• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.3
• /
• pp.198-210
• /
• 2006

POM(Princeton Ocean Model) was utilized in this study because it took ${\sigma}-coordinate$ system which could predict the behavior of bottom water. The model has been increasingly applied to costal area although it was initially developed as the ocean flow model. The original POM did not correct computational errors in transformation of ${\sigma}-coordinate$ system. The trying to reduce conversional errors might improve accuracy of flow velocity in vicinities of bottom layer. Therefore, in this study it was proposed to modify the original POM by using error correction method suggested by $Sl{\Phi}rdal$(1997). The modified POM was applied to Young-rang Lake, one of the typical brackish lakes in Korea. It was found that the behavior of bottom water could be well predicted. Thus, it seems that the modified POM can be used as a useful tool to clarify the mechanism of formation and behavior of bottom water including oxygen-deficient water mass.

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.2
• /
• pp.295-304
• /
• 1996

Toprovide economical BISDN service, with which integration process of many types of media is possible, it is necessary to construct a system with ground network and satellite network combined. The method for this type of transmission using satellite is TDMA that can provide services to many users in various area. However, the most difficult task to connect TDMA which uses synchronous method to ATM which used asynchronous transfer mode is the deterioration n of ATM transmission quality such as cell delay variation. Therefore, it is necessary to develop delay variation compensation method which can confront to the ATM. Efficient ways to use satellite links under the conditions such that maximum efficiency of the delay variation is limited under the required value, and the burst characteristic of transmission cell does not increase are being researched for translation between in ATM and TDMA. This paper points out the problems when time stamp method, reviewd in ground network, is applied to the satellite links to compensate the delay variation .To solve the problem, discrete cell count method is introduced along with the calculation of transmission capacity and error rate.Also, from the observation of stab-ility of the system and verification of reliability even when singal error occurred in the cell transmission timing information, the proposed compensation method appeared to be excellent.

• Korean Journal of Remote Sensing
• /
• v.33 no.2
• /
• pp.111-123
• /
• 2017

The phycocyanin pigment (PC) is a marker for cyanobacterial presence in eutrophic inland water. Accurate estimation of low PC concentration in turbid inland water is challenging due to the optical complexity and criticalforissuing an early warning of potentialrisks of cyanobacterial bloom to the public. To monitor cyanobacterial bloom in eutrophic inland waters, an approach is proposed to partition non-water absorption coefficient from measured reflectance and to retrieve absorption coefficient of PC with the aim of improving the accuracy in remotely estimated PC, in particular for low concentrations. The proposed inversion model retrieves absorption spectra of PC ($a_{pc}({\lambda})$) with $R^2{\geq}0.8$ for $a_{pc}(620)$. The algorithm achieved more accurate Chl-a and PC estimation with $0.71{\leq}R^2{\leq}0.85$, relative root mean square error (rRMSE) ${\leq}39.4%$ and mean relative error(RE) ${\leq}78.0%$ than the widely used semi-empirical algorithm for the same dataset. In particular, low PC ($PC{\leq}50mg/m^3$) and low PC: Chl-a ratio values of for all datasets used in this study were well predicted by the proposed algorithm.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.2
• /
• pp.1-13
• /
• 2018

This work discusses the major roles of digital technologies in the history of landscape architectural drawing, and offers a critique of the dominant trend towards realism in recent digital landscape representations. During the period of transition from conventional drawing tools, computer technologies generally functioned as mechanical tools to imitate prior manual techniques. Specifically, the GIS was served as a mechanical tool to efficiently process the manual layer cake; CAD software generally functioned to translate physical models to two-dimensional construction documents while graphic software generally functioned as a tool to perform processes similar to those of manual collage and montage techniques. Recent digital landscape drawings tend to adopt a realistic depiction like the painting of landscape appearance. In the representations, discernible traces of cutting and assembling are removed via graphic software; thus, the complete representations are perceived as if they were a copy of an actual landscape. The realistic images are an easy way to communicate with the public. However, it is difficult to achieve a full embodiment of all of the multisensory characteristics of a landscape through these visuals. They often deceive viewers by visualizing idealized conditions of not-yet-actualized landscapes and production of the final images takes up a large portion of the overall design process. Alternatively, 3D digital modeling of landscape performance and creative uses of digital technologies during the overall design process, as well as hybridized techniques with different drawing techniques and technologies, provide the opportunity to explore various aspects of a landscape.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.706-715
• /
• 2012

Electro-optical sigma-delta modulators are the core module of digital receiver to digitize wideband radio-frequency signals directly at an antenna. Electro-optical sigma-delta modulators use a pulsed laser to oversample an input radio-frequency signals at two Mach-Zehnder Interferometer(MZI) and shape the quantization noise using a fiber-lattice accumulator. Decimation filtering is applied to the quantizer output to construct the input signal with high resolution. The jitter affects greatly on reconstructing the original input signal of modulator. This paper analyzes the performance of first order single bit electro-optical sigma-delta modulator in the time domain and the frequency domain. The performance of modulator is analyzed by using asynchronous spectral averaging of the reconstructed signal's spectrum in the frequency domain. The reference value of time jitter is presented by analyzing the performance of jitter effects. This kind of jitter value can be used as a reference value on the design of modulators.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.80-87
• /
• 2013

A novel instrumentation amplifier(IA) using positive polarity current-conveyor(CCII+) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of two CCII+, three resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into two CCII+ used voltage and current follower converts into same currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the CCII+ and used commercial op-amp LF356. Simulation results show that voltage follower used CCII+ has offset voltage of 0.21mV at linear range of ${\pm}$4V. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the gain of 60dB was 400kHz. The IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 130mW at supply voltage of ${\pm}$5V.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.4
• /
• pp.40-48
• /
• 2012

This paper models the hue shift phenomenon and proposes a hue correction method to give perceptual matching between projector with and without additional white channel. To quantify the hue shift phenomenon for whole hue angle, 24 color patches with the same lightness are frist created along equally-spaced hue angle, and these are displayed one by one both displays with different luminance levels. Next, each hue value of the patches appeared on the projector with additional white channel is adjusted by observers until the hue values of patches on both displays appear the same visually. After obtaining the hue shift values from the color matching experiment, these values are piecewise fit into six polynomial functions, which approximately determine shifted hue amounts for an arbitrary hue values of each pixel in projector with additional white channel and are utilized to correct them. Actually, an input RGB image is converted to CIELAB LCH color space to get hue values of each pixel and this hue value is shifted as much as the amount calculated by the functions of hue shift model for correction. Finally, corrected image is inversely converted to an output RGB image. For an evaluation, the matching experiment with several test images and the z-score comparisons were performed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.1037-1044
• /
• 2010

In this paper, a new size-reduced, wideband ring-hybrid coupler is presented, and a design of a planar single-balanced doubler using the ring-hybrid is shown. This ring-hybrid coupler employs a pair of ultra-wideband transitions for phase inversion, which consists of in-phase and out of-phase transitions providing a good amplitude and phase balances for wide frequency ranges. The implemented ring-hybrid is 65 % smaller than conventional ring-hybrids, and provides 92.5 % and 81.3 % bandwidth at $\sum$ and $\Delta$ ports, respectively. Thanks to good amplitude and phase balances over wide bandwidth, the ring-hybrid can be applied to implement various balanced components. The implemented single-balanced doubler utilizing the ring-hybrid exhibits typical conversion loss of 10.5 dB for the output frequency range of 4~12 GHz with fundamental suppression level of 30 dB. The performance was also well-predicted with the nonlinear circuit simulation.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4_1
• /
• pp.129-136
• /
• 1992

A precedure for recovering surface displacement from a time series of pressure measured by a pressure gage in a shallow water (that is, FFTM, LCM. IWM) is investigated with respect to a proper cut-off-frequency of a frequency response function for the accurate recovery of wave height and period. The authors examined the applicability of above mentioned three transformation procedures through field observations and laboratory experiments and the following results are obtained. i) The cut-off-frequency of the frequency response function used in FFTM is deeply depend on both the frequency response of the pressure sensor and the water depth at the sensor. In this study, a relatively accurate surface displacement can be recovered when the frequency response function is cut off at the frequency corresponding to kh=3.0 where k is a wave number at the depth of h. The frequency response function in the region higher than the cut-off-frequency is set constant to be the value at the cut-off-frequency. ii) The transformed surface displacements by LCM are affected by the small waves of short periods included in the measured pressure. It is found that pressure variation whose local frequency is higher than kh=1.5 has to be neglected to recover surface displacement sufficiently. iii) In IWM, the linear pressure response function is usually utilized by multiplying a coefficient N which is a function of the frequency (or kh) and takes a value around unity. However, in this study, a constant value of N(=1.0) gives a relatively accurate recovery of surface displacements.

• Korean Journal of Cognitive Science
• /
• v.7 no.1
• /
• pp.57-74
• /
• 1996

This paper presents a comparison of recognition performance of the features used inthe recent handwritten korean character recognition.This research aims at providing the basis for feature selecion in order to improve not only the recognition rate but also the efficiency of recognition system.For the comparison of feature performace,we analyzed the characteristics of theose features and then,classified them into three rypes:global feature(image transformation)type,statistical feature type,and local/ topological feature type.For each type,we selected four or five features which seem more suitable to represent the characteristics of korean alphabet,and performed recongition experiments for the first consonant,horizontal vowel,and vertical vowel of a korean character, respectively.The classifier used in our experiments is a multi-layered perceptron with one hidden layer which is trained with backpropagation algorithm.The training and test data in the experiment are taken from 30sets of PE92. Experimental results show that 1)local/topological features outperform the other two type features in terms of recognition rates 2)mesh and projection features in statical feature type,walsh and DCT features in global feature type,and gradient and concavity features in local/topological feature type outperform the others in each type, respectively.