• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.7
• /
• pp.914-919
• /
• 2004

When the motor is rotating, the torque and rpm are varying as the loads or the driving status connecting through reduction units are changing. On the contrary, one can monitor the changes of the loads or the driving status in the manner of measuring motor torque and rpm. There is a torque measuring method using the strain gauge and bridge circuit. But, because this is the contact method, it has the life time which is dependent on rotating velocity and used time. So this system demands on replacement of some Parts or whole system itself for maintenance. And this system is also relatively big and expensive, requiring preceding annoying process. In this paper, we are going to suppose non-contact method to measure torque and rpm using the Hall effects sensor For this we have made the planetary geared reduction motor with Hall sensors and with the monitoring system. The monitoring system displays the sensing data(torque, rpm) and calculated data( power) and also has the network capability with Bluetooth protocol. Our solution is much more inexpensive ;md simple method to measure torque and rpm than before.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.1
• /
• pp.52.2-52.2
• /
• 2012

1438년 장영실은 경복궁 흠경각(欽敬閣) 내부에 자동물시계인 옥루(玉漏)를 제작하였다. 흠경각루(欽敬閣漏)는 수격식(水激式, 물의 흐름을 이용하여 수차를 운행하는 동력방식)으로 운영되는 것으로 중국의 수운의상대(水運儀象臺, 1092년경 제작)의 수격방식과 유사하다. 하지만 동력 방식을 제외한 내부 구조에 대한 것은 흠경각루의 외형모습인 가산 형태, 시보인형의 구성과 배치, 작동구조 등에 의해 결정된다. 장영실은 흠경각루의 내부 기어장치의 구성과 연결 등에 대해서 새로운 제작기술을 사용하였다. 우리는 수격식 동력 방식에서 내부 공간에 따른 각각 운행 장치들의 구성과 동력전달체계에 대하여 분석하였다. 또한 수차가 일정한 회전력을 갖도록 제어하는 천형(天衡) 장치에 대하여 고찰하였다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.746-747
• /
• 2015

전동기와 부하시스템은 직결, 혹은 커플링을 통하여 연결이 된다. 이때의 동력을 전달하는 커플링, 기어, 벨트 등의 특성에 따라 전달되는 토크의 특성이 달라진다. 본 논문에서는 동력 축과 부하 축을 기구적으로 분리가 가능한 영구자석 커플링을 적용한 구동 전동기-부하시스템에 축계 시스템 해석을 위하여 유한요소 해석을 통하여 비틀림 각도 변화에 따른 전달 토크를 얻고, 이를 활용하여 기구 해석 모델에 적용해 보고, 전동기-부하 시스템의 토크 변동 가능성에 대해 알아본다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.799-802
• /
• 2002

Continuously variable transmission(CVT) mechanisms considered here combine the functions of a K-H-V type differential gear unit and a V-belt type continuously variable unit(CVU). As combining the functions of a K-H-V type differential gear unit and a V-belt type CVU, 24 different mechanisms are presented. Some useful theoretical formula related to speed ratio, power flow and efficiency are derived and analyzed. These mechanisms have many advantages which are the decrease of CVT size, the increase of overall efficiency, the extension of speed ratio range, and the generation of geared neutral.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.1-9
• /
• 2004

In this paper, an efficient modeling method of Horizontal-Axis Wind Turbine(HAWT) system is proposed. This method Is based on representing a HAWT system as a multi-body system with several rigid bodies i.e. rotor blade, low/high speed shaft, gear system, md generator. Also, simulation software WINSIM is developed to evaluate performance of wind turbine system. Simulation results show that the proposed modeling method and simulation software are efficient and reliable.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.199-208
• /
• 2003

Continuously variable transmission (CVT) mechanisms considered here combine the functions of a K-H-V type differential gear unit and a V-belt type continuously variable unit (CVU). As combining the functions of a K-H-V type differential gear unit and a V-belt type CVU, 24 different mechanisms are presented. Some useful theoretical formula related to speed ratio, power flow and efficiency are derived and analyzed. These mechanisms have many advantages which are the decrease of CVT size, the increase of overall efficiency, the extension of speed ratio range, and the generation of geared neutral.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.55-60
• /
• 2020

As research and development of eco-friendly vehicles are expanding worldwide, additional devices of vehicles are reduced or deleted to increase the mileage, or research is being conducted to reduce weight. Among them, the multi-stage transmission that was applied to the internal combustion engine vehicle was deleted and replaced with a reducer, and the initial driving power is secured by increasing the torque through the control of the motor output value. However, since frequent motor speed change can result in a load increase, this study attempts to develop a compact and lightweight manual two-stage reducer with a general reducer structure. Therefore, a two-speed transmission with two gear ratio was designed by inserting a large gear and a small gear in a structure with a parallel shaft to connect the gears with a V-belt in the form of a parallel shaft reducer, and setting the gear ratio of the low and high gears respectively. In addition, power performance according to the rotational speed and load of the transmission was checked through a test, and the heat generation characteristics generated during driving were checked to verify the validity of the transmission.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.2
• /
• pp.437-444
• /
• 2010

The audio data have been communicated using analog methods or simple protocols. However, with the advent and improvement of various multimedia functions, many audio devices have been integrated into a mobile handset in which interconnection lines are very complicated. Conventional point-to-point connections such as $I^2S$ and PCM demand more power consumption whenever more devices are attached. In this paper, we design a common bus digital audio interface that communicates with only two wires and employs the clock gear method to reduce bus power consumption. The comparison results show that the proposed common bus connection can reduce more than 30% of power consumption as compared with point-to-point connection if more than three devices are connected.

• Journal of KSNVE
• /
• v.4 no.3
• /
• pp.264-272
• /
• 1994

동력을 발생하거나 이를 이용하는 대부분의 기계장치는 회전하는 축계 장치 를 갖고 있는데 이들은 중량을 갖는 회전체와 이것을 지지하거나 연결하는 강성축과 베어링으로 구성되므로 진동형태에 따른 고유진동수를 나타낸다. 그 결과 축계 장치 가 운전되는 동안 발생하는 기진력이 축계 강도를 초과하거나 진동수가 시스템의 공진점에 일치하던지 가까우면 이들 진동에 의해 축계 장치에 부착되어 있는 카프링, 감속기어, 지지베어링, 밀봉씰, 공정볼트 등이 이상마모 또는 피로파괴의 원인이 되므로 설계시나 운전중에 이에 대한 진동원인들을 PC를 이용하여 현장운전자들이 쉽게 규명할 수 있도록 개발하고 발생되는 진동문제를 효과적으로 해결할 수 있는 진동 저감장치를 몇 가지 소걔하였다. 국내에서 제작되는 선박, 자동차, 발전프랜트 또는 여기에 설치되는 엔진의 진동저감울 위해 이들 소프트웨어와 하드웨어들은 국내 관련기업의 현장기술 지도를 위해 여러차례 활용된 바 있으며 이를 이용하므로 써 축계진동 저감기술 자립은 물론 국산화 제품의 성능향상에도 크게 기여할 수 있다고 본다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.5
• /
• pp.407-413
• /
• 2014

The diesel engine and reduction gear combination is one of the common propulsion system in a naval vessel. Since the diesel engine has torsional vibration caused by reciprocating motion of the mass and gas pressure force of the cylinder, high cycle torsional fatigue can be occurred. Therefore, ROK navy restricts the maximum stress of the propulsion shaft according to MIL G 17859D. In this paper, the root cause for the failure of the diesel engine and reduction gear connecting shaft occurred in typical naval vessel is investigated based on the measured bending and torsional moment according to MIL G 17859D procedure.