• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1057-1059
• /
• 2017

In development of liquid-propellant rocket engine, engine gimbaling requires various types of bellows movements and cryogenic insulation is applied with movement-based design and material on each axial and circular bellows. Cryogenic insulation of Bellows for high pressure line and recirculation line are necessary to maintain cryogenic temperature for engien efficiency and protect from heat transfer and radiation of high temperature components during engine gimbaling.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.165-169
• /
• 2007

Qualification test range for Lox/Kerosene gas generator cyle liquid rocket engine was determined by considering engine dispersion and flight inlet conditions. With various pump characteristics, the operation range of components and system was investigated through dispersion analysis. The variation of engine performance shows opposite trends in calibration and dispersion.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.182-194
• /
• 2012

To develop a liquid rocket engine with high reliability and safety under constraints of limited time and budget an optimal diagnosis system for the engine needs to be developed in parallel with the development of the engine. This paper is intended to set a development direction of the diagnosis system for the liquid rocket engine through the literature survey and addresses possible engine defects, characteristics of parameters for diagnosis and diagnostic methods including real-time diagnosis, post-test/post-flight diagnosis, fault detection method, parameter circuit method and test diagnosis. In addition tasks to be performed in the design and operation phases of the engine and foreign application case of engine diagnosis are presented.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.120-125
• /
• 2020

75 tonf liquid rocket engine combustion test was performed at Naro space center Engine Combustion Test Facility for KSLV-II. A gradual pressure drop was observed during off-design combustion test turbopump inlet condition using cooled kerosene at 271 K. It was found that the water content inside kerosene could cause pressure drop at 40 ㎛ grade filter through the water contests analysis of kerosene, kerosene cooling test and dehydration of kerosene.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.126-133
• /
• 2018

A liquid rocket engine experiences various static loads in flight, such as high pressures due to propellents, thrust and thermal loads due to cryogenic liquid oxygen and combustion gas with extreme vibration. During the engine development stage, structural analyses and investigation on the strain measured from ground firing tests are necessary for determining the structural reliability of the engine. In this study, the strain characteristics, obtained from the ground firing tests of a 75 tonf-class engine, were analyzed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1054-1056
• /
• 2017

The Preparation for a flight test of the launch vehicle to verify the performance of the liquid rocket engine(LRE) is proceeding. Flight test of liquid rocket engine costs an enormous amount of money, has a restriction on measurement channels, so it requires the optimal measurement plan to check the prelaunch operation and determine the cause of abnormal situation. This paper surveys the foreign sources for LRE flight test. In recent years, as the tendency to eliminate all faults of LRE at the ground test the number of flight test is decreasing and in contrast, the number of measurements and measurement accuracy is increasing. This paper may be used as a reference for the preparation of an LRE flight test.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.93-97
• /
• 2010

The energy balance program which can balance the relations among energy, mass flow, pressure in the staged-combustion cycle of the liquid rocket engine has been developed. The modular approach has been chosen for the analysis; the engine cycle consists of the elements from the predefined component analysis program. The engine with the staged-combustion cycle has been decomposed into several principal component modules, such as a thruster chamber, turbopumps, turbines, supply system components and a pre-burner. The program has been verified with comparison of the results to the selected data of the space shuttle main engine.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.200-206
• /
• 2013

A performance sensitivity of liquid rocket engine to propellant density or supply pressure change was studied. The analysis program was verified to have 1% error comparing with the measured data of a turbopump-gas generator system. The engine combustion pressure decreases as fuel supply pressure increases due to decreased mixture ratio which reduces the turbine power. The engine combustion pressure increases as fuel density increases because the total propellant flow rate is increased substantially even though mixture ratio is slightly decreased. The engine combustion pressure increases when the oxidizer density or supply pressure increases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.181-184
• /
• 2006

We successfully completed the development test for a 10-ton thrust liquid rocket engine using LOX+LNG (Liquefied Natural Gas, or Methane) with a high performance turbopump system. Resulting from the success of the regenerative-cooling capability using LNG, high pressure-generating capability and gas-generating performance, etc, methane engine with the product name CHASE-10 will be commercialized in the near future.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.162-165
• /
• 2004

A layout of regenerative liquid rocket engine using turbo pump has been designed for development of high performance liquid rocket engine. each components of engine system was placed by considering assembly and characteristic. first stage engine system is controled by one plane of axis gimballing and composed of four engine assembly to cluster with launch vehicle. second stage engine system is controled by two plane of axis gimballing and composed of one engine assembly. assembly and disassembly processes and required program have been developed. various shape of instruments were also developed for carrying out assembly and disassembly process efficiently