• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.76-83
• /
• 2017

Korea Aerospace Research Institute(KARI) has been developing a new launch vehicle Korea Space Launch Vehicle-II(KSLV-II) with their own technology. Thus, it is required a new launch complex that corresponds to a new propulsion system of launch vehicle. Because widely changing of KSLV-II comparing with KSLV-I such as thrust of engine system, composition of vehicle staging, pneumo-hydraulic scheme of propulsion system, it is important to establishing appropriate ground support equipments for fuel(kerosene) filling. In this critical design process, specific supply line and specification of components are designed and the concept of kerosene filling is determined based on results of preliminary design. Also, plans of supply operation and prerequisite are established and operation algorithms are formed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.26-29
• /
• 2017

KARI has been conducting R&D for independent development of KSLV-II since 2010. Vehicle holding device is a device for vertically standing SLV on the launch pad of launch complex and fixing the lower part of vehicle in order to firmly fix vehicle so that SLV does not fall from an external load such as a wind load. When thrust generated after the 1st stage engine ignition of SLV must exceed the takeoff weight of vehicle, and holding device should be quickly released so that it does not interfere with takeoff of vehicle like other ground equipment at the beginning of the launch. Pyro-valve is one of the key components constituting VHD, and it should have high reliability and quick response characteristics with similar functional parts applied to launch vehicle separation device and satellite separation device. Through this paper, I intend to broaden the overall understanding of the development process of pyro-valve for VHD and KSLV-II.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.91-96
• /
• 2004

An optimal design of the gas generator for Liquid Rocket Engine (LRE) was conducted. A fuel-rich gas generator in open cycle turbopump system was designed for 10ton in thrust with RP-1/LOx propellant. The optimal design was done for maximizing specific impulse of thrust chamber with constraints of combustion temperature and for matching the power requirement of turbopump system. Design variables are total mass flow rate to gas generator, O/F ratio in gas generator, turbine injection angle, partial admission ratio, and turbine rotational speed. Results of optimal design provide length, diameter, and contraction ratio of gas generator. And the operational condition predicted by design code with resulting configuration was found to maximize the objective function and to meet the design constraints. The results of optimal design will be tested and verified with combustion experiments.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.44-50
• /
• 2017

Vehicle Holding Device(VHD) has a role that holding the launch vehicle on its launch pad until the engine therust reaches a steady condition. The analytical study of shape parameters and dynamic characteristics of hydraulic cylinders is carried out. The contraction of cylinder is considered as the major factor of releasing mechanism. Through the analysis, the decreasing of cylinder slit size and increasing initial charging pressure increase the contraction force. Through the transient analysis, cylinder load, displacement and inner pressure distribution are confirmed. The cylinder contraction force is converged to the cylinder external force when the cylinder starts to move. Also, the pressure distribution in the hydraulic cylinder is constant.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.5
• /
• pp.383-388
• /
• 2021

Air-breathing engines used in aircraft have a performance limit as the altitude increases, and this determines the service and absolute ceiling altitude. The method of maintaining altitude and speed in a fixed-wing aircraft in level flight using classical control method is generally using thrust for speed increase/deceleration and pitch attitude for altitude increase/decrease. If this method is used near the service ceiling altitude, increasing the pitch to reduce the altitude error results in a speed reduction. Therefore, it is necessary to use a control method that maintains the speed first using the pitch attitude. Especially in the case of unmanned aerial vehicles, these two methods should be automatically available at the right time. In this paper, we propose a method of switching the speed and altitude maintenance algorithm near service ceiling altitude.

• Journal of Aerospace System Engineering
• /
• v.16 no.5
• /
• pp.78-85
• /
• 2022

Multicopter-type unmanned aerial vehicles (UAV) are increasingly for cargo transportation to mountainous and island regions, image information acquisition in disaster areas, and emergency rescue transport. In order to successfully perform these tasks, the aircraft structure must be able to safely support the loads induced by flight conditions while ensuring the vibration and aeroelastic stability of the prop-rotor. This study introduced a structural analysis model of a 40kg payload multicopter with an engine-generator hybrid power system. The deformation and stress distribution are investigated depending on the load conditions. In addition, the vibration characteristics and aeroelastic stability of the prop-rotor were also presented to flight speed and aircraft pitch angle. The maximum thrust generated by the prop-rotor and the landing load applied to the multicopter under normal and emergency landing conditions were reviewed., It confirmed that the structure could support without failure. In addition, it confirmed that the damping characteristics of each primary locate in the constant region according to the aircraft's flight speed and the prop-rotors rotating speed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.12
• /
• pp.1087-1094
• /
• 2016

The responsibility of the vehicle holding device (VHD) is to hold the launch vehicle while it is stayed on launch pad and release the holding mechanism to allow a lift-off of launch vehicle at a moment of lift-off. During a release of the holding mechanism, in order to prevent the Ka doing a doing a doing mode which is vertical oscillation of entire liquid propellant and very severe for vehicle structure, gradual release of holding force is required. Also, a release operation of all 4 VHD should be synchronized very precisely. In this study, to comply the "gradual release and synchronized operation requirement", concept of VHD hydraulic system using an accumulator, pyro valve and orifice to control speed of hydraulic cylinder is proposed instead of using complicated hydraulic components. Then through multi-body dynamic analysis and computational hydraulic analysis, a size of orifice to meet a target speed of hydraulic cylinder is calculated. Through this study, simple and reliable VHD hydraulic system complying requirements is designed.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.2
• /
• pp.43-54
• /
• 2018

Underwater tracked vehicle is employed to perform underwater heavy works on saturated seafloor. When an underwater tracked vehicle travels on the seafloor, shearing action and ground settlement take place on the soil-track interface, which develops the soil thrust and soil resistance, respectively, and they restrict the tractive performance of an underwater tracked vehicle. Thus, unlike the paved road, underwater tracked vehicle performance does not solely rely on its engine thrust, but also on the soil-track interaction. This paper aimed at evaluating the tractive performance of an underwater tracked vehicle with respect to ground conditions (soil type, and relative density or consistency) and vehicle conditions (weight of vehicle, and geometry of track system), based on the soil-track interaction theory. The results showed that sandy ground and silty sandy ground generally provide sufficient tractions for an underwater tracked vehicle whereas tractive performance is very much restricted on clayey ground, especially for a heavy-weighted underwater tracked vehicle. Thus, it is concluded that an underwater tracked vehicle needs additional equipment to enhance the tractive performance on the clayey ground.