• Journal of Korean Society of Transportation
• /
• v.18 no.4
• /
• pp.107-115
• /
• 2000

We suggest a method which solves the planar, two vehicle collision reconstruction problem. The method based on the Principle of impulse and momentum determines the pre-impact velocity components from Post-impact velocity components, vehicle Physical data and collision geometry. A novel feature is that although the impact coefficients such as the restitution coefficient and the impulse ratio are unknown, the method can estimate automatically the coefficients and calculate the pre-impact velocity components. This reverse calculation is important for vehicle accident reconstruction, since the pre-impact velocities are unknown and Post-impact Phase is the starting Point in a usual collision analysis. However. an inverse solution is not always Possible with the analytical rigid-body impact model. Mathematically, one does not exist under the common velocity condition. On the other hand, our method has a capability of reverse calculation under the condition if the absorbed energy during the collision process can be estimated using the crush profile. To validate the developed collision reconstruction a1gorithm, we use car-to-car collision test results. The analysis and experimental results agree well in the impact coefficients and the Pre-impact velocity components.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.85-93
• /
• 2003

Droplet vaporization at various ambient pressures is studied numerically by formulating one dimensional evaporation model in the mixture of hydrocarbon fuel and air. The ambient pressure ranged from atmospheric conditions to the supercritical conditions. The modified Soave-Redlich-Kwong state equation is used to account for the real gas effects in the high pressure condition. Non-ideal thermodynamic and transport properties at near critical and supercritical conditions are considered. Some computational results are compared with Sato's experimental data for the validation of calculations. The comparison between predictions and experiments showed quite a good agreement. The droplet lifetime increases with increasing pressure at temperature lower than the critical temperature, however, it decreases with increasing pressure at temperature higher than the critical temperature. The solubility of nitrogen can not be neglected in the high pressure and it becomes higher as the temperature and the pressure go up.

• International Journal of Highway Engineering
• /
• v.4 no.1 s.11
• /
• pp.149-159
• /
• 2002

This study was performed to estimate the high-speed direct tensile strength(DTS1), low-speed direct tensile strength(DTS2) , indirect tensile strength(ITS) resilient modulus(MR) and stiffness index(SI) of sand asphalt mixture based on the absolute viscosity, kinematic viscosity, penetration, softening point and PG grade of binder. DTS2 showed higher correlation with the physical properties than other properties of mixture, and the next was DTS1, ITS, SI and MR in order. Among binder properties, PG grade showed the highest relation with DTS2. Therefore. it was found that the high DTS mixture could be made when the binder with a high PG grade was used. However, since the individual physical property showed a relatively low correlation, various properties were used together in regression analysis. The estimation models of DTS and ITS were over 0.99, respectively. R2 of MR and SI estimation models were over 0.91 and 0.93, respectively. It was concluded that mechanical properties could be estimated with a high coefficient of determination from those physical properties.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.729-732
• /
• 2010

The present study has been motivated by the development of a reliable numerical methodology for simulation of kerosene/LOx coaxial swirl injectors. To deal with thermodynamic non-ideality and anomalies of transport properties pronounced at supercritical pressures, a set of subroutine libraries has been constructed based on the cubic equations of state, and applied to an existing flamelet analysis code. For computational efficiency, two-dimensional axisymmetric RANS formulation with swirl was adopted and validated successfully against an isothermal coaxial swirling jet. For the actual problem with high pressure combustion, however, numerical results show that the RANS models yield excessive production of turbulence probably due to high density gradient magnitude in the vicinity of mixing layer of swirling film flow, and imply strongly further improvement of the turbulence models.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.11
• /
• pp.889-897
• /
• 2014

This paper presents a method for finding an optimized result by using a genetic algorithm (GA) based on a PEMFC analysis result. The conventional analysis method designs fuel cells one-by-one, and each result is compared to obtain the best performance. Because the computational burden of the conventional analysis is enormous, the present optimization process provides an inefficient tool by automatically setting the boundary and material properties and mesh generation. As the change can be reflected automatically in the channel geometry with GA, the fuel cell analysis result with various sizes can be obtained easily. Therefore, the global maximum performance can be obtained through a GA optimization procedure.

• Fashion & Textile Research Journal
• /
• v.14 no.4
• /
• pp.648-659
• /
• 2012

This research categorizes fundamental data needed to develop eco-friendly fabrics treated with bamboo leaf & pine leaf extracts. The effect of mordant on those fabrics was analyzed through the measurement of mechanical properties and the estimation of primary hand values for cotton and silk fabrics dyed with bamboo leaf and pine leaf extracts that were later treated with various mordants. When cotton was dyed with bamboo leaves and pine leaves extracts, EM, WT, 2HB, 2HG, 2HG5, LC, T, and W increased however, RT, SMD, and RC decreased compared to raw cotton fabric. The B, G, and MIU increased after mordant treatment to the dyed cotton and resulted in a stiffer and rougher cotton's hand. EM, WT, RT, MIU, WC, T, and W increased (in terms of silk); however, LT, B, 2HB, G, 2HG, 2HG5, MMD, SMD, and LC decreased compared to raw silk fabric. Similar to the dyed cotton, mordant treatment increased the MIU and LC of dyed silk subsequently, the hand became stiffer and rougher. A greater tannin adsorption results in an increased mechanical property and the primary hand value. For both fabrics, mordant treatment made its smoothness drop. However, the scale of drop for cotton was significant, while the scale of the drop for silk was minor. In terms of type of mordant, femordant and natural-mordant treatment influenced the tensile, shear, surface properties of fabrics, and primary hand values more than Cu-mordant and synthetic-mordant in addition, this increased the stiffness, hardness, and roughness of fabrics.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.1
• /
• pp.57-70
• /
• 2009

Considerable advance has been made on research on effect of steel pipe Umbrella Arch Method (UAM) and mechanical reinforcement mechanism through numerical analyses and experiments. Due to long analysis time of three-dimensional analysis and its complexity, un-quantitative two-dimensional analysis is dominantly used in the design and application, where equivalent material properties of UAM reinforced area and ground are used, For this reason, development of reasonable, theoretical, quantitative and easy to use design and analysis method is required. In this study, both field UAM tests and laboratory tests were performed in the residual soil to highly weathered rock; field tests to observe the range of reinforcement, and laboratory tests to investigate the change of material properties between prior to and after UAM reinforcement. It has been observed that the increase in material property of neighboring ground is negligible, and that only stiffness of steel pipe and cement column formed inside the steel pipe and the gap between steel pipe and borehole contributes to ground reinforcement. Based on these results and concept of Convergence Confinement Method (CCM), two dimensional axisymmetric analyses have been performed to obtain the longitudinal displacement profile (LDP) corresponding to arching effect of tunnel face, UAM effect and effect of supports. In addition, modified load distribution method in two dimensional plane-strain analysis has been suggested, in which effect of UAM is transformed to internal pressure and modified load distribution ratios are suggested. Comparison between the modified method and conventional method shows that larger displacement occur in the conventional method than that in the modified method although it may be different depending on ground condition, depth and size of tunnel, types of steel pipe and initial stress state. Consequently, it can be concluded that the effect of UAM as a beam in a longitudinal direction is not considered properly in the conventional method.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.

• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1089-1096
• /
• 1997

본 연구에서는 에폭시/산무수물계에 화학양론비(r=산무수물/에폭시)를 0.5, 0.7,0.9,1.1로 변화시켜 서로 다른 두종류의 경화촉진제 1-cyanoethy1-2-ethy1-4-methy1 imidazole(2E4MZ-CN)과 N,N-dimethy1 benzy1 amine(BDMZ)을 첨가한 시료에 대한 경화거동과 경화 후 물성을 관찰하였다. 이 시료의 등온 경화거동은 동역학 측정기(dynamic mechanical analyzer, DMA)와 시차주사 열량분석기(differential scanning calorimeter, DSC)를 이용하여 조사하였다. DMA로부터 구해진 결과를 보면 경화시 상대저장강성을 (relative storage rigidity, RSR)과 상대손실강성율(relative loss rigidity, RSR)과 상대손실강성율(relative loss rigidity, RLR)의 변화가 r값과 경화촉진제의 종류에 영향을 받았다. 그리고 DSC결과는 r값이 감소함에 따라 경화가 촉진되는 것으로 나타났다. 경화물의 성질을 조사하기 위하여 사용된 DMA로부터 얻어진 유리전이온도(glass transition temperature, T$_{g}$)와 가교결합간의 평균분자량(average molecular weigh between crosslinks, M$_{c}$은 사용한 두 경화촉진제에 대하여 r값의 영향이 다르게 나타났다. BDMA의 경우는 T$_{g}$가 1:1화학양론비인 r=0.9에서 최고치를 보였으나, 2E4MZ-CN은 r이 감소함에 따라 계속 증가하는 양상을 보였다. 이와 같은 경향은 2E4MZ-CN을 경화촉진제로 사용하였을 때 에폭시가 과량으로 될수록 잔류 에폭시기들간의 에케르반응이 추가적으로 일어나 M$_{c}$가 감소하기 때문이다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.9
• /
• pp.875-883
• /
• 2010

The thermal performance of LNG fuel tanks of vehicles is determined by the time for non-venting storage of fuel and the amount of fuel supplied to the engine. In this study, we selected a double-walled vacuum-insulated fuel tank with a volume of 450 liter, and the properties of the fuel contained in it were assumed to be the same as those of the methane($CH_4$). For the increasing the non-venting fuel storage time, we propose the use of shielded penetration pipes in the tank. We compared the storage times of the tank used in our study with those of the conventional fuel tank. Further, the additional heat input required to maintain the fuel pressure necessary for an appropriate fuel supply rate was predicted. For these parameters, we derived a thermodynamic relationship that can be used to estimate the rate of increase in pressure for a known heat input, and we obtained equations for estimating the rate of heat leaked by using the established heat transfer model. From the results of numerical computation, we found the non-venting storage time of the tank with shielded pipes to be 25-30% higher than that of the tank with unshielded pipes. Further, we determined the appropriate operation conditions by taking into consideration the transfer rate of additional heat provided to the fuel tank.