• Journal of the Korean Society of Safety
• /
• v.10 no.3
• /
• pp.120-129
• /
• 1995

Since the rate and completeness of combustion in direct injection engines were controlled by the characteristics of gas flow fields and sprays, an understanding of those was essential to the design of the direct injection engines. In this study the numerical simulations of swirl effects on the characteristics of gas flow fields and sprays were performed using the spray model that could predict the interactions between gas fields and spray droplets. The governing equations were discretized by the finite volume method and the modified k- e model which included the compressibility effects due to the compression/expansion of piston was used. The results of numerical calculation of the spray characteristics in the quiescent environment were compared with the experimental data. There were good agreements between the results of calculation and the experimental data, except in the early stages of spray. In the motoring condition, the results showed that a substantial air entrainment into the spray volume was emerged and hence the squish motion was relatively unimportant during fuel injection periods. As the swirl ratio increased, the evaporation rate was increased due to the wide dispersion of the spray droplets and the strong interaction between spray droplets and gas fields.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1229-1235
• /
• 2014

At the LPG vehicle air intake system, most of dust particles in the air cleaner are removed. However very small particles are not removed and accumulated. The accumulation of carbon in air intake system is going to affect the idle speed control and sensor signal. It also causes engine chattering and transmission troubles of automatic transmission. This is study about cleaning up intake system using cleaning chemical. We can clean up the intake system by spraying cleaning liquid onto intake device when the engine is idling after intake hose is removed from warmed up vehicle. We can obtain the following experimental results by cleaning up ISC, surge tank, intake manifold, intake valves and combustion chamber. According to this results, the stroll valve works correctly and power rate of engine is up to the standard, it is smoothy to control the idling speed when a vehicle pulls up. After cleaning up CO grow down about 0.15%, HC does about 20~100 ppm.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3276-3286
• /
• 1994

In most direct contact liquid-liquid heat exchangers, oil or hydrocarbon with a density less than water is normally used as dispersed working fluid. The main difficulty that arises with this arrangement lies in the control of the interface at the top of the column. When it is connected with a solar collector which uses water as its working fluid, the main difficulties arise from the fact that the water can be frozen during winter time. In order to solve these problems and to demonstrate the technical feasibility of a direct contact liquid-liquid heat exchanger, liquids heavier than water with low freezing temperature has been utilized as dispersed phase liquids in a small laboratory scale model made of pyrex glass. In the present investigation, dimethyl phthalate(C/sub 6/H/sub 4/)COOCH/sub 3/)/sub 2/) and diethyl phthalate (C/sub 6/H/sub 4/(CO/sub 2/C/sub 2/H/sub 5/)/sub 2/) are utilized as heavy dispersed phase working fluids. The results of the present investigation the technical in the utilization of heavier dispersed working liquid in the spray-column liquid-liquid heat exchanger for a solar system. The overall average temperature difference along the column is found to be almost half of the initial temperature difference between the dispersed and the continuous phase. Despite the fact that the two phthalates tested in the experiment differ significantly in some of their physical properties, the volumetric heat transfer coefficients in terms of dispersed fluid superficial velocities were found to be similar for both phthalates tested.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.66.1-66.1
• /
• 2011

반도체를 비롯하여 LCD, OLED와 같은 디스플레이 (FPD: Flat Panel Display) 분야는 국가 선도 사업으로써 발전을 거듭해오고 있다. 하지만 기술의 성숙도가 높아짐에 따라 최근 중국과 대만 업체와의 경쟁이 심화되고 있으며, 더불어 환경문제가 큰 이슈로 떠오르고 있어 신기술 개발을 통한 생산 수율 향상 및 친환경 공정 개발의 중요성이 커지고 있다. 반도체, 디스플레이 공정에서 생산 수율 저하의 주요 원인으로써 공정 중 발생하는 미세 오염 입자를 들수 있다. 반도체 및 디스플레이 공정에서 세정 기술은 전체 기술의 30% 이상을 차지하며 생산 수율 및 제품의 품질에도 큰 영향을 주는 공정이다. 세정 공정은 일반적으로 습식 세정 공정이 낮은 공정비용을 바탕으로 널리 적용되어 왔으나, 기판의 대형화와 패턴의 미세화에 따라 정밀한 세정 스펙이 요구되며 더불어 막대한 양의 초순수와 화학액의 사용으로 인한 공정비용 증가와 환경 규제 강화에 따른 폐수 처리의 문제에 직면하고 있다. 이에 따라 폐수의 양을 줄이며 건조공정을 필요로 하지 않아 공정비용을 줄일 수 있는 건식 세정 공정에 대한 연구가 활발히 진행 되고 있다. $CO_2$ snow jet 세정 기술은 건식 공정으로써 $CO_2$ 가스를 특수하게 제작된 분사 노즐에서 고압으로 가스를 분사하여 이 때 발생되는 순간적인 감압에 의한 단열 팽창으로 생성된 $CO_2$ snow 입자가 기판 표면의 오염물과 물리적 충돌을 하어 세정이 이루어지는 기술이다. 특히 $CO_2$ 세정은 환경과 인체에 무해하며 공정 후 바로 승화하기 때문에 추가적인 폐수처리 공정 등이 필요하지 않고, 건식 공정으로써 수세(Rinse) 공정을 필요로 하지 않기 때문에, 공정비용을 크게 줄일 수 있으며 물반점 발생을 방지 할 수 있는 친환경 건식 공정으로써의 장점을 가지고 있다. 본 연구에서는 자체적으로 개발한 $CO_2$ snow jet을 바탕으로 하여 다양한 공정조건을 변화시켜 세정효율을 측정하는 한편, 최적화 하기 위한 연구를 진행하였으며 더불어 $CO_2$ snow의 세정력을 정량적으로 평가하기 위한 연구를 진행하였다. 실험을 통해 가장 효과적으로 $CO_2$ snow 입자를 배출 할 수 있는 공정 조건으로써 5 bar의 캐리어 가스 압력을 사용하여, 세정력에 가장 큰 영향을 줄 수 있는 분사 노즐과 기판 사이의 거리 및 분사 노즐의 각도 등을 변화시켜 각 조건에 따른 세정효율을 평가하였다. 세정 오염물은 Silica, PSL 표준 입자(Duke scientific, USA)를 정량적으로 웨이퍼에 오염 시킨 후, 파티클 스캐너(Surfscan 6500, KLA-Tencor, USA)를 이용하여 세정 전 후의 오염입자 개수 변화를 통해 정량적으로 세정효율을 평가하였다. 본 연구를 통하여 $CO_2$ snow jet를 이용한 친환경 고효율 건식 세정 공정 메커니즘을 분석하였으며, 노즐과 기판 사이의 간격 및 분사 노즐의 각도 등을 최적화 한 세정 공정을 얻을 수 있었다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.7
• /
• pp.970-974
• /
• 2012

Prunus mume is said to aid in the recovery of fatigue and improvement of liver and stomach functions. To obtain the best benefits of the whole fruit, fresh green Prunus mume was de-seeded and the fruit pulp was vacuum dried. The vacuum-dried pulp was powdered and sieved through a 250 ${\mu}m$ sieve. Then the sieved green Prunus mume powder (GPP) was granulated with water (GPPGW) and with Prunus mume extract (GPPGE) with a fluid bed coater. The physicochemical and sensory properties of GPP, GPPGW, and GPPGE were then evaluated. As a result, the water dispersibility (dispersible time) of GPP, GPPGW, and GPPGE was 21.19 sec, 6.46 sec, and 4.85 sec, respectively. The powder fluency (angle of repose) of GPP, GPPGW, and GPPGE was $11.25^{\circ}$, $8.65^{\circ}$, and $9.52^{\circ}$, respectively. The overall consumer acceptance of GPP, GPPGW, and GPPGE was 3.50, 4.62 and 5.00, respectively. Inconclusion, Prunus mume can be used as granulated whole fruit pulp with good powder fluency and dispersibility.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.11
• /
• pp.3054-3062
• /
• 1995

Recently, the improvement of fuel economy and the reduction of exhaust smoke and NOx have been successfully achieved by supplying diesel engines with emulsified diesel oil with water particles. In the present paper, the difference between the combustion of injected emulsified fuel and that of diesel oil spray is clarified by means of taking high-speed and color photographs of the flames in the engine cylinder. As the results, the two kinds of fuels show different combustion behavior each other in the growth of initial flame and in the termination of combustion process in the cylinder. Then, suitable combustion chamber design for the use of emulsified fuel is discussed on the basis of experimental data for various distribution of spray in different kinds of piston cavities. Some methods of clearing troubles caused by emulsified fuel injection are also discussed on the basis of performance tests with a remodeling test engine.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.55-63
• /
• 2014

Pyrolysis oil (PO), also known as Bio crude oil (BCO), has the potential to displace significant amounts of fuels that are currently derived from petroleum sources. PO has been regarded as an alternative fuel for petroleum fuels to be used in diesel engine. However, the use of PO in a diesel engine requires modifications due to low energy density, high water contents, low acidity, and high viscosity of the PO. One of the easiest way to adopt PO to diesel engine without modifications is emulsification of PO with the fuels that has higher cetane number. However, PO that has high amount of polar chemicals is immiscible with non polar hydrocarbons of diesel. Thus, to stabilize a homogeneous phase of diesel-PO blends, a proper surfactant should be used. In this study, a DI diesel engine operated with diesel and diesel-PO emulsions was experimentally investigated. Performance and gaseous & particle emission characteristics of a diesel engine fuelled by diesel-PO emulsions were examined. Results showed that stable engine operation was possible with the emulsions and engine output power was comparable to diesel operation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.611-617
• /
• 1989

A jet cutting system is a new concept of cutting device wihch requires high pressure up to thousands of atmospheric pressure. The use of water as a cutting medium brings in many of working advantages such as no dust, no gas, and no thermal distortion. And an introduction of abrasives into the water jet flow increases signigicantly cutting abilities and improves cutting performance. Cutting with abrasive water jet involves many operating variables, including design of the cutting system. For efficient cutting, the operating parameters have to chosen properly. In spite of several attempts to develop the cutting model theoretically, all of the optimization of the operating parameters is based upon exerimental results of each jet cutting system. In this paper, the effect of the parameters was measured and analysed in terms of pressure, abrasive, and transverse rate of a workpiece. Most of all, sufficient feeding of abrasives is the most important factor for efficient cutting performance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.598-598
• /
• 2010

와이퍼 작동 중에 발생하는 진동소음 중 1000Hz 이상의 스퀼 소음은 발생 메커니즘이 정확하게 알려지지 않았으며 발생하는 조건도 불규칙하다. 이 스퀼 소음의 발생 빈도 및 주파수를 변경하는 설계를 위하여 스퀼 진동 소음의 발생 메커니즘의 원인분석이 우선적으로 이루어져야 한다. 이 논문에서는 자동차 와이퍼 시스템에서 워셔액을 분사하였을 때 발생하는 스퀼 소음을 측정하고 인자 별로 분석하였다. 스퀼 소음이 발생하는 인자들을 마찰계수와 연관이 있는 인자, 기하학적인 인자, 와이퍼의 운동과 관련된 인자들로 나누어 분석하였다. 실제 와이퍼 시스템을 구현하기 위하여 모터와 원판 지지대 등을 이용하였고, 마이크로폰, 레이저 바이브로미터, 노이즈북, 아르테미스를 이용하여 측정 및 분석하였다.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.131-135
• /
• 2001

The atomization characteristics of an annular liquid (water) sheet of small radius with a core gas (air) flow were studied. Different sizes of annular gaps (0.2, 0.4 and 0.8 mm) were tested to find the effect of liquid sheet thickness on SMD. The inner diameter of the gas port for the core gas flow was 4 mm. Cross-section averaged SMD was measured for various liquid and gas velocities. Regions of the SMD decrease with the increase of the liquid velocity always existed regardless of the liquid sheet thickness. This attributes to the transition of the flow patterns of spray and also to the aerodynamic interaction between the atomizing gas and the ripples on the liquid sheet surface.