• KSBB Journal
• /
• v.16 no.1
• /
• pp.48-53
• /
• 2001

Bovine serum albumin(BSA) was solubilized into the reverse micellar phase consisting of sodium bis(2-ethylhexyl) sulfosuccinate(AOT) and isooctane using the phase transfer method. Of particular interest in this study were the effects of pH and the added salt type and concentration on the solubilization efficiency. When univalent or divalent salts such as KCl, NaCl, $MgCl_2$, or $CaCl_2$ were added to the aqueous phase at a concentration of 0.1 M, maximum solubilization efficiency was attained at a pH ranging from 5 to 7, depending on the added salt type. Increased salt concentration up to 1 M resulted in an increased solubilization efficiency for $CaCl_2$ and NaCl, while the addition of $MgCl_2$ beyond 0.1 M showed an anomalous trend. Further, it was noteworthy that too a large extent the protein precipitated in the interface between the organic and aqueous phases at lower pHs and lower salt concentrations. The size of the reverse micelle water pool was estimated by measuring the molar ratio of the surfactant to the water, $W_0$. Irrespective of pH in the aqueous phase, the resulting value of $W_0$ was almost constant, eg., 20 for $MgCl_2$ . However, the value of $W_0$ decreased with increased salt concentration in the cases of KCl and $CaCl_2$.

• 한국가스학회:학술대회논문집
• /
• 2003.10a
• /
• pp.65-72
• /
• 2003

현행 가스법상 지상식 LNG 저장탱크에 있어서 일정 용량의 저장탱크 주위에는 액상의 가스가 누출된 경우에 그 유출을 방지할 수 있는 방류둑(Dike) 또는 이와 동등 이상의 효과가 있는 시설을 설치하도록 규정하고 있어, 실제로 모든 지상식 LNG 저장탱크에 대해서 별도의 방류둑 설치를 의무화하고 있다. 또한, 예외규정으로 국제기준(international codes and standards)에 의해 설계되는 저장탱크는 심의를 통해 방류둑 기능을 인정할 수 있도록 하고 있다. 외국의 경우 LNG 저장탱크는 일반적으로 자국내 법령보다는 국제기준에 의해 건설됨으로써 1차 탱크로부터 일정거리의 둘레에 방류둑이 필요한 단일방호식 저장탱크 이외에 이중방호식, 완전방호식(full-containment) 및 멤브레인식(membrane) 저장탱크의 경우 외부(콘크리트, 강재)탱크가 방류둑 기능을 가지고 있어 별도의 방류둑이 필요없는 구조로 규정하고 있다. 멤브레인 LNG 저장탱크의 경우 프랑스, 일본 및 한국이 설계기술을 보유하고 있고, 최근 프랑스 및 한국에서 별도의 방류둑 없는 지상식 멤브레인 저장탱크 건설이 추진되고 있으나 양국 모두 자국법의 방류둑 규정에 의해 건설의 장애요소로 작용하고 있다. 따라서 지상식 멤브레인 LNG 저장탱크의 방류둑 기능에 대한 각 국의 법령 및 기준을 조사하고, 방류둑 일체형 저장탱크(완전방호식 및 멤브레인 저장탱크)의 형식별 안전성 평가 자료를 비교 검토함으로써 방류둑 일체형 멤브레인 저장탱크의 국내 도입의 타당성을 검토하고자 하였다. 조사결과 유럽, 미국 및 일본에서는 이중벽 LNG 저장탱크의 경우 콘크리트 외부탱크가 방류둑 기능을 가지는 것으로 규정하고 있으며, 특히 EN 1473과 제정중인 prEN 265002에서는 멤브레인 저장탱크의 경우 내부 멤브레인 탱크 누출시 단열시스템과 함께 외부 콘크리트 탱크가 액밀성 및 기밀성을 동시에 가지는 것으로 별도의 방류둑이 불필요함을 규정하고 있다. 프랑스 및 일본의 방류둑 일체형 LNG 저장탱크에 대한 위험성 평가 결과를 검토한 결과 멤브레인 저장탱크와 완정방호식 저장탱크는 안전성 차원에서 거의 동일한 것으로 나타났다. 따라서 국내에서 개발한 지상식 멤브레인 LNG 저장탱크 설계모델에 대한 안전성 제고 및 안전성 평가 등을 통해 객관적인 안전성 근거가 확보된다면 동 탱크의 경우에도 완전방호식 LNG 저장탱크와 같이 외부콘크리트 저장탱크의 방류둑 기능인정이 가능할 것으로 판단된다.

• Journal of the Korean Ceramic Society
• /
• v.41 no.10 s.269
• /
• pp.777-782
• /
• 2004

In this research, $5\times5cm^2$ unit cells were fabricated via liquid condensation process and uniaxial pressing followed by the screen printing of electrolyte and cathode layer. The SOFC stack was assembled with unit cells, gasket-type sealant and metal interconnect. The stack was designed to have a single column with internal-manifold and cross-flow type gas-channels. The SOFC stack produced 15 W, which is $50\%$ of the maximum power being expected from the maximum power density of the unit cell. Controlling factors for the proper operation of the SOFC stack and other designing factors of stack manifold and gas channels were discussed.

• KSBB Journal
• /
• v.22 no.5
• /
• pp.328-335
• /
• 2007

In this work ursolic acid (UA), a poorly water-soluble compound, was inclusion complexed with 2-hydroxypropyl-$\beta$-cyclodextrin (HP-$\beta$-CD) by various methods such as kneading, solvent evaporation and two types of supercritical fluid processes. The solubility and characteristics of these UA/HP-$\beta$-CD complexes were investigated by scanning electron microscopy, x-ray diffraction and HPLC. The water solubilities of the two complexes obtained from solvent evaporation and ASES processes were observed to increase up to 6$\sim$240 folds and 12$\sim$56 folds, respectively, compared with that of unprocessed UA. The stability of UA/HP-$\beta$-CD complex samples in cosmetic formulations was examined at various temperatures for one month. The UA/HP-$\beta$-CD complex prepared by solvent evaporation was found to be most stable among all the cosmetic formulations tested in our experiments.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.109-114
• /
• 2003

The purpose of this study Is to investigate the effect of $V_2$O$_{5}$ addition on the microstructures and magnetic properties of 7.7${\times}$4.5${\times}$1.0 mm sized multi-layer chip inductors prepared by the screen printing method using 0∼0.5 wt％ $V_2O_{5}$-doped NiCuZn ferrite pastes. With increasing the $V_2O_{5}$ content, the exaggerated grain growth of ferrite layers was developed due to the promotion of Ag diffusion and Cu segregation into the grain boundaries oi ferrites, which affected significantly the magnetic properties of the chip inductors. After sintering at $900^{\circ}C$, the inductance at 10 MHZ of the 0.5 wt％ $V_2O_{5}$-doped chip inductor was 3.7 ${\mu}$H less than 4.2 ${\mu}$H of the 0.3 wt% $V_2O_{5}$-doped one, which was thought to be caused by the residual stress at the ferrite layers increased with the promotion of Ag diffusion and Cu segregation. The quality factor of the 0.5 wt% $V_2O_{5}$-doped chip inductor decreased with increasing the sintering temperature, which was considered to be caused by the electrical resistivity of the ferrite layer decreased with the promotion of Ag/cu segregation at the grain boundaries and the growth of the mean grain size of ferrite due to exaggerated grain growth of ferrite layers.

• Applied Chemistry for Engineering
• /
• v.5 no.1
• /
• pp.160-175
• /
• 1994

Fibrous potassium hexatitanate whisker with the size of $ID=0.5{\sim}1{\mu}m$ and length=$100{\sim}1000{\mu}m$ (aspect ratio=100~1000) was produced through the reaction between titanium dioxide and potassium carbonate using the slow-cooling calcination followed by water leaching treatment. The optimum condition for the production of fibrous potassium titanate was calcination temperature of $1100^{\circ}C$ for 5hrs, $TiO_2$ mole ratlo to $K_2CO_3$ of 4.5 and slow-cooling rate of $0.5^{\circ}C/min$ to $860^{\circ}C$. Fibrous crystal are grown by the association between the solid potassium titanate and liquid phase during the slow-cooling process. The Proper water leaching condition for removing of K component was leaching time of 10hrs in boiling water. Pressurizing of the mixture of $K_2CO_3$ and $TiO_2$ to be calcinated became effective on the growth of fibrous crystal.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.393-405
• /
• 2020

Various geotechnical information is required to evaluate the stability of the ground and a foundation once liquefaction occurs due to earthquakes, such as the soil strength and groundwater level. The results of the Standard Penetration Test (SPT) conducted in Korea are registered in the National Geotechnical Information Portal System. If geotechnical information for a non-drilled area is needed, geostatistics can be applied. This paper is about the feasibility of obtaining ground information by the Empirical Bayesian Kriging (EBK) method and the Inverse Distance Weighting Method (IDWM). Esri's ArcGIS Pro program was used to estimate these techniques. The soil strength parameter of the drilling area and the level of groundwater obtained from the standard penetration test were cross-validated with the results of the analysis technique. In addition, Multichannel Analysis of Surface Waves (MASW) was conducted to verify the techniques used in the analysis. The Buk-gu area of Pohang was divided into 1.0 km×1.0 km and 110 zones. The cross-validation for the SPT N value and groundwater level through EBK and IDWM showed that both techniques were suitable. MASW presented an approximate section area, making it difficult to clearly grasp the distribution pattern and groundwater level of the SPT N value.

• Resources Recycling
• /
• v.13 no.1
• /
• pp.28-38
• /
• 2004

The characteristics of cyanide decomposition in aqueous phase by electric oxidization have been explored in an effort to develop a process to recycle waste water. Considering current efficiency and voltage, the free cyanide decomposition experiment by electric oxidization indicated that 5 V of voltage and copper catalytic Cu/CN mole ratio 0.05 was the most appropriate condition, where current efficiency was 26%, and decomposition speed was 5.6 mM/min. High voltage and excess copper addition increased decomposition speed a little bit but not current efficiency. The experiment of free cyanide density change proves that high density cyanide is preferred because speed and current efficiency increase with density. Also, the overall decomposition reaction could be represented by the first order with respcect to cyanide with the rate constant of $1.6∼7.3${\times}$10^{-3}$ $min^{-1}$ The mass transfer coefficient of electric oxidization of cyanide came out as $2.42${\times}$10^{-5}$ $min^{-1}$ Furthermore, the Damkohler number was calculated as 5.7 in case of 7 V and it was found that the mass transfer stage was the rate determining step.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.331-338
• /
• 2008

Coal-tar enamel, blown asphalt and polyethylene have been used as wrapping materials of steel pipe in Korea. Currently, every manufacturer produces wrapped steel pipes with different materials and methods, and little research has been performed to get on wrapping methods and materials. In this research, properties of wrapping material of steel pipe used for water supply have been evaluated. All of the materials tested in this work were found to meet the standard. Among the wrapping materials of steel pipe tested, blown asphalt and coal-tar enamel were reasonable in price, and their mechanical properties were excellent. The quality of the wrapped steel pipes was being melted easily in organic solvent. When coated thick, the load of the steel pipes was higher than necessary. Tensile strength of cathode exfoliation and PE 3-layer wrapping method was excellent. The pulling intensity of T-Die PE 3-layer was stronger than PE fluidized in PE wrapping method. Cathode exfoliation area was smaller than PE fluidized. Mechanical property and thermo-property of T-Die PE 3-layer were excellent and its anti-chemical property was great. Liquid epoxy can change the property of coating materials depending on the hardening condition and resin selection. Polyurethane used in this test showed a less adhesive strength with steel pipes than epoxy. Moisture absorbance rate was higher than Epoxy's, however. To utilize polyurethane as wrapping materials, basic property of the matter should be improved followed by finding the best suited coating condition. The method of PE 3-layer by extrude method appeared to be the best in this study. However, identification of other wrapping materials requires further additional tests.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2006.04a
• /
• pp.166-170
• /
• 2006

본 연구에서는 폐광산 주변에 산재되어 있는 광미/광폐석을 처리하기 위하여 고형화 실증 실험을 수행하였다. 고형화 공정에서 흔히 사용하는 포틀랜드 시멘트와 MSG-E, MSG-N을 고화제로 사용하였으며 현장 광미 및 광폐석을 대상으로 고화체를 양생하고 고화체의 압축강도 및 중금속 용출 정도를 측정하였다. 고화체의 물리/화학적 특성을 비교하기 위해 광미/고화제 비율, 배합수/고화제 비율 그리고 고화체 양생기간을 실험인자로 설정하였다. 실험 결과 광미/고화제의 비율 1:1 만을 고려하더라도 중금속 용출의 급격한 감소가 이루어지는 것을 확인할 수 있었으며 광미/고화제의 비율을 3:1 이하로 유지시키는 경우, 고화체의 압축강도가 현행 폐기물 관리법(20조 관련)에서 규정하고 있는 차단형 매립시설 내부막의 압축강도 기준인 $0.21kgf/mm^2$ 보다 높은 것으로 나타났다. 다양한 pH를 갖는 수용액에 대하여 시간에 따른 고화체의 중금속 용출률을 측정한 결과, 수용액의 pH가 1과 13인 강산/강염기 용액에서 일부 중금속의 용출 농도가 지하수 생활용수 기준치를 초과하였으나, pH와 3 - 11인 경우에는 중금속 용출률이 급격히 감소하여 모두 기준치 이하를 나타내었다. 또한, pH가 1과 13인 수용액의 경우에도 고화체와 반응하는 시간이 증가할수록 고화체의 buffering 효과에 의해 수용액의 pH가 감소하였다. 이러한 결과는 현장에서 접촉수의 pH가 강산이나 강염기라 하여도, 고화체의 buffering 효과에 의해 시간이 지남에 따라 수용액의 pH가 낮아져 고화체로부터의 중금속 용출은 매우 감소할 것임을 의미한다.ss of an active application defined using the model. The technique is developed in a platform- and language-independent way, and it is algorithmic and can be automated by computer program. We give an example dealing with network auction to illustrate the use of the model and the verification technique.품으로 내부 온도분포를 측정하였으며, 유한차분법 프로그램으로 대류열전달계수를 결정하였다. 대류열전달계수는 792에서 2,107 W/m$^2$로 분석되었다. 대류열전달 계수는 액상식품과의 상대속도가 증가함에 따라서 증가하였고, 점도가 증가함에 따라서는 감소하였다.ce of precision/recall of 90.99%/92.52%, and 93.39%/93.41% respectively. 의한 변성에 부분적으로 보호 작용을 나타 낼 것으로 추정된다.경(製麴72時間頃)의 활성(活性)은 보리쌀국(麴), 밀가루국(麴), 찹쌀국(麴), 고구마국(麴)의 순이었다.험 결과 오전용 사료는 관행적인 산란계 배합사료에서 Ca공급제를 제외한 것을 급여하고, 오후용 사료는 Ca공급제를 3배 첨가한 T2처리로 15:00~16:00시에 교체급여를 하면 사료섭취량 감소와 사료비 절감면에서 바람직할 것으로 사료되며, 고에너지-고단백질-저Ca의 분말사료와 저에너지-저단백질-고Ca의 펠렛사료를 혼합급여하면 산란계의 사료