• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.317-317
• /
• 2008

기존의 초음파 노즐은 단판액츄에이터형 초음파 노즐을 사용하여 연체 연료를 분사하였다. 하지만 단판액추에이터형 초음파 노즐은 300V이상의 고전압을 필요로 하여 소비전력이 높은 단점을 가지고 있다. 하지만 적층액츄에이터형 초음파 노즐은 저전압 구동이 가능하여 낮은 소비전력을 가지며, 단판액츄에이터헝 초음파 노즐보다 우수한 분사특성을 가지고 있는 장점이 있다. 또한 공진형 인버터를 사용하여 초음파 노즐을 구동하는 경우 노즐의 구동 전압을 공진에 의하여 쉽게 얻어질 수 있는 장점과 구동 스위치에 가해지는 전압의 크기가 상대적으로 작게되므로 인버터 구동에 저전압 MOSFET를 사용함으로써 도통손실의 저감 및 구성회로의 저압화 등에 유리한 이점이 있다. 본 연구에서는 적층액츄에이터형 초음파노즐을 개발하고 그에 따른 공진형 인버터를 설계하여 적층엑츄에이터형 초음파 노즐의 분사 시스템을 제안 한다. 또한 실제 액체연료인 경유를 분사하여 전기적특성과 분사특성을 조사한다.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.17-23
• /
• 1998

A simplified experiment was performed to figure out the atomization characteristics of highly viscous liquid of rice-bran oil by applying ultrasonic energy to improve the atomization of spray droplets. A spray system, an ultrasonic system, and three kinds of pintle-type nozzles(pin-edge angle: 5 , 10 , 15 ) were manufactured. To investigate the effects of ultrasonic energy on the atomization of a highly viscous liquid, a phase doppler particle analyzer was used for the measurement and calculation of spray droplets data. Nozzle opening pressures were chosen of 3 levels, i.e, 10, 13, 16 MPa. As a result, it could be concluded that the ultrasonic energy was effective to improve the spray atomization when applied to the fuel by means of 3 different nozzles because of the effects of the liquid fuel cavitation and relaxation between molecules caused by ultrasonic energy. The improvement rate of the spray atomization by the ultrasonic spray atomization by the ultrasonic spray compared with the conventional spray was about 10% increase in the case of pintle type nozzles. With the increase of pin-edge angles the distribution lines by nozzle opening pressures are declined for both conventional and ultrasonic sprays. This means that the increase of the pin-edge angle improves the atomization of sprays.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.57-65
• /
• 2008

The atomization phenomena and spray characteristics of drum type rotary atomizer using centrifugal force from high rotational speed of gas turbine engine shaft were studied through rotary atomizer modeling analysis and experimental method. A test rig for rotary atomization that has range of $5,000{\sim}40,000\;rpm$ was used to make similarity for high speed rotating shaft. Spray visualization methodology and Phase Doppler Anemometry were also used to investigate the atomization mechanism and spray characteristics. We found that the rotating fuel spray has unique breakup process and we have to make breakup point earlier through increasing rotating speed to improve atomization performance.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.3
• /
• pp.41-47
• /
• 2013

This study was carried out to improve the design of fuel injection nozzle for marine medium speed diesel engine. For this purpose, fuel injection nozzle was modeled and simulated using CATIA V5R19 and FLUENT & MSC Nastran. Analyses of flow and heat transfer, respectively, were performed to find the optimal design of fuel injection nozzle. As the results, big pressure drop, which may lead to cavitation damage, was occurred at inlet of fuel injection hole with diameter 0.3mm. Furthermore, it was confirmed that the increase of mean temperature of fuel injection nozzle was almost a half in comparison with that of fuel injection nozzle tip.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.12
• /
• pp.1108-1114
• /
• 2007

The effect of oxidizer injection angle on the combustion characteristics of end-burning hybrid combustor is numerically investigated. Besides the previously studied parameter(injector arrangement, port diameter and O/F ratio), three different injection angle are considered: parallel angle to fuel surface(Case 1), +30 degree inclined angle toward the fuel(Case 2) and 30 degree inclined angle toward the nozzle(Case 3). It is found that Case 2 has the best mixing pattern in the upstream area but has the worst combustion efficiency since non negligible amount of unburned fuel is expelled from the nozzle. In contrast, though Case 1 and Case 3 showed relatively low mixing effect than the Case 2, they had high combustion efficiency. The comparison of numerical results between Case 1 and Case 3 demonstrate that no major difference is encountered, however, Case 1 is expected to have the best combustion efficiency due to the low residence time of the Case 3 injector which heads toward the nozzle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.6-6
• /
• 1998

항공기용 가스터빈 및 일반적인 산업용 분무시스템에서는 많은 양의 분사액체를 미립화 시키고 시스템의 연속적인 운전과 유지를 편리하게 하기 위하여 여러 개의 분사노즐을 열로 설치하여 동시에 분사하도록 하고 있다. 이렇게 동시에 분사할 경우, 노즐간에 거리가 충분히 크지 않으면 개별적으로 분사된 분무들이 서로 합해져서 하나의 연합된 분무군이 형성된다. 이렇게 Two element에 의해서 형성된 spray는 공급압력이 증가함에 따라 관성력이 증가하게 되어 중심부분에서 액막 혹은 액적상태로서 충돌이 발생하여 복잡한 분무특성을 가질 것이다. 따라서, 연합된 분무군의 특성을 이해하는 것은 응용의 측면에서 매우 중요하다고 할 수 있다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.335-340
• /
• 2005

A study on the variation of combustion characteristics by injector geometries was conducted. Coaxial swirl injectors were used. Existence of swirl chamber and variation of a nozzle length become key parameters. Injectors were identified as open, closed and mixed type by existence of swirl chamber. Variation of nozzle length was made extruding the both nozzle along the axis while other design parameters remain the same. A uni-element combustor with ablative material liner and a water cooled nozzle made by oxygen free copper with outer stainless steel casing were used.

• Journal of the Korean Institute of Gas
• /
• v.25 no.6
• /
• pp.22-28
• /
• 2021

Combustion characteristics were examined experimentally for a swirl-stabilized double cone premixed burner nozzle used for industrial gas turbines for power generation. An original model and a variant with a different fuel injection pattern are tested to compare their combustion characteristics such as NOx, CO and stability in pressurized conditions with single burner-flame and in an ambient multi-flame conditions with multi-burners. Test results show that NOx emissions are smaller for the variant, whose number of fuel holes is reduced with the same total area of fuel holes, in ambient and pressurized single-flame conditions with single burner, which results from enhanced fuel/air mixing due to a higher penetration of fuel into the air stream. The multi-burnerflame test results show that NOx emissions are smaller for the variant due to reduced flame interactions, which, on the contrary, slightly reduces the stability margin. On-site test results fromin an actual power plants also show that NOx emissions are reduced for the variant, compared with the original one, which is in agreement with the lab test results stated above.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.251-253
• /
• 2017

Numerical study of air-blast type injector for low emission aircraft engines was conducted. Volume-of-fluids approach was used to track interface of fuel and air. Primary atomization of fuel stream was visualized, and thickness and mean velocity at the injector exit was calculated. Liquid fuel injected from fuel slots joined together as a thin film on preflimer surface, and interacted with swirling air. As instability on the fuel surface increased, separation of fuel as ligaments and droplets occured. The film thickness and velocity were used to as fuel injection boundary condition for reactive flow simulation. Primary reaction zone was formed in vicinity of the fuel nozzle, creating a stable flame inside the combustor.

• Journal of the Korean Institute of Gas
• /
• v.24 no.1
• /
• pp.49-55
• /
• 2020

Experimental investigations were conducted to understand the multi-staged combustion characteristics of a swirl-stabilized double cone premixed burner nozzle used for industrial gas turbines for power generation. Multi-staged combustion is implemented by injecting the fuel through the existing manifold of the side slots as well as through the apex of the cone with two fuel injection angles which are slanted or axial. NOx and CO emissions, and wall temperature distributions were measured for various fuel distributions and operating conditions. Results show that NOx emissions are decreased when the fuel distribution to the apex is 3% of the total amount of fuel, which is due to more uniform fuel distribution inside the nozzle, hence less hot spots at the flame. NOx emissions are rather increased when the fuel distribution to the apex is 8% of the total amount of fuel for axial fuel injection by occurrence of flash back in premixing zone of burner.