• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1900-1902
• /
• 2004

The degradation systems of non degradable waste water consist of the arc plasma torch, power supply, a feeder of liquid waste and reactors. Output of stable plasma torch, suitable air flux, microscopic atomizing state of waste water and long reaction section must be to degrade waste water more efficiently. In this paper, we are designed the stable power system, the microscopic atomizing state of waste water and the efficient reactors to satisfy various conditions. Non degradable wast water used in this work was $Na_2$EDTA of 1.0 mol. The concentration of $CO_2$ and EDTA was analyzed using GC (Gas Chromatography) and HPLC (High Performance Liquid Chromatography). In the result show that $CO_2$ concentration was about 96% and EDTA was degraded approximately 96%.

• 한국생물공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.272-276
• /
• 2005

Food wastewater derived from three-stages methane fermentation system showed high concentrations of sCOD, T-N and $NH_{3}-N$. To treat the organic wastewater, the optimal operating conditions for high efficiency $UV/TiO_{2}$ photocotalytic system have been investigated. In the first process, wastewater was pre-treated with $FeCl_{3}. The optimum pH and concentration for coagulation were 4.0 and 2000 mg/L, respectively. Through this process, 52.6% of $COD_{cr}$ was removed. The second process was $UV/TiO_{2}$ photocatalytic reaction. The optimum conditions for the operation of $UV/TiO_{2}$ photocatalytic system developed in this lab have been studied. In this process, CODcr was removed from 2890 to 184 mg/L and T-N was removed from 2496 to 914 for 24 hours, respectively.

• Nuclear Engineering and Technology
• /
• v.27 no.1
• /
• pp.25-32
• /
• 1995

Batch sorption experiments were conducted to investigate the sorption characteristics of $^{137}$ Cs, known for the primary target of safety assessment in low-level radwaste disposal, onto domestic rocks such as Granite and Tuff. A response surface analysis method was applied to quantify the effect of 3 independent variables (［Cs］, ［Vol/Wt］, ［pH］) on the sorption. Ac a result, initial Cs concentration appeared to be the most important variable within the range of the study. A significant effect of ［Vol/Wt］ on Kd was observed. The sorption of Cs was pH-insignificant. The sorption extent of nuclides onto tuff was more significant than that onto granite. The pH-insignificant sorption behavior of Cs was discussed in terms of the surface electrical properties and the solution chemistry. The sorption tendency of nuclides onto geomedia studied was interpreted by adopting the water structure modification theory.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.309-316
• /
• 2003

EAF(Electric Arc Furnace) Dust classified as special wastes containing heavy metal contaminants may cause to damage an environment such as underground water contamination if they were not treated properly. The possibility of producing the porous sintered body made from EAF Dust/clay composition system was studied. Mixing of EAF Dust and clay was carried out using wet-mixing process and two different sintering methods such as rapid and normal heat treatment were tried. By observing density, porosity and microstructure of sintered bodies, it was found that the bloating phenomenon depend on the contents of C, where the liquid phase occur or not during the sintering process. To obtain a light-aggregate of porous body due to bloating, the rapid heating was better than the normal heating at sintering process.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.494-500
• /
• 2003

The effects of $Al_2$O$_3$ addition upon the sintering range of clay-EAF dust (the specified wastes produced from steel making process) system body which would be used as a constructing bricks were investigated. The slope of apparent density to sintering temperature decreased for Clay-dust body containing 5~15 wt% A1203 sintered at 1200-125$0^{\circ}C$, and the absorption(%) of specimen sintered above 125$0^{\circ}C$ decreased due to the formation of open pores produced by pore bloating. For the specimen without any $Al_2$O$_3$ addition sintered at 1275$^{\circ}C$, the major phase was cristobalite, the small amount of mullite (3Al$_2$O$_3$ 2SiO$_2$) formed and the hematite (Fe$_2$O$_3$) remained. In the Clay-dust system body containing $Al_2$O$_3$ 15 wt%, however, the cristobalite disappeared and the major phase was mullite. Also the part of $Al_2$O$_3$ reacted with hematite to form hercynite (FeAl$_2$O$_4$). From the these results, addition of $Al_2$O$_3$ to Clay-dust system body enlarges a sintering range; decreasing an apparent density and absorption slop to sintering temperature owing to consumption of liquid phase SiO$_2$ at higher temperature and gas-forming component Fe$_2$O$_3$ at reduced atmosphere which would decrease an amount of liquid formed and increase the viscosity of the liquid produced during the sintering process.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.3
• /
• pp.221-227
• /
• 2007

Fenton's reagent is applied to directly decompose the ion-exchange resins, IRN-78 and the mixed resin with IRN-77. The newly applied procedures is to dry the resin first and the catalyst solution is completely absorbed into the resin, then a limited dose of $H_2O_2$ is introduced for an effective reaction between the reagents within the resin. As a characteristic on the decomposition of IRN-78, the resin mixture should be heated to $40^{\circ}C$ to induce the initial reaction and lag time is also needed for about 20 minutes until the main reaction occurs. The effectiveness of the decomposition is investigated using $CuSO_4,\;Cu(NO_3)_2\;and\;FeSO_4$ as a catalyst and the decomposition rate is compared depending on the concentration of each catalyst and the amount of $H_2O_2$. The most effective catalyst was found to be $FeSO_4$ for IRN-78 alone and the mixed resin with IRN-77, and $FeSO_4$ showed a special effect that the reaction was initiated without heating and a lag time. Furthermore, the optimum concentration of the catalyst for each resin and the mixed one is suggested in the view point of the amount of $H_2O_2$ needed and the stability of the decomposition reaction.

• Clean Technology
• /
• v.29 no.3
• /
• pp.200-216
• /
• 2023

Ginkgo leaves are considered waste biomass and can cause problems due to the strong insecticidal actions of ginkgolide A, B, C, and J and bilobalide. However, Ginkgo leaf biomass has high organic matter content that can be converted into fuels and chemicals if suitable technologies can be developed. In this study, the effect of pyrolysis temperature, minimum fluidized velocity, and Ginkgo leaf size on product yields and product properties were systematically analyzed. Fast pyrolysis was conducted in a bubbling fluidized bed reactor at 400 to 550℃ using silica sand as a bed material. The yield of pyrolysis liquids ranged from 33.66 to 40.01 wt%. The CO₂ and CO contents were relatively high compared to light hydrocarbon gases because of decarboxylation and decarbonylation during pyrolysis. The CO content increased with the pyrolysis temperature while the CO₂ content decreased. When the experiment was conducted at 450℃ with a 3.0×U_mf fluidized velocity and a 0.43 to 0.71 mm particle size, the yield was 40.01 wt% and there was a heating value of 30.17 MJ/kg, respectively. The production of various phenol compounds and benzene derivatives in the bio-oil, which contains the high value products, was identified using GC-MS. This study demonstrated that fast pyrolysis is very robust and can be used for converting Ginkgo leaves into fuels and thus has the potential of becoming a method for waste recycling.

• Nuclear Engineering and Technology
• /
• v.16 no.2
• /
• pp.64-69
• /
• 1984

With regard to the radioactive waste disposal, adsorption properties and migration rates have been evaluated for Cs-137 and Sr-90 with the domestic clay sampled from Cnyang, Sanchong and Mooan. Sorption coefficients (Ksorp) were determined by batch experiments. The measured values of Ksorp were ranged from 8000 to 17,000 ml/gr for Cs-137 of 0.1$\mu$Ci/ml, and from 10,000 to 15,000m1/gr for Sr-90 of 0.l$\mu$Ci/ml. Remarkably, Mooan clay showed lower values of Ksorp than those of the others. This could be explained by the poor soprtion capacity of the quartz found only in the Mooan clay. For the quantitative analysis, sorption isotherm equations of Freundlich type were made with the obtained values of Ksorp. $C_{R}$=18.0 $C_{A}$$^{0.74}$ : Cs-137, $C_{R}$=0.84 $C_{A}$$^{0.45}$ : Sr-90. By introducing the BOX model combined with the above relationships, simulation of underground nuclide movement was carried out. The results showed that the domestic clays could be the effective backfill material for repositories.itories.ies.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.11 no.4
• /
• pp.114-119
• /
• 2003

The fermentative conversion of food wastes into probiotic feed was investigated by seeding of mixed inoculum of Lactobacillus acidophilus and Saccharomyces cerevisiae. After grinding finely, optimal fermentation conditions for aeration was investigated at $30^{\circ}C$, The viable cell count of lactic acid bacteria and yeast during fermentation were monitored by controlling aeration rate at each different aeration degree of 0v.v.m 0rpm, 0.25v.v.m 100rpm, 0.5v.v.m 200rpm, and 1v.v.m 500rpm respectively. The most active growth of the yeast was shown at 0.5v.v.m 200rpm as $4.5{\times}10^9CFU/m{\ell}$. By controlling aeration rate, the pH of the probiotics feed could be controlled between 4-5 for the enhancement of preservation characteristics and acceptability for cattle feeding.

• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.1059-1066
• /
• 2009

Recently, the amount of thermosetting plastic wastes has increased with the production of reinforced plastic composites and causes serious environmental problems. The epoxy resins, one of the versatile thermosetting plastics with excellent properties, cannot be melted down and remolded as what is done in the thermoplastic industry. In this research, a series of experiments that decompose epoxy resin and recover carbon fibers from carbon fiber reinforced epoxy composites applied to railway vehicles was performed. We experimentally examined various decomposition processes and compared their decomposition efficiencies and mechanical property of recovered carbon fibers. For the prevention of tangle of recovered carbon fibers, each composites specimen was fixed with a Teflon supporter and no mechanical mixing was applied. Decomposition products were analyzed by scanning electron microscope (SEM), gas chromatography mass spectrometer (GC-MS), and universal testing machine (UTM). Carbon fibers could be completely recovered from decomposition process using nitric acid aqueous solution, liquid-phase thermal cracking and pyrolysis. The tensile strength losses of the recovered carbon fibers were less than 4%.