• Applied Chemistry for Engineering
• /
• v.9 no.6
• /
• pp.894-900
• /
• 1998

An interphase between carbon fiber and epoxy matrix was introduced to increase impact strength of carbon fiber reinforced composites (CFRC) without sacrificing the interlaminar shear strength. Flexible polymers, I. e., MVEMA (poly(methyl vinyl ether-co-maleic anhydride)) and EMA(poly(ethylene-co-maleic anhydride)), which have reactive functional groups were considered as interphase materials. Weight hain of MVEMA and EMA onto the surface of carbon fibers was evaluated by changing the parameters of electrodeposition process. Electrodeposition mechanism of polymers which have anhydride functional group was identified by IR spectroscopy, that is, the generation of $RCOO^-$ functional group by the attack of hydroxide anion in the basic solution was observed. The weight gain was increased by increasing concentration of polymers, current density, and electrodeposition time. However the excess generation of oxygen gas decreased the weight gain by removing the deposited polymers. Washing in the running water easily removed the deposited polymers which are on the fiber surface without bonding, as a results, only 0.5 wt% of deposited polymers are remained.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.8
• /
• pp.603-610
• /
• 2009

This research was performed to improve removal efficiency of toluene and methyl ethyl ketone (MEK) using Candida tropicalis, one of the yeast species. An airlift loop bioreactor (ALB) was employed to enhance the capability of mass transfer for toluene and MEK from the gas phase to the liquid, microbial phase. Polymer gel media made from PAC, alginate and PEG was applied for the effective immobilization of the yeast strain on the polymer gel media. The experimental results indicated that the mass transfer coefficient of toluene without polymer gel media was 1.29 $min^{-1}$ at a gas retention time of 15 sec, whereas the KLa value for toluene was increased to 4.07 $min^{-1}$ by adding the media, confirming the enhanced mass transfer of volatile organic compounds between the gas and liquid phases. The removal efficiency of toluene and MEK by using yeast-immobilized polymer gel media in the ALB was greater than 80% at different pollutant loading rates (5, 10, 19 and 37 g/$m^3$/hr for toluene, 4.5, 8.9, 17.8 and 35.1 g/$m^3$/hr for MEK). In addition, an elimination capacity test conducted by changing inlet loading rates stepwise demonstrated that maximum elimination capacities for toluene and MEK were 70.4 and 56.4 g/$m^3$/hr, respectively.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.11a
• /
• pp.41-41
• /
• 2000

부유부상 공정은 현재 신문고지와 사무용 고지의 탈묵을 통한 신문용지 및 화장지 제조 에 널리 사용되고 있는 고지재활용을 위한 핵심공정이다. 하지만 이들 공정은 갈수록 열악 해지는 국내 고지원료의 품질변화에 따라서 잉크 및 토너의 분리효율이 저하되고 있어 생산 되는 탈묵 펄프의 품질저하, 리젝트 발생량의 증대, 폐수 처리공정의 부하 증가 등 다양한 문제점을 발생시키고 있어 이에 대한 대책의 수립이 시급히 요청되고 있다. 현재와 같이 다양한 형태의 잉크 및 인쇄방식으로 인쇄된 많은 종류의 재활용지가 원료 로 투입되고 있는 경우 탈묵공정의 효율 향상을 위해서는 부유부상 공정에 대한 좀 더 체계 적이고 논리적인 접근이 필요하다. 이러한 문제점을 극복하기 위해 먼저 고지 재활용 공정 의 핵심 단위공정인 부유부상 공정에 관련된 복잡한 문제점을 단순화하여 고상 및 액상의 표면화학적 특성을 평가하고, 이에 따른 부유부상 공정의 효율을 분석하였다. 본 연구에서는 부유부상 공정을 기초과학적 측면에서 구명하기 위해 마이크로 크리스탈린 셀룰로오스(Microcrystalline cellulose: MCC)를 모델 물질로 사용하였고, 친수성 의 표면 특 성을 나타내는 MCC의 표면 특성을 바꾸기 위하여 AKD(alkyl ketene dimer)로 처리비율을 달리하여 사이징 처리하였다. 부유부상 실험에 사용된 MCC는 친수성을 띠는 것과 소수성 을 부여한 것을 구별하고 그 비율을 백색도를 통해 측정하기 위하여 자체적으로 친수성을 가지는 MCC는 세척 견뢰도가 높은 검은색 염료로 염색하였다. 준비된 친수성과 소수성 M MCC의 혼합비율 별로 패드를 작성하여 백색도를 측정함으로써 검량선을 작성하였다. 또한 부유부상 시간에 따른 제거효율을 알아보기 위하여 부유부상 시간별로 각각의 리젝트율과 수율올 측정하고, 리젝트 시료로부터 패드를 제조하여 백색도를 측정하였다. 실험 결과 소수성 MCC의 소수화 정도에 따라서 리젝트율이 증가하였으며, 이를 통해 표 면에 소수성을 띠는 입자는 소수성이 강할수록 부유부상공정에서 제거율이 증가한다는 것을 확인하였다. 부유부상 처리한 MCC로 패드를 제조한 뒤 백색도를 비교한 결과에서도 이를 확인하였다. 한편 리젝트로 함께 제거된 MCC 내에 존재하는 친수성 MCC의 양은 극히 미 세하였다. 또한 부유부상를 실시하는 초기에 상당량의 리젝트가 발생함을 확인하였는데, 이 는 전체 부유부상을 통해 제거되는 양의 45-68%였다. 한편 부유부상이 진행됨에 따라서 리젝트 양의 증가폭이 둔화되는 경향을 나타내었다. 이러한 경향은 MCC의 소수성이 강할 수록 더욱 뚜렷하게 나타났다. 이를 통해 계 내로부터 소수성인 물질이 급속하게 제거됨을 알 수 있었으며 필요 이상의 부유부상 처리는 잉크제거 효율을 높일 수는 있으나 소모되는 시간에 비하여 비효과적임을 알 수 있었다.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.72-72
• /
• 2009

전자부품의 내부접속 및 파워반도체의 다이본딩과 같은 1차실장에는 고온환경에서의 사용과 2차실장에서의 재용융방지를 위해 높은 액상선온도 및 고상선온도를 필요로 하여, Pb-5wt%Sn, Pb-2.5wt%Ag로 대표되는 납성분 85%이상의 고온솔더가 널리 사용되고 있다. 생태계와 인체에 대한 납의 유해성이 보고된 이래, 무연솔더에 대한 연구가 활발히 진행되어 왔으나, Sn-Ag-Cu계로 대표되는 Sn계 합금으로 대체 중인 중온용 솔더와는 달리, 고온용 솔더에 대해서는 대체합금에 대한 연구가 미흡한 실정이다. 대체재의 부재로 인해 기존의 납을 다량함유한 솔더로 1차실장이 지속됨으로서, 2차실장의 무연화에도 불구하고 전자부품 및 기기의 재활용에 큰 어려움을 겪고 있다. 지금까지 고온용 무연솔더로서는 융점에 근거해 Au-(Sn, Ge, Si)계, Bi-Ag계, Zn-(Al, Sn)계의 극히 제한된 합금계만이 보고되어 왔다. Au계 솔더는 현재 플럭스를 사용하지 않는 광학, 디스플레이 분야 등 고부가가치 공정에 사용되고 있으나, 합금가격이 매우 비싸며 가공성이 나빠 대체재료로서는 적합하지 않다. Bi-Ag계 솔더 또한 취성합금으로 와이어 및 박판으로 가공하는데 어려움이 크며, 솔더로서 중요한 특성중 하나인 전기전도도 및 열전도도가 나쁜 편이다. 이에 비해, Zn계 합금은 비교적 낮은 합금가격, 적절한 가공성과 뛰어난 인장강도, 우수한 전기전도도 및 열전도도를 지녀, 고온용솔더 대체재료의 유력한 후보로 생각된다.이전 연구에서, 필자의 연구그룹은 Zn-Sn계 합금을 고온용 무연솔더로서 제안한 바 있다. Zn-Sn계 합금은 충분히 높은 융점과 함께, 금속간화합물이 없는 미세조직, 우수한 기계적 특성, 높은 전기전도도 및 열전도도 등의 장점을 나타내었다. 본 연구에서는 기초합금특성상 고온솔더로서 다양한 장점을 지닌 Zn-30wt%Sn합금을 고온용 솔더의 대표적인 적용의 하나인 다이본딩에 적용하여, 접합부의 강도 및 미세조직, 열피로 신뢰성에 대해 분석을 함으로서 실제 공정에의 적용가능성에 대해 검토하였다. Zn-30wt%Sn을 이용해 Au/TiN(Titanium nitride) 코팅한 Si다이를 AlN-DBC(aluminum nitride-direct bonded copper)기판에 접합한 결과, 양측에 완전히 젖은 기공이 없는 양호한 다이접합부를 얻었으며, 솔더내부에는 금속간화합물을 형성하지 않았다. Si다이와의 계면에는 TiN만이 존재하였으며, Cu와의 계면에는 Cu로부터 $Cu_5Zn_8,\;CuZn_5$의 반응층을 형성하였다. 온도사이클시험을 통한 열피로특성평가에서, Zn-30wt%Sn를 이용한 다이접합부는 1500사이클 지점에서 Cu와 Cu-Zn금속간화합물의 사이에서 피로균열이 형성되며, 접합강도가 크게 감소하였다. 열피로특성 향상을 위해 Cu표면에 TiN코팅을 하여 Zn-30wt%Sn 솔더로 다이접합한 결과, Si다이와 기판 양측에 TiN만으로 구성된 계면을 형성하였으며, TEM관찰을 통해 Zn-30wt%Sn과 극히 미세한 접합계면이 형성하고 있음을 확인하였다. Zn-wt%30Sn솔더와 TiN층의 병용으로 2000사이클까지 미세조직의 변화 및 강도저하가 없는 극히 안정된 고신뢰성의 다이접합부를 얻을 수가 있었다.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.49 no.4
• /
• pp.497-504
• /
• 2022

The purpose of this study is to evaluate the antibacterial effects of two liquid fluoride materials on Streptococcus mutans (S. mutans). Riva star aqua^TM (SDI, Bayswater, Australia), which consists of silver fluoride (AgF, step 1) and potassium iodide (KI, step 2), and Fluor protector^® (FP; Ivoclar Vivadent, Liechtenstein) were used for experimental groups. Experimental groups were divided into 4 groups : AgF, KI, AgF + KI and FP. For the positive control (PC) group, ampicillin was used, and the negative control group (NC) did not receive any additional treatment. Each group was divided into 30 and 50 µL groups by volume of liquid and applied to flat-coated S. mutans. The diameter of the zone of inhibition was measured. The PC and AgF groups showed larger diameters than other materials (p < 0.05), and the AgF group showed no significant difference from the PC group in the 50 µL group (p > 0.05). The FP group showed larger diameters than the AgF + KI group in the 30 µL (p = 0.009). The KI group did not show significant difference from the NC group (p > 0.05). AgF is comparable to ampicillin in antibacterial effects on S. mutans, and better than FP.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.98-104
• /
• 2023

The feasibility of an efficient process proposed for Cu-Cu flip-chip bonding was evaluated by forming a porous Cu layer on Cu pillar and conducting thermo-compression sinter-bonding after the infiltration of a reducing agent. The porous Cu layers on Cu pillars were manufactured through a three-step process of Zn plating-heat treatment-Zn selective etching. The average thickness of the formed porous Cu layer was approximately 2.3 ㎛. The flip-chip bonding was accomplished after infiltrating reducing solvent into porous Cu layer and pre-heating, and the layers were finally conducted into sintered joints through thermo-compression. With reduction behavior of Cu oxides and suppression of additional oxidation by the solvent, the porous Cu layer densified to thickness of approximately 1.1 ㎛ during the thermo-compression, and the Cu-Cu flip-chip bonding was eventually completed. As a result, a shear strength of approximately 11.2 MPa could be achieved after the bonding for 5 min under a pressure of 10 MPa at 300 ℃ in air. Because that was a result of partial bonding by only about 50% of the pillars, it was anticipated that a shear strength of 20 MPa or more could easily be obtained if all the pillars were induced to bond through process optimization.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.10
• /
• pp.845-854
• /
• 2009

There has been increased concern regarding the release of antibiotics to different environmental compartments due to the possibility of the development of antibiotic resistant bacteria. However, limited information is available regarding the occurrence, fate, and transport of antibiotics in Korea in both the aqueous phase and in solid phases such as sediment and soil. Therefore, this study was conducted to monitor the concentration of released antibiotics in surface water, sediment, and soil adjacent to a cattle manure composting facility in Korea. Specifically, the following six antibiotics were monitored: tetracycline (TC), chlortetracycline (CTC), oxytetracycline (OTC), sulfamethazine (SMT), sulfamethoxazole (SMX), and sulfathiazole (STZ). To extract and quantify the antibiotics from different environmental compartments, solid phase extraction (SPE) and high performance liquid chromatography mass spectrometry (HPLC/MS) techniques were adopted. The concentration of the six antibiotics ranged from below the detection limit (BDL) to 0.71 ${\mu}g$/L in surface water, from BDL to 27.61 ${\mu}g$/L in sediment, and from 0.12 to 157.33 ${\mu}g$/L in soil. In addition, higher concentrations of antibiotics were observed in surface water and sediment at locations closer to the composting facility indicating that composting is the source of the antibiotics found in the environment. Furthermore, higher concentrations of antibiotics were observed in the solid phase (sediment and soil) than the aqueous phase. These findings indicate that the possibility of antibiotic resistant bacteria is increased because such bacteria are more stable in the solid phase. Overall, longterm monitoring of the aqueous phase and solid phase is necessary to gain a better understanding of the impact of antibiotics from source on the environment in Korea.

• KSBB Journal
• /
• v.23 no.1
• /
• pp.90-95
• /
• 2008

In this study, a combined process of sequential anaerobic-aerobic digestion (SAAD), fluidized-bed bioreactor (FBBR), and ultrafiltration (UF) for the treatment of small scale food waste leachate was developed and evaluated. The SAAD process was tested for performance and stability by subjecting leachate from food waste to a two-phase anaerobic digestion. The main process used FBBR composed of aerators for oxygen supply and fluidization, three 5 ton reaction chambers containing an aerobic mesophilic microorganism immobilized in PE (polyethylene), and a sedimentation chamber. The HRTs (hydraulic retention time) of the combined SAAD-FBBR-UF process were 30, 7, and 1 day, and the operation temperature was set to the optimal one for microbial growth. The pilot process maintained its performance even when the CODcr of input leachate fluctuated largely. During the operation, average CODcr, TKN, TP, and salt of the effluent were 1,207mg/L, 100mg/L, 50 mg/L, and 0.01 %, which corresponded to the removal efficiencies of 99.4%, 98.6%, 89.6%, and 98.5%, respectively. These results show that the developed process is able to manage high concentration leachate from food waste and remove CODcr, TKN, TP, and salt effectively.

• Journal of Animal Environmental Science
• /
• v.18 no.2
• /
• pp.99-110
• /
• 2012

The purpose of the study is to collect basis data for to establish standard administrative processes of liquid fertilizer treatment. From this survey we could make out the key point of each step through a case of effective liquid manure treatment system in pig house. It is divided into six step; 1. piggery slurry management step, 2. Solid-liquid separation step, 3. liquid fertilizer treatment (aeration) step, 4. liquid fertilizer treatment (microorganism, recirculation and internal return) step, 5. liquid fertilizer treatment (completion) step, 6. land application step. From now on, standardization process of liquid manure treatment technologies need to be develop based on the six steps process.

• Korean Journal of Organic Agriculture
• /
• v.21 no.3
• /
• pp.451-465
• /
• 2013

This study was conducted to estimate Hanwoo carrying capacity when whole crop barley, rye, wheat and tritcale as winter forage crops was grown on different applying sources (chemical fertilizer, cattle or organic fertilizer) and mixed sowing combination with hairy vetch or forage pea during the period of 2011~2012. The experimental plots within whole crop barley or rye were consisted of 7 treatments, which were non-fertilizer, chemical fertilizer (P+K), chemical fertilizer (N+P+K), organic fertilizer, cattle slurry, cattle slurry with hairy vetch, and cattle slurry with forage pea. Each plot was triplicates and experimental treatments were allocated in the randomized complete block design. For whole crop barley, annual mean dry matter (DM) and total digestible nutrients (TDN) yields were the highest in N+P+K plots, but there were no significant differences among organic fertilizer, cattle slurry and mixed sowing with legumes. The TDN were the highest in mixed sowing plots of forage pea plus cattle slurry application. As 450 kg Hanwoo heifers were fed diets included 70% whole crop barley, organic fertilizer, cattle slurry application and mixed sowing plots of forage pea is capable of raising average 2.8 to 3.1 heads/ha a year. For whole crop rye, annual mean DM were the highest in N+P+K plots, but there were no significant differences among cattle slurry. Organic fertilizer application significantly increased TDN and relative feed value (RFV) in comparison with treatments of N+P+K fertilization as chemical fertilizers. In case of 450 kg Hanwoo heifers fed diets included 70% forage rye, it is estimated that cattle slurry application (mixed sowing with legumes) plots can rear average 2.8~ 3.2 heads/ha a year. For whole crop wheat, annual DM, crude protein, and TDN yields of application groups and mixed sowing treatment with legumes showed 6.90~7.44, 0.53~0.60 and 4.35~5.04 ton/ha, respectively. In case of 450 kg Hanwoo heifers fed diets included 70% forage rye, it is estimated that cattle slurry application (mixed sowing with legumes) plots can rear average 3.1~3.7 heads/ha a year. For Triticale, TDN yield was significantly (P<0.05) higher N+P+K plots, organic ferilizer, cattle slurry, cattle slurry with legumes than for no fertilizer and N+P+K plots. The Crude protein (CP) contents were the highest in mixed sowing plots of forage pea plus cattle slurry application. In case of 450 kg Hanwoo heifers fed diets included 70% forage triticale, it is estimated that cattle slurry application (mixed sowing with legumes) plots can rear average 3.4~3.7 heads/ha a year. It can be concluded that, on the basis of DM yield, not only mixed sowing with legumes by applying cattle slurry rather than single sowing of whole crop barley or whole crop rye enhanced production yield and feed values, but also it could be a substitute for imported grains as dietary protein sources in the case of feeding Hanwoo.