• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.96-103
• /
• 2005

The main purpose of launch vehicle is to insert satellite into a target orbit safely and correctly. To accomplish the main purpose of launch vehicle, the inserting velocity, inserting angle, and final mass of launch vehicle should be within the allowable range. In general, such requirements are satisfied with applying TCS(Thrust Control System) and TDS(Tank Depletion System), which manage thrust and mixture ratio by controlling propellant flow rate with thrust and mixture ratio control valves. In this study, the control characteristics of thrust and mixture ratio control valve were examined by PID control logic for stable operation of liquid-Propellant rocket engine at on-dosing point. The analysis on the control characteristics of control valves was done with AMESim code and the results from control valve test facility at KARI.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.69-69
• /
• 2003

우주발사체의 비행 목표는 위성의 궤도 투입이다. 이를 위해서는 발사체에서 요구되는 추력값과 총추력을 보장하는 추진기관이 개발되어야 한다. 엔진은 엔진 자체의 작동 안정성을 위해서 유량제어를 필요로 하지만, 이뿐만이 아니라, 발사체의 비행임무 수행을 위해서도 추진제가 모두 소진되는 시스템(TDS:Tank Depletion System) 개념이 도입되어야 하며, 이는 유량 제어를 통해서 실현된다. 본 연구에서는 우주발사체의 비행임무 수행에 필요한 즉, 총추력 오차 범위, 추력 오차 범위, 추진제 탑재량 및 잔류량 오차범위 관점에서 필요한 추진기관에 요구되는 성능을 검토하였고, 이를 위해 TDS 개념의 도입과 더불어 이를 구현할 수 있는 유량제어 개념을 제시하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.66-70
• /
• 2010

The performance of 75 ton liquid rocket engine combustion chamber for a space launch vehicle was predicted through firing tests at low pressure. In low pressure tests of 75 ton LRE combustor chamber, the combustion characteristic velocity of 1750 m/sec and the specific impulse of 240 sec were obtained which are higher than the low pressure performance of 30ton combustion chamber. The combustion characteristic velocity of 1770 m/sec and the specific impulse of 278 sec at design point for 75 ton LRE combustion chamber were predicted by using the low/high pressure performance correlation of 30ton LRE combustion chamber.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.8-13
• /
• 2010

An effective control of the axial thrust of a turbopump is one of the critical issues for obtaining its operational stability. Axial thrusts of the fuel pump for the 75-ton class rocket engine under development were measured with water as a test propellant at a room temperature. According to the test results, the axial thrust of the fuel pump seemed to satisfy the axial force condition of its bearing. Also, the thrust was increased as a whole when the flowrate of the pump was decreased. Furthermore it was found that the thrust and the leakage flowate were modified when the gaps between the floating ring seals and the impeller were changed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.1-12
• /
• 2019

A fundamental study on a gas injection variable thrust method for thrust throttling in a liquid rocket engine was conducted. The gas injection variable thrust has the advantage of not only being able to control the thrust with a simple structure but it also increases the atomization performance through the injection pressure drop that increases in direct proportion to the density reduction. In this study, spray characteristics such as spray instability, spray pattern, spray angle, and breakup length based on changes in the liquid mass flow rate and amount of injected gas were investigated using effervescent swirl injectors.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.68-76
• /
• 2004

It is essential to develop a transient engine system analysis model for turbopump fed type liquid rocket engine development, especially for deriving engine system test number and conditions. In this study, we proposed a mathematical model of turbopump fed type liquid rocket engine, and inspected transient mode changes around the nominal thrust level of a rocket engine according to variations of trust control valve's opening ratio. To verify the results, we solved the same problem with AnaSyn software from Russia, and concluded that the transient code showed the similar results within $2\%$ with AnaSyn.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.56-64
• /
• 2010

A system design has been conducted of the liquid rocket engine for Korean launch vehicle (KSLV-II, Korea Space Launch Vehicle II). The present turbopump-fed liquid rocket engine of vacuum thrust 76 ton and vacuum specific impulse 297 sec adopts gas generator cycle. The combustion pressure of the regeneratively cooled combustor is 60 bar. The propellant is LOx/kerosene. The engine is started by pyrostarter and the combustor is ignited by TEA (TriEthylAluminium). The engine system performance and the subsystems performance requirements are given through energy balance analysis. The combustion pressure, specific impulse and the engine mass are analyzed to be reasonable comparing with the published data. The startup analysis method which will be used in the future has been validated against the turbopump-gas generator coupled test. The tuning method for performance variation of the engine which is not actively controled has been prepared by mode analysis and performance deviation analysis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.585-589
• /
• 2010

It is important for the liquid rocket engine to meet the exact performance requirements in order to guarantee the successful mission of the launch vehicle. Usually, a ground combustion test for the engine is conducted to reduce the performance error and for the tuning. For the gas-generator (GG) cycle engine, this adjustment process can be easily tuned by means of the control valves. A linearized correlation between the process parameters of the control - the combustion chamber pressure and the mixture ratio of engine - and the independent parameter of the control- rotational angle of the control valve - could be suitable to reduce the tuning errors. Also this linearity can reduce the effort for the tuning and make the process more explicit by ensuring a more intuitive control. In this point, we proposed an algorithm in the frame of the in-house-developed program to obtain the control valves' inherent characteristics which satisfy the linearity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.27 no.1
• /
• pp.58-67
• /
• 2023

Results of dry-run tests, cold-flow tests, and hot-firing tests performed to throttle a methane engine uni-element thrust chamber are covered in the paper. After installing flow control valves on the oxidizer and fuel supply lines of the methane engine combustion test facility, a number of dry-run tests were repeated so that the valves could reach set strokes quickly and stably. Then, cold-flow tests using liquid nitrogen and gaseous nitrogen were conducted to confirm the stable supply of the simulated propellants according to the valve control. Finally, using liquid oxygen and gaseous methane, hot-firing tests for fixed and continuous thrust control of 50% to 10% of the nominal thrust were successfully performed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.123-127
• /
• 2005

LRE(liquid rocket engine) performance design code with several modules for each engine component has been developed for a preliminary design purpose. Thrust chamber, non-cryogenic centrifugal pump, single stage axial impulse turbine, gas generator and exhaust pipe for extra thrust have been considered. For simplicity, pump exit pressures are fixed, which eliminates pressure balancing problem between thrust chamber and turbopump unit. In this paper, calculated performance parameters with system flow charts and the design methodologies for each component are briefly presented and the results are compared with tile real engine specification.