• Korean Chemical Engineering Research
• /
• v.51 no.3
• /
• pp.370-375
• /
• 2013

We analyze the effects of CO poisoning and air bleeding on the performance of a PEM (polymer electrolyte membrane) fuel cell stack fabricated using commercial MEA (membrane electrode assembly). Dynamic response data from the experiments on the performance of a stack are identified by obtaining steady-state gains and time-constants of the first-order system model expressed as a first-order differential equation. It is found that the cell voltage of the stack decreases by 1.3-1.6 mV as the CO concentration rises by 1 ppm. The time elapsed to reach a new steady state after a change in the CO concentration is shortened as the magnitude of the change in the CO concentration increases. In general, the steady-state gain becomes bigger and the time-constant gets smaller with increasing the air concentration (air-bleeding level) in the reformate gas to restore the cell voltage. However, it is possible to recover 87%-96% of the original cell voltages, which are measured with free of CO, within 1-30 min by introducing the bleed air as much as 1% of the reformate gas into the stack.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.1011-1016
• /
• 2008

Jet-A spray and combustion were numerically analyzed in annular type combustor model using KIVA3V. The combustor geometry have 6 dilute holes. Swirl effect and thermal NO were considered in this investigation to analyze mixing and combustion characteristics. Fuel vapor, flame temperature, NO generation were investigated for various spray angle. As increase of spray angle, Jet-A vapor appeared uniformly in primary zone and evaporation rate was increased. Mixing between fuel vapor and ambient gas was enhanced as increase of spray angle. As a result, high temperature region appeared widely and thermal NO generation rate was increased.

• Journal of the Korean Institute of Gas
• /
• v.15 no.3
• /
• pp.39-46
• /
• 2011

This study investigates the effects of the DME and n-Butane mixture and of the stratification on combustion characteristics of HCCI engine by chemical reaction calculation. First, the existing DME reaction scheme and n-Butane is combined to make new chemical reaction model, then validating the effectiveness of new scheme. Furthermore, this study verify the HCCI combustion characteristics according to the changes of DME and n-Butane mixture ratio, which shows different auto ignition characteristics. Finally, it confirms the effects of stratification of mixture fuel on the reduction of pressure rise rate.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.201-203
• /
• 2007

본 논문에서는, 연료전지 시스템의 기계적 주변장치 (MBOP)와 전기적 주변장치 (EBOP)의 최적 설계를 위해서 PEMFC 스택을 전기화학반응을 기초로 모델링한다. 모델링을 위해 기본적인 PEMFC의 구조와 동작 원리를 설명한다. 연료전지의 이론적 최고 전압인 평형전위를 깁스 자유에너지와 네른스트 방정식으로 유도한다. 전류밀도에 따른 전압 손실인 활성화, 저항, 농도 분극현상을 표현하기 위해서 수식을 유도한다. 수소가 이온화되지 못하고 산소극으로 넘어가서 발생되는 연료손실 및 내부전류와 지속적인 정역반응인 교환전류도 모델링된다. 평형전압에서 각 분극을 뺀 실제 운전 전압을 시뮬레이션하고, 유량과 압력에 따른 출력 특성을 시뮬레이션 한다. 부하변동 시 출력특성을 시뮬레이터와 실험결과로 비교한다.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.1
• /
• pp.49-53
• /
• 2007

The direct methanol fuel cell (DMFC) is a promising power source for portable applications due to many advantages such as simple construction, compact design, high energy density, and relatively high energy-conversion efficiency. In this work, an electrochemical methanol sensor for monitoring the methanol concentration in direct methanol fuel cells was fabricated using a thin composite nafion membrane as the electrolyte. We have analyzed the I-V characteristic of the fabricated methanol sensor as a function of methanol concentration, catalyst electrode and platinum(Pt) thickness. The fabricated sensor was analyzed by I-V measurement with various methanol concentration. When we measured the sensor characteristics with 10nm Pt and at 1V, the current value was $1.30{\times}10^{-6}A,\;1.96{\times}10^{-6}A\;and\;2.80{\times}10^{-6} A$ for three methanol concentration of 1M, 2M and 3M, respectively. When the methanol concentration was fixed at 2M, the current value of the fabricated device with Pt layers of 5, 10 and 15 nm thickness was $3.06{\times}10^{-6}A,\;1.96{\times}10^{-6}A\;and\;1.00{\times}10^{-6}A$, respectively. These results lead us to the conclusion that when the methanol concentration increases, the output current increases and when the catalyst electrode become thinner, the current increase more. It showed that, the thinner the catalyst electrode, the more electrochemistry become activation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1022-1027
• /
• 2011

A diesel engine works in high compression ratio due to injection of diesel fuel after compression of air. Therefore the engine has a high thermal efficiency, while nitrogen oxide is produced a lot in high flame temperature regions. In order to solve the problem this study HHO gas is added into the intake air of the industrial diesel engine. The test conditions are loads of 0%, 50% and 100% and engine speeds of 700 to 1900 rpm. The results show the maximum torque and pressure is increased, fuel consumption, smoke and CO emissions are decreased and NOx emission is remained at same level.

• Resources Recycling
• /
• v.20 no.5
• /
• pp.52-57
• /
• 2011

This study was conducted to examine the possibilities to utilize the mixture of domestic and organic wastes from B-city as a fuel. All types of mixing ratio for uncarried waste, sludge cake, and food waste were found 10 generate heating value with 6,000 kcal/kg, and in case of sludge cake the concentration of toxic substance produced was found to be decreased as air-fuel ratio and temperature were increased. It was noted that toxic gases such as CO, NOx, and SOx were observed below concentration of emission standard, and temperature inside the incinerator was stabilized at 2 of air-fuel ratio and 800$^{\circ}C$. It was observed that a heating value of 6000 kcal/kg generated using RDF(Refuse Derived Fuel) was appropriate to utilize a fuel if a complete combustion was attained.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.23 no.3
• /
• pp.51-59
• /
• 2015

Livestock sludge contains high concentration of organic matter and some heavy metals. In case of discharging into the sea, it might have negative effects in the environment. In this study thermal hydrolysis reaction was applied for livestock sludge to determine the fuelization possibility and obtain the best operation conditions. Livestock sludges were thermally hydrolyzed at temperature range $170{\sim}210^{\circ}C$ in sealed high-temperature reactors. Liquid products and dewatered cakes were analyzed. The operation at $190^{\circ}C$ was found to be best effective condition. High heating value and low heating value were 5,050 kcal/kg and 4,740 kcal/kg, respectively. Therefore, fuelization of livestock sludge using thermal hydrolysis reactor is found to be highly effective.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.1
• /
• pp.146-151
• /
• 2013

This paper reveals the performance decrease and recovery of PEMFC when the contaminated fuel gas and air source with sulfur impurities such as hydrogen sulfide and sulfur dioxide were simultaneously introduced to anode and cathode, respectively. Three different GDLs were fabricated with different carbon black and activated carbon to prevent an introduction of sulfur compound impurities into MEA. components. The severity of $SO_2$ and $H_2S$ poisoning was depended on concentrations(3 ppm - 10 ppm) of sulfur impurities. Especially, cell performance degradation rate was rapid when MEA fabricated with CN-2 GDL because it had little porosity on GDL surface. Moreover, the cell performance can be recovered up to 90%-95% only with neat hydrogen and fresh air feeding.. Conclusively, MEA fabricated with porous CN-1 GDL showed the best cell performance and recovery efficiency during exposure to poisoning condition by simultaneous sulfur impurities.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.4
• /
• pp.170-177
• /
• 2006

Optimum design of flow channel in the separation plate of Proton Exchange Membrane Fuel Cell is very prerequisite to reduce concentration over potential at high current region and remove the water generated in cathode effectively. In this paper, fully 3 dimensional computational model which solves anode and cathode flow fields simultaneously is developed in order to compare the performance of fuel cell with parallel and interdigitated flow channels. Oxygen and water concentration and pressure drop are calculated and i-V performance characteristics are compared between flows with two flow channels. Results show that performance of fuel cell with interdigitated flow channel is hi민or than that with parallel flow channel at high current region because hydrogen and oxygen in interdigitated flow channel are transported to catalyst layer effectively due to strong convective transport through gas diffusion layer but pressure drop is larger than that in parallel flow channel. Therefore Trade-off between power gain and pressure loss should be considered in design of fuel cell with interdigitated flow channel.