차이는 있었으나 1km 해상도에서 과대 모의된 풍속의 분포가 현저히 개선이 되었으며, 시간적인 경향도 잘 일치함을 보였다.

• Clean Technology
• /
• v.22 no.4
• /
• pp.286-291
• /
• 2016

In this study we made fuel pellet from miscanthus biomass and investigated changes of physiological characteristics and electricity consumption of pelletizing process in comparison with fuel pellet made of pine sawdust. We also examined combustion characteristics including ash content and clinker forming ratio with fuel pellet made of mixing with micanthus biomass and lime powder. Bulk density of ground-miscanthus and pine sawdust were $158g\;L^{-1}$ and $187g\;L^{-1}$, respectively. Bulk density of ground miscanthus was lower than that of pine sawdust, but increased to $653g\;L^{-1}$ after pelletizing, which was similar to $656g\;L^{-1}$ of pine sawdust pellet. Moisture content in raw miscanthus and ground miscanthus were 17.0% and 11.8%, respectively. Moisture content in ground miscanthus was similar to that of pine saw dust and decreased to 6.73% after pelletizing, which was 7.7% lower than that of pine sawdust pellet. Although $27kWh\;ton^{-1}$ were required for compaction press that was an additional process in miscanthus pelleitizing, total required electricity was $193kWh\;ton^{-1}$ which was similar to $195kWh\;ton^{-1}$ of pine sawdust pellet pelleitizing. Pellet durability and pelletizing ratio of miscanthus were 98.0% and 99.7%, respectively, which were similar to 98.1% and 99.4% of pine sawdust pellet. When lime mixing ratio increased, ash melting degree and clinker forming ratio of miscanthus pellet increased. While higher heating value and clinker forming ratio of miscanthus pellet decreased.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.953-960
• /
• 2019

The Miller cycle is a diesel engine that has been developed in recent years that it can reduce NOx and improve fuel consumption by reducing the compression ratio through intake valve closing (IVC) time control. The Miller cycle can be divided into the early Miller method of closing the intake valve before the bottom dead center (BDC) and the late Miller method of closing the intake valve after the BDC. At low speeds, the late Miller method is advantageous as it can increase the volumetric efficiency; while at medium and high speeds, the early Miller method is advantageous because of the high internal temperature reduction effect due to the expansion of the intake air during the piston lowering from IVC to BDC. Therefore, in consideration of the ef ects of the early and late Miller methods, it is necessary to adopt the most suitable Miller method for the operating conditions. In this study, a two-stage turbo charge system was applied to four-stroke engines and the process of enhancing the Miller effect through a reduction of the intake and exhaust valve overlap as well as the valve change adjustment mechanism were considered. As a result, the ef ects of fuel consumption and Tmax reduction were confirmed by adopting the Miller cycle with a two-stage supercharge, a reduction of valve overlap, and an increase of suction valve lift.

• Analytical Science and Technology
• /
• v.10 no.3
• /
• pp.179-186
• /
• 1997

This study was carried out to improve the analytical method for determination of germanium in plants by atomic absorption spectrometry with graphite furnace. For the decomposition of plant samples, the mixed acid of $HNO_3+HClO_4+H_2SO_4$(10 : 4 : 1, v/v) was used. Under this condition, time requirement for the decomposition was 4~5 days and recovery rate was more than 98%. Solution for filling up to constant volume after decomposition was 0.1M acetic acid-sodium acetate. Detection limit for determination of germanium was 0.02 ppm by atomic absorption spectrometry with graphite furnace and argon gas. These results were corresponded with the above-mentioned research projects for improving the determination method of germanium in plants.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2008.04a
• /
• pp.161-166
• /
• 2008

This paper searched through mixture ratio response test whether exert effect that is some in part load performance of engine according to inlet valve angle in gasoline engine. Engines that inlet valve angle is narrow decreased quantity of NOx among exhaust gas than engine that inlet valve angle is wide, and ignition timing was retard, and fuel consumption improved a little. That quantity of NOx among exhaust gas decreases and ignition timing was retard can judge that fast burning occurred. Fast burning can decrease output decline and misfire that can happen at lean burning. Can be judged by thing which engine's combustion performance improves if inlet valve angle is narrow if examine test result.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.1225-1234
• /
• 2013

According to the importance of greenhouse gas emissions, it grows day by day, the goverment is promoting to prepare the specific policy implementation to enhance building energy-saving design standars as the development agenda. In this study, the statistical analysis was performed by Descriptive statistics, Regression analysis, and Hypothesis testing to collect to generate and storage energy usage data in real time to settle parameter setting to affect energy consumption under energy-guzzling apartment not single building. This study is expected to be utilized as the basis for the optimum energy-saving design of the future of the building or facility energy costs rise and the demand for energy-efficient and stable management.

• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.1-7
• /
• 2013

In this study, simulation work of HCNG refueling system was performed. The hydrogen was produced from steam reforming process by natural gas. The conversion of natural gas is increased as SCR is increased. but it was no significant difference more than 3 of SCR and fuel throughput is increased as GHSV is increased. Both conversion and fuel throughput levels was optimized when the $1700h^{-1}$ of GHSV. CNG was compressed from low pressure natural gas. For the mixing of $H_2$ and CNG is mixed with the high pressure conditions such as 400bar of $H_2$ and 250bar of natural gas. Single-stage compression was required more power than multi stage. So, multi stage compression was suggested for high pressure compression. We calculated the intermediate pressure to minimize total required power of compressors. The intermediate pressure for $H_2$ and natural gas were derived at 61 and 65 bar, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.197-197
• /
• 2010

음식물쓰레기의 삼성분은 수분, 휘발분, 회분이며 이들이 차지하는 비율은 계절, 지역별로 다소 상이하지만 수분 약 80%, 회분3%, 휘발분 17%이다. 음식물쓰레기 전처리과정으로 이물질제거, 탈수공정이 있으며 탈수공정에서 다량의 탈리액이 발생한다. 본 연구에서는 탈리액을 데칸타를 이용하여 1차로 원심분리하여 고.액 분리한 액을 실험대상으로 하였다. 실험대상 탈리액의 물성은 BOD 78,800[mg/l], COD 41,000[mg/l], 부유물질 25,900[mg/l], 총질소 928[mg/l]이었다. 탈리액에는 기름성분(육류, 식용유등), 입자상물질등이 포함되어 있으며 이들은 난분해성 유기물질로, 이를 제거하는데 기존의 처리방법으로 많은 어려움이 있어 주요한 수질오염 발생원이 되고 있다. 예를들면 하수처리장 폭기조 수면에 유막을 형성하여 산소공급을 방해함으로 미생물번식을 방해하는 요인이 된다. 본 연구는 음식물쓰레기 탈리액의 수분, 고형분, 유분으로의 삼상분리에 관한 것이다. 유분은 에멀젼형태로 안정되게 수층에 분산되어 존재한다. 미세기포를 이용한 부상법의 경우 미세기포 표면과 유분의 화학적친화력이 낮아 기포표면에 유분이 잘 부착되지 않으며, 원심분리 방법만으로는 유분 분리효율이 낮고, 추출에 의한 분리시 추출액이 다량 소요되고 처리시간이 길며 추출액 비용이 많이 소요된다. 탈리액을 유분, 슬러지, 수분으로 분리하면 환경오염을 일으키는 주요성분을 신재생에너지 원료로 활용할 수 있다. 유분의 주성분이 동식물성 유지이므로 전처리시 산촉매를 이용 수분과 유리지방산을 제거하고 염기성촉매를 이용하여 전이에스테르화 반응을 거치면 바이오디젤인 FAME과 글리세롤으로 변환하므로 글리세롤을 분리하면 바이오디젤을 얻을 수 있다. 슬러지는 입자상 물질로 착화가 잘 되고 건조하면 발열량이 높으며 중금속등에 오염되지 않아 청정연료로 활용이 가능하다. 실험실에서의 탈리액 삼상분리방법은 다음과 같다. 탈리액 30ml당 추출액으로 노말헥산을 1ml를 가한 다음 플라스크에서 $80^{\circ}C$로 가열 후 방냉한다. 가열중 노말헥산의 손실을 방지하기 위하여 증발가스를 콘덴서에서 응축하여 플라스크로 재순환한다. 탈리액을 플라스크에서 꺼내어 원심분리기 rack에 300-400g씩 병에 각각 넣고 4,000rpm으로 30분간 운전한다. 탈리액은 상부로부터 유분층, 미세입자층, 수층, 슬러지층으로 분리된다. 각 층의 계면에서 2종의 성분이 약간 섞일 수 있다. 유분을 분리한 후 유분층 잔존물과 미세입자층, 수층 상층부의 혼합물을 취하여 50g씩 병에 넣고 3,500rpm으로 10분간 운전한 후 유분을 분리한다. 마지막으로 미세입자층만을 3,500rpm으로 10분간 원심분리한 후 유분을 따로 분리한다. 얻어진 유분은 rotary evaporator에서 $120^{\circ}C$로 가열하여 유분과 노말헥산을 분리하며 분리효율을 제고하기 위하여 감압하에서 운전한다. 분리된 유분의 고위발열량이 9,450[Kcal/kg]이었으며 원소분석 결과 탄소 74.7%, 수소 12.55%, 질소 0.08%, 유황분 0.0003%이었다. 분리된 유분의 양은 계절별로 시료별로 다르며 가을철에는 1.6-1.9%, 여름철은 1.0-1.3%이었다. 분리된 슬러지로부터 Hg, As, Cr, Cd, Pb 중금속 성분이 검출되지 않았으며 수분 2.8%, 휘발분 76.85%, 회분 7.52%, 고정탄소 12.83%이었고 원소분석결과 탄소 45.25%, 수소 7.46%, 질소 5.05%, 산소 34.39%, 유황분 0.33%이었으며 저위발열량은 4,480[Kcal/kg]이었다. 분리된 슬러지 양은 11-19% 이었다.