• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.04a
• /
• pp.383-384
• /
• 2010

The control surface on a ship is to control the motion of it in forward and backward states. In this paper, the measured results has been compared with each other to predict the backward flow characteristics of the single rudder's 2-dimensional section at $Re=2.0\times10^4$ using 2-frame grey level cross correlation PIV method especially, The separation region appears at 10 to 20 degrees angle of attack in a forward state. The separation point and boundary layer demonstrate in the same angle of attack compared it with the forward states.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.43 no.6 s.312
• /
• pp.110-116
• /
• 2006

In this paper, we implement a speech recognition system to support ubiquitous sensor network application services such as switch control, authentication, etc. using wireless audio sensors. The proposed system is consist of the wireless audio sensor, the speech recognition algorithm using psychoacoustic model and LDPC(low density parity check) for correcting errors. The proposed speech recognition system is inserted in a HOST PC to use the sensor energy effectively mil to improve the accuracy of speech recognition, a FEC(Forward Error Correction) system is used. Also, we optimized the simulation coefficient and test environment to effectively remove the wireless channel noises and correcting wireless channel errors. As a result, when the distance between sensor and the source of voice is less then 1.0m FAR and FRR are 0.126% and 7.5% respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.1
• /
• pp.38-43
• /
• 2018

Ceramic membrane has been widely used for water treatment due to its advantages of eco-friendly property and low energy consumption. However, high porosity of ceramic membrane higher than 40 % may cause a problem of strength, when it is applied to a water treatment module. In order to solve this problem, the strength of the membrane edge was improved by using the ceramic glaze. Four different glaze compositions for low temperature sintering was selected to minimize the deformation of the membrane microstructure. After coating with low temperature glaze, cracks were observed due to differences in thermal expansion coefficient between the membrane and glaze. Thus, the thermal expansion coefficient of glaze was controlled by addition of cordierite and petalite. As a results, the compressive strength of the ceramic membrane, which was coated with the optimized glaze composition, was increased from $27N/m^2$ to $117N/m^2$, indicating that the glaze coating can improve the disadvantages of the fragile ceramic membrane.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.718-725
• /
• 2002

A wall type friction damper is newly Proposed in this paper to improve the performance of R/C framed structures under earthquake loads. Although traditional dampers are usually placed as bracing members, the application ot bracing-type dampers into R/C structures is not as simple as those of steel structures due to the connection between R/C members and dampers and the stress concentration in connection region. Proposed damper is consisted of Teflon-sheet slider and R/C shear wall. The damper can also avoid stress concentration and reduce P-Δ effect. To evaluate the performance of proposed damper, nonlinear dynamic analyses are carried on 10 story and 3 bay R/C structures with numerical model for the damper. It is shown that the damper reduces the inter-story drifts and the time-historic responses; especially the damper prevents from forming plastic hinges on the lower columns.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.4
• /
• pp.403-411
• /
• 2014

In this paper, an algorithm of extracting the features of home appliances and automatically building a database to identify home appliances is designed and presented. For the verification, a software library supporting this algorithm is implemented and added to an power management system server, which was already implemented to support real-time monitoring of home appliances' power consumption status and controlling their power. The implemented system consists of a system server and clients, each of which measures the power consumed by a home appliance plugged in it and transmits the information to the server in real-time over a wireless network. Through experiments, it is verified that it is possible to identify any home appliance connected to a specific client.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2003.09a
• /
• pp.81-81
• /
• 2003

목적 : 현재, 많은 병원이 방사선과 의료영상정보를 기존의 필름형태로 판독하고, 진료하는 방식에서 PACS 를 도입하여 디지털 형태로 영상을 전송, 저장, 검색, 판독하는 환경으로 변화하고 있다. 한편, PACS 가 가지는 가장 큰 제한점은 휴대성의 결핍이다. 본 연구는 이동형 장치가 가지는 호스트의 이동성 및 휴대성의 장점들을 살리면서, 무선 채널 용량의 한계, 무선 링크 사용이라는 제약점들을 감안하여 의료영상을 JPEG2000 영상압축 방식으로 부호화한 후 무선 환경을 고려한 전송 패킷의 크기를 결정하고자 하였으며, 무선 통신 중 발생되는 패킷 손실에 대응하기 위한 자동 오류 수정 기능도 함께 구현하고자하였다. 방법 : Window 2000 운영체계에서 의료영상을 로드하고, 데이터베이스화하며, 저장하고, 다른 네트워크와 접속, 제어가 가능한 PC급 서버를 구축하였다. 영상데이터는 무선망을 통해 전송하기 때문에 가장 높은 압축비율을 지원하면서 에너지 밀도가 높은 JPEG2000 알고리즘을 사용하여 영상을 압축하였다. 또한, 무선망 사용으로 인한 패킷 손실에 대비하여, 영상을 JPEG2000 방식으로 부호화한 후 각 블록단위로 전송하였다. 결과 : PDA에서 JPEG2000 영상을 복호화 하는데 걸리는 시간은 256$\times$256 크기의 MR 뇌영상의 경우 바로 확인할 수 있었지만, 800$\times$790 크기의 CR 흉부 영상의 경우 약 5 초 정도의 시간이 걸렸다. CDMA 1X(Code Division Multiple Access 1st Generation) 모듈을 사용하여 영상을 전송하는 경우, 256 byte/see 정도에서는 안정된 전송 결과를 보여주었고, 1 Kbyte/see 정도의 전송의 경우 중간 중간에 패킷이 손실되는 결과를 관찰할 수 있었다. 반면 무선 랜의 경우 이보다 더 큰 패킷을 전송하더라도 문제점은 발견되지 않았다. 결론 : 현재의 PACS는 유선과 무선사이의 인터페이스의 부재로 인해 유무선 연동이 되지 못하고 있다. 따라서 이동형 JPEG2000 영상 뷰어는 PACS가 가지는 문제점인 휴대성을 보완하기 위하여 개발되었다. 또한 무선망이 가지는 데이터 손실에 대하여서도 허용할 수 있는 범위에서 재전송을 가능하게 함으로서 약한 연결성을 보완하였다. 본 JPEG2000 영상 뷰어 시스템은 기존 유선상의 PACS와 이동형 장치간에 유기적인 인터페이스 역할을 하리라 기대된다.

• Explosives and Blasting
• /
• v.34 no.1
• /
• pp.11-18
• /
• 2016

It is necessary to minimize ground vibration and noise due to blasting work in urban environment. The blast induced ground vibration and noise are generally generated by a portion of detonation energy, where most of the energy is utilized for rock breakage and movement of rock mass. Recently a blast method utilizing U-shaped steel charge holder was suggested to reduce the ground vibration without decreasing destructive power toward the free surface. In this study, single hole blasting utilizing U-shaped steel charge holder were simulated and the stress waves caused by the detonation of explosives were monitored using AUTODYN software. In order to examine the fragmentation efficiency of the U-shaped steel charge holder, one free face blasting models which adapt the blast induced stress waves were simulated by dynamic fracture process analysis (DFPA) code. In addition, the general blasting models were also simulated to investigate the fragmentation effectiveness of the U-shaped steel charge holder in rock blasting.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2001.05a
• /
• pp.141-146
• /
• 2001

실내 공기조화를 하는 거주역에 대한 온열환경요소의 자극 변화를 통해 실내 에너지를 절약할 수도 있으며 쾌적감도 향상시킬 수 있다. 따라서 본 연구에서는 거주자의 온열감각을 자극할 수 있는 온열요소 중 비교적 영향이 크고 용이하게 제어할 수 있는 온도 및 기류의 변동으로 한국인의 온열감각(온냉감, 쾌적감, 만족감)에 미치는 영향을 실험을 통하여 파악하였다. 온도 및 기류별 실험을 통하여 22$^{\circ}C$, 24$^{\circ}C$, 26$^{\circ}C$의 각 온도에 대한 패케지 에어컨의 강, 중, 약 기류에 대한 인체순응 시간과 인체 변화를 파악하였다. 또한 인체순응시간을 고려한 온도 상승 실험을 통하여 24$^{\circ}C$, 26$^{\circ}C$에서 1$^{\circ}C$온도 상승시 인체의 온열쾌적감의 변화를 파악하였으며 온도 상승을 통한 인체 순응시간을 도출하였다. 본 실험을 통하여 초기공조 조건을 24C$^{\circ}C$ 로 한 경우 인체순응을 통한 온도 상승으로 30분 후의 공조중기와 공조후기에 온도 및 기류의 지속적인 변동 자극으로 온냉감은 "약간 서늘하다"를 지속적으로 유지하고 있으며 온도상승으로 인한 쾌적존의 높은 온도에서도 기류의 영향으로 쾌적감은 30분 이후부터 "쾌적"을 지속적으로 유지하는 것을 알 수 있었다. 따라서 본 연구를 통하여 인체순응을 고려한 온도 및 기류의 자극을 통하여 공조초기부터 공조말기의 장시간에도 인체가 지속적인 쾌적성을 유지한다는 것을 알 수 있었다.성을 유지한다는 것을 알 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.28-37
• /
• 2002

Acoustic behavior in combustion chamber with acoustoc cavity is numerically investigated by adopting linear acoustic analysis. Helmholtz-type resonator is employed as a cavity model to suppress acoustic instability passively. The tuning frequency of acoustic cavity is adjusted by varying the sound speed in acoustic cavity. Through harmonic analysis, acoustic pressure responses of chamber to acoustic oscillating excitation are shown and the resonant acoustic modes are identified. Acoustic damping effect of acoustic cavity is quantified by damping factor. As the tuning frequency approaches the target frequency of the resonant mode to be suppressed, mode split from the original resonant mode to lower and upper modes appears and thereby damping effect is degraded significantly. Considering mode split and damping effect as a function of tuning frequency, it is desirable to make acoustic cavity tuned to maximum frequency of those of the possible splitted upper modes.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.4
• /
• pp.53-59
• /
• 2003

Strain Energy Hinge(SEH) has been used in Korea Multi-purpose Satellite(KOMPSAT) series to deploy the solar panel due to the good record of reliability. However, when it reached a desired deployment position, a large buckling force is applied to the main body. This may cause structural damage and also affect control of the satellite. Therefore, reliable dynamic analysis for the deployment system is required at a design stage. Moreover, various mission of a satellite has made the size of solar panels got bigger, so elastic effect has to be considered seriously to get more precise analysis results. In this paper, a dynamic analysis method to predict the deployment is verified by KOMPSAT-2 deployment test.