• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.5
• /
• pp.429-435
• /
• 2020

This paper describes the experimental study of reverse-Brayton refrigeration system for application to high temperature superconductivity electric devices and LNG re-liquefaction. The reverse-Brayton refrigeration cycle is designed with operating pressure of 0.5 and 1.0 MPa, cooling capacity of 2 kW at 77 K, and neon as a working fluid. The refrigeration system is developed with multi scroll compressor, turbo expander and plate heat exchanger. From experiments, the performance characteristics of used components is measured and discussed for 77-120 K of operating temperature. The developed refrigeration system shows the cooling capacity of 1.23 kW at 77 K and 1.64 kW at 110 K.

• Journal of Power System Engineering
• /
• v.12 no.4
• /
• pp.5-11
• /
• 2008

The RI gasoline engine haying a sub-chamber had a high cycle variation due to the difficulty of the residual gas scavenge in the sub-chamber. To solve this problem and improve the combustion performance of RI engine, we devised a method to inject directly CNG fuel into the sub-chamber. A DI diesel engine of single cylinder was converted into a RI-CNG engine and an electronic control unit for the engine was manufactured. In this study, the combustion characteristics of the RI-CNG engine were investigated with the injection timings and air excess ratios at the load conditions of 50% throttle open rate and 1700rpm. As the results from this study, the RI-CNG engine worked reliably under the condition of the ignitable lean limit of $\lambda=1.7$ by showing the $COV_{imep}$ below about 5%. And the highest thermal efficiency could be obtained in the injection timing that produced the high imep and the low $COV_{imep}$ at the same time. The CO emission concentration indicated very low values and the THC and $NO_x$ showed an opposite pattern. With a view to improving the thermal efficiency and reducing the harmful emissions, the proper control region of the ignition timing and the mixture ratio were nearly ATDC $20^{\circ}\sim50^{\circ}$ and $\lambda=1.4$ respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.10
• /
• pp.887-894
• /
• 2016

The CNG pressure vessel is manufactured by a deep drawing and ironing (D.D.I) process for forming cylinder parts, followed by a spinning process for formation of the dome part. However, studies on the buckling phenomenon of the dome part and formation of the inlet part have not been performed yet, and the CNG pressure vessel is produced by the experience of the field engineers and the trial and error method. In this study, buckling phenomenon during the spinning process was predicted by comparing critical buckling loads obtained through theoretical analysis with axial loads from the FEA, and a method for preventing buckling of the dome part was proposed by employing commercial software (Forge NxT 1.0.2). Also, to form the inlet part, forming loads of the roller at contact point between the roller and the dome part were analyzed according to radii of the dome part, and the inlet part was formed by controlling the radius of the dome part.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.176.1-176.1
• /
• 2011

세계적으로 석유 기반 자원의 고갈에 따른 부족, 기후변화협약 및 환경규제 강화에 의해 세계적으로 바이오소재를 이용하고자 하는 연구와 더불어 유리강화복합재료의 대체물질로 적합한 천연섬유를 보강재로 사용하는 바이오복합재료의 연구 또한 활발하게 진행되고 있다. 최근 새로운 신재생에너지원으로 각광 받고 있는 바이오에너지 중 해조류는 가장 자연친화적이고 생산력이 뛰어난 바이오매스로 알려져 있다. 해조류는 바닷물 속에 녹아 있는 탄소를 흡수할 뿐만 아니라 광합성을 통해서도 탄소를 흡수하면서 성장하기 때문에 탄소흡수원의 역할을 하게 되며, 해조류 바이오에너지를 생산할 경우 화석연료를 대체하여 지구온난화의 주범인 온실가스를 감축하는 기능을 한다. 본 연구에서는 해조류를 이용한 바이오에너지 생산 공정에서 2차적으로 발생하는 부산물을 보강재로 사용한 바이오복합재료의 제조와 제조된 바이오복합재료의 열적 특성 및 동역학적 특성을 분석하였다. 해조류 부산물의 화학적 전처리에 따른 Thermogravimetric analysis(TGA) 분석 결과로 cellulose 함량이 가장 높고 불순물이 적은 황산 처리한 파래를 이용해 파래/Polypropylene(PP) 바이오복합재료를 다양한 보강비율 (20-50wt%)로 압축성형 하였다. 파래/PP 바이오복합재료의 저장탄성률은 파래 함량이 40wt%일 때 4.0 Gpa으로 최대값을 보였으며 이는 PP 매트릭스와 비교했을 때 약 8.1% 향상된 결과이다. 파래/PP 바이오보합재료의 열팽창 특성은 파래 함량이 증가함에 따라 열팽창계수가 낮아지는 경향으로 50wt%일 때 가장 낮은 값을 나타내었으며 이는 PP 매트릭스와 비교했을 때 약 56% 향상된 결과이다. 따라서 비생분해성 고분자에 새로운 신재생 바이오매스인 해조류를 보강재로 사용하여 열적 특성 및 동역학적 특성이 향상된 친환경적인 바이오복합재료의 제조 가능성을 확인하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.193-200
• /
• 2007

Natural gas is one of the most promising alternatives to gasoline and diesel fuels because of its lower harmful emissions, including $CO_2$, and high thermal efficiency. In particular, natural gas is seen as an alternative fuel for heavy-duty Diesel Engines because of the lower resulting emissions of PM, $CO_2$ and $NO_x$. Almost all CNG vehicles use the PFI-type Engine. However, PFI-type CNG Engines have a lower brake horse power, because of reduced volumetric efficiency and lower burning speed. This is a result of gaseous charge and the time losses increase as compared with the DI-type. This study was conducted to investigate the effect of injection conditions (early injection mode, late injection mode) on the combustion phenomena and performances in the or CNG Engine. A DI Diesel Engine with the same specifications used in a previous study was modified to a DI CNG Engine, and injection pressure was constantly kept at 60bar by a two-stage pressure-reducing type regulator. In this study, excess air ratios were varied from 1.0 to the lean limit, at the load conditions 50% throttle open rate and 1700rpm. The combustion characteristics of the or CNG Engine - such as in-cylinder pressure, indicated thermal efficiency, cycle-by-cycle variation, combustion duration and emissions - were investigated. Through this method, it was possible to verify that the combustion duration, the lean limit and the emissions were improved by control of injection timing and the stratified mixture conditions. And combustion duration is affected by not only excess air ratio, injection timing and position of piston but gas flow condition.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.6
• /
• pp.514-520
• /
• 2018

Polyurethane foam has excellent mechanical strength and insulation performance, and has been adopted as an insulation material for $-163^{\circ}C$ liquefied natural gas carrier. In this study, Kevlar Polyurethane Foams(K-PUF) were synthesized by adding Kevlar pulp with excellent mechanical strength for the purpose of improving the performance of existing polyurethane foam. Since polyurethane foam has mechanical performance depending on the proportions of Kevlar pulp added, the mechanical strength of the K-PUF with ratios of fiber0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.% and 1.0wt.%) was evaluated. The compression tests were performed on the 4 different temperatures($20^{\circ}C$, $-50^{\circ}C$, $-110^{\circ}C$ and $-163^{\circ}C$) in consideration of the environmental characteristics as a cryogenic insulation used in LNG carrier. Besides, the effects of the fiber addition on polyurethane foam with closed cell structure were evaluated in a phenomenological approach through SEM analysis. All the results were compared to Neat-polyurethane foam. As a results, 0.8wt.% K-PUF showed the improved mechanical strength, and the addition of Kevlar pulp in a certain ratio improves the mechanical performance by enhancing the compression resistance.

• Composites Research
• /
• v.32 no.5
• /
• pp.290-295
• /
• 2019

In the present study, composite insulation mat was reinforced over polyurethane foam (PUF) to improve the thermal performance and impact resistance of the PUF applied to the liquefied natural gas carrier insulation system. The composite insulation mat used Kevlar, aerogel, and cryogel composite mat that can be applied in a cryogenic environment. The thermal conductivity was measured at $20^{\circ}C$ to investigate the thermal performance, and the drop impact test was carried out under impact energy of 30 J at $20^{\circ}C$, $-163^{\circ}C$ to investigate the impact resistance. The measured thermal performance was compared with neat PUF through effective thermal conductivity theoretical value. The shock resistance was evaluated of contact force, contact time, and absorb energy. In experimental results, cryogel composite mat was the best performance in terms of thermal performance, and aerogel composite mat was the best performance in terms of impact resistance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.133-140
• /
• 2016

The Ministry of Land, Infrastructure and Transport has introduced low-floor buses, which are convenient for passengers getting on and off the bus and for the handicapped. The standard bus model is 11 m long and uses compressed natural gas (CNG). However, this model has drawbacks in narrow rural road conditions such as those in farming and fishing villages and mountainous areas, as well as difficulty in refueling since CNG facilities are not readily available. In this study, running resistance values were obtained by coasting performance tests on actual roads using a Tata Daewoo LF-40 model with three different weight conditions: curb vehicle weight (CVW), half vehicle weight (HVW), and gross vehicle weight (GVW).The test methods include WHVC, NIER-06, and constant-speed driving at 60 km/h. These tests were used to measure the fuel economy of vehicles other than the target vehicles to obtain the combined fuel economy. The energy efficiency was highest in the case of CVW. In the WHVC mode, the fuel consumption rates of HVW and GVW were typically 3.5% and 12% higher than that of CVW, respectively. In constant-speed driving, the fuel efficiency of HVW was higher than that of CVW. Further research is required to analyze the exhaust gas data.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.865-873
• /
• 2013

The deep drawing and ironing (DDI) process involving the use of a high-capacity horizontal press is used for manufacturing acompressed natural gas (CNG) pressure vessel. However, some variables of the DDI process have been determined based on the experiences of workers, and the short die life needs to be improved for manufacturing the pressure vessel withhighquality and lowcost. In this study, process variables such as the draw ratio, distance between dies, radius of rounding of drawing die, and angle of ironing die are chosen to enhance the reliability and improve the die life based on previous studies and experiences. The draw ratio limits at which no tearing or wrinkling occurs are determined using FEA, and the distances between dies, radius of rounding of drawing die, and angle of ironing die are optimized by the DOE method. The results of the optimal process variables are compared with those of the existing DDI process for verifying their effectiveness.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.5
• /
• pp.332-340
• /
• 2015

Acoustic emission (AE) is an effective nondestructive test that uses transient elastic wave generated by the rapid release of energy within a material to detect any further growth or expansion of existing defects. Over the past decades, because of environmental issues, the use of compressed natural gas (CNG) as an alternative fuel for vehicles is increasing because of environmental issues. For this reason, the importance and necessity of detecting defects on a CNG fuel tank has also come to the fore. The conventional AE method used for source location is highly affected by the wave speed on the structure, and this creates problems in inspecting a composite CNG fuel tank. Because the speed and dispersion characteristics of the wave are different according to direction of structure and laminated layers. In this study, both the conventional AE method and the energy based contour map method were used for source location. This new method based on pre-acquired D/B was used for overcoming the limitation of damage localization in a composite CNG fuel tank specimen which consists of a steel liner cylinder overwrapped by GFRP. From the experimental results, it is observed that the damage localization is determined with a small error at all tested points by using the energy based contour map method, while there were a number of mis-locations or large errors at many tested points by using the conventional AE method. Therefore, the energy based contour map method used in this work is more suitable technology for inspecting composite structures.