• Composites Research
• /
• v.33 no.5
• /
• pp.247-250
• /
• 2020

In this study, the possibility of manufacturing a magnesium (Mg) composites reinforced with continuous silicon carbide (SiC) fibers was examined using a liquid pressing process. We fabricated uniformly dispersed SiC fiberAZ91 composites using a liquid phase pressing process. Furthermore, the precipitates were controlled through heat treatment. As a continuous Mg₂Si phase was formed at the interface between the SiC fiber and the AZ91 matrix alloy, the interfacial bonding strength was improved. The tensile strength at room temperature of the prepared composite was 479 MPa, showing excellent mechanical properties.

• Composites Research
• /
• v.32 no.1
• /
• pp.1-5
• /
• 2019

In this study, Al1050 composites reinforced with uniformly dispersed, high volume fraction $TiB_2$ particles were fabricated by liquid pressing process and analyzed to microstructure, mechanical properties. Hardness, ultimate tensile strength and compressive yield strength of the 56 vol.% $TiB_2$-Al1050 composite increased to 10, 4.5 and 9.8 times, respectively, compared with those of the Al1050 due to dispersion hardening effect of uniformly dispersed $TiB_2$ in the Al matrix.

• Applied Microscopy
• /
• v.29 no.3
• /
• pp.281-289
• /
• 1999

The stirred and thixoformed $SiC_p/AZ91HP$ Mg composites are studied on the basis of microstructural analysis using transmission electron microscopy (TEM). The products of interfacial reaction are identified as $Mg_2Si$, MgO and $Mg_{17}Al_{12}$ phases and the crystallized phases are found to be orthorhmbic $Al_6Mn$ and decagonal T phases. It is shown that $Mg_2Si$ and $Mg_{17}Al_{12}$ phases are found at the surface of $SiC_p$ and $Al_6Mn$ is found near interface and crystallized on the matrix. Phase identification is carried out by crystallographic work based on primitive cell volume, zero order Laue zone (ZOLZ) patterns and single convergent beam electron diffraction (CBED) patterns containing higher order Laue zone ring from a nanosized region.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.50-53
• /
• 2003

Carbon nannofiber reinforced Cu matrix composite has potential applications for electrically conducting materials having high strength and electrical conductivity. In this study, we have developed fabrication technology of the nanocomposites using a liquid pressing process. The process is to use the low pressure for infiltration of Cu melt into carbon nanofiber mat as the Cu melt is pressurized directly. The minimum pressure required for infiltration was calculated from force balance equation, permeability measurement and compaction behavior of carbon nanofiber. Also, the melting temperature and the holding time have been optimized.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.456-463
• /
• 2004

To enhance the performance of anode-supported SOFC, single cell fabrication procedure was changed for better and resulting power generating characteristics of single cell were investigated. Liquid condensation process was employed for the granulation of NiO/YSZ powder mixture and the produced powder granules were compacted into anode green substrate by uni-axial pressing. YSZ electrolyte was printed on green substrate via screen-printing method and co-fired at 1400$^{\circ}C$ for 3 h. LSM/YSZ composite cathode of which the composition and heat treatment condition was adjusted to minimize the polarization#resistance with AC-impedance spectroscopy, was screen printed. The final single cell size from this multi-step procedure was 5${\times}$5 $\textrm{cm}^2$ and 10${\times}$10 $\textrm{cm}^2$. The maximum power densities of 5${\times}$5 and 10${\times}$10 single cells were about 0.45 W/$\textrm{cm}^2$ and 0.22 W/$\textrm{cm}^2$ at 800$^{\circ}C$, which are two times superior than those from single cells fabricated by the conventional process in previous our work.