• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.221-223
• /
• 2008

In Korean urban transit system, when the railcar starts, the electric power is absorbed from the line, and then the line voltage is instantaneously collapsed to provide a large accelerating torque. On the other hand, when the railcar brakes, the regenerative power is created and it increases the line voltage at the pantograph of the railcar. Therefor, by using the energy storage system near the train, the regenerated power can be saved to this system. The energy storage system is consisted of supercapacitor and a bidirectional DC-DC converter. In this paper, controller design of a bidirectional DC-DC converter based on pole-assignment is proposed. This method can be easy to design controller. Simulation results by using the calculated parameters are presented.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.85-86
• /
• 2015

In this paper, the bidirectional DC-DC converter is composed of the 900V Silicon-Carbide(SiC) devices to get high efficiency. The 900V SiC device is better than a similar current rated traditional SiC device. it has a lower drain-source resistance and output capacitance. therefore it can reduce the switching and the conduction losses of the DC-DC converter. The experimental results verify the improvement of efficiency and usefulness of 900V SiC device.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.198-199
• /
• 2010

In this paper, bi-directional DC/DC converter using a LC series resonant converter is proposed. A proposed converter is consisted by adding LC series resonant tank into a conventional bi-directional DC/DC converter and performs soft-switching at both boost and buck mode. A LC series resonance occurs in whole operation mode and switching point is determined by specific condition. Through the theoretical analysis and simulation results, operation modes and characteristics of the proposed topology is verified.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.41-42
• /
• 2012

For achieving the high gain and resonant characteristics in both of the power flow directions, a bidirectional resonant dc-dc converter with auxiliary switches is proposed. Auxiliary switches are connected in the primary and secondary side of the bidirectional resonant dc-dc converter, respectively. A 1kW prototype bidirectional resonant dc-dc converter for interfacing the 400V DC buses in the energy storage system is built and tested to verify the validity and applicability of this proposed converter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.61-68
• /
• 2004

Recently, a fuel cell is remarkable for new generation system. The fuel cell is characterized by low voltage and high current. Therefor, for connecting to general load, it needs both a step up converter and an inverter. The proposed system consists of an isolated DC-DC converter to boost the fuel cell voltage to 380[Vdc] and a PWM inverter with LC filter to convert the dc voltage to single phase 220[Vac]. Also, bi-directional DC-DC converter for fuel cell generation system is composed to improve load response characteristic. In this paper, full bridge converter and the single phase inverter are designed and installed for fuel cell. Simulation and experiment verify that fuel cell generation system could be applied for the distributed generation.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.13-14
• /
• 2014

본 논문에서는 유사 DC-Link 타입의 태양광 마이크로 인버터에서 요구되는 대용량의 전해 커패시터의 단점을 지적하고 이를 제거하기 위해 shunt 방식으로 연결되는 양방향 벅-부스트 컨버터 제어방법을 제안한다. 태양광 마이크로 인버터는 동작 특성상 PV 입력단에 120Hz 리플이 존재하지만 대용량의 전해 커패시터를 적용함으로써 리플을 제거할 수 있다. 하지만 전해 커패시터의 짧은 수명이 전체 시스템의 신뢰성을 저하시키기 때문에 이를 극복하기 위한 부가적인 회로가 필요하다. 본 논문에서는 제안한 1차측의 플라이백 스위치 전류 제어기의 레퍼런스를 공유함으로써 전류 센서수를 감소시키고 PV 입력단 Capacitance를 낮출 수 있는 양방향 벅-부스트 회로의 제어기를 시뮬레이션을 통하여 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.157-158
• /
• 2011

This paper deals with the minimization of switching loss of a dual full-bridge bidirectional DC-DC converter for supercapacitor. In case of charging mode the switching loss can be minimized with proper switching pattern, and the switching loss in discharging mode can be minimized with soft switching. Simulation results show that the switching loss is reduced considerably.

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.21-23
• /
• 2007

In this paper a high efficiency bi-directional DC-DC converter for hybrid vehicles is proposed. The proposed converter a three-phase half-bridge interleaved ZVS converter, is designed to have high efficiency in the main operation range. The component ratings are calculated, the actual devices are selected, and the efficiency analysis has been performed to determine optimal ZVS range. The input and output current ripples are significantly reduced due to the interleaved operation. The dual loop control for the interleaved three-phase converter is also presented. To confirm the proposed convert ter, The simulation and experimental results are presented.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.13-14
• /
• 2011

This paper deals with the ZVS characteristics of a bidirectional DC/DC converter in idling mode. Simulations are carried out with the supercapacitor which maximum voltage is 50 V. It is found that the ZVS can be achieved as far as the supercapacitor voltage is below 94% of the maximum voltage in idling mode. Therefore, the switching loss in the mode can be small by control the upper limit of the supercapacitor voltage.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.479-483
• /
• 2004

Fuel Cell (FC) has slow response characteristic for load variation. During a load step, the inverter cannot pull more power from the fuel cell than is currently available so supplemental power must be provide by some sort of energy storage elements. In this paper, hi-directional do-dc converter for FC generation system is proposed to improve load response characteristic. The hi-directional converter interfaces the low voltage battery to the inverter dc link of FC generation system. The converter is based on a active full bridge in the primary side and on a half bridge in the secondary of a high frequency isolation transformer. The complete operating principles and simulation results in presented.