• Journal of the Korean Institute of Gas
• /
• v.3 no.1
• /
• pp.14-20
• /
• 1999

This study describes the results of Coefficient of Performance(COP) analysis by cycle simulation for two types of absorption-compression hybrid cycle using the Water/Lithium Bromide solution pair. These types are basic hybrid systems introducing a mechanical compression process into the refrigerant vapor phase of the single effect absorption cycle. In absorption-compression hybrid cycles, coefficient of performance is improved compared with absorption cycle. Hybrid cycle Type 2 is considered as a key technology to support energy utilization system, given its capability of utilizing waste heat to drive system with a high level of efficiency.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.8
• /
• pp.31-37
• /
• 2011

In order to evaluate the effect of matric suction on the strength and deformation characteristics, the unsaturated unconfined compression test is performed for the statical1y compacted silty sand. Specimens used were made under conditions with various initial degrees of saturation. The initial matric suction, matric suction at the peak shear strength and the volumetric deformation during the shear process were measured. From these results, it was found that the initial degree of saturation exerts the influence on the behaviors of suction, peak shear strength and the volumetric deformation. Furthermore, the suction stress($P_s$) which means the apparent cohesion due to matric suction in the unsaturated shear strength could be derived.

• Composites Research
• /
• v.22 no.6
• /
• pp.32-38
• /
• 2009

In this study, the energy absorption capabilities and failure modes of four different kinds of circular tubes made of carbon, Kevlar and carbon-Kevlar hybrid composites with epoxy resin have been evaluated. In order to achieve these goals, these tubes were fabricated with unidirectional prepregs and compressive tests were conducted for the tubes under 10mm/min loading speed. From the test results, carbon/epoxy tubes were collapsed by brittle fracturing mode and showed the best energy absorption capabilities, while Kevlar/epoxy tubes were crushed by local buckling mode and worst. The hybrid [$90_C/0_K$] tubes were failed in a local bucking mode and showed good post crushing integrity, whereas [$90_K/0_C$] tubes were failed in a lamina bending mode and bad post crushing integrity.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1701-1708
• /
• 2002

본 연구의 목적은 자외선 차단 가공 처리 및 자외선 조사처리에 의해 면직물의 역학적 특성 변화를 조사하고 가공제 처리조건에 따른 차이점을 분석하는 것이다. 시료로는 100% 면직물을, 자외선 흡수제로 2,2'-dihydroxy-4,4'-dimethoxy benzophenone을, 첨가제로 Triton X-100, polyethylene glycol 400, MgCl$_2$.6$H_2O$를 사용하였다. 자외선 흡수제 처리는 Atlas Launder-O-meter로 75$^{\circ}C$에서 60분간 흡진법으로 하였다. 미처리 시료 및 처리시료는 모두 xenon 램프에 80시간 동안 노출되었으며, 자외선 조사 전후 시료의 역학적 특성은 KES-F시스템을 사용하여 측정하였다. 본 연구의 결과는 다음과 같이 요약할 수 있다. 자외선 흡수제 처리는 처리 농도에 상관없이 면직물의 선형인장성(LT), 인장레질리언스(RT), 굽힘강성(B), 굽힘이력(2HB), 전단강성(G), 전단이력(2HG5), 표면마찰계수(MIU)등을 증가시켰으며 표면거칠기(SMD)는 감소시켰다. 압축특성은 처리농도의 영향을 받아서 고농도의 자외선 흡수제 처리는 압축특성을 감소시켰으며, 저농도의 처리는 압축특성을 증가시켰다. 자외 선 흡수제 처리는 처리농도에 상관없이 면직물의 fullness/softness를 유의하게 증가시키는 반면 stiffness, crispness및 anti-drape stiffness를 감소시켜서 가공포의 종합태(THV)는 가공 전에 비하여 저하하였다. 자외선 조사는 가공 전 면직물의 경우 B, 2HB, G, 2HG, 2HG5, LC를 감소시켰다. 자외선 조사는 처리농도와 상관없이 가공포의 WT, 굽힘특성 , 전단특성을 감소시켰으며, 저농도의 흡수제 처리포의 경우 SMD를 증가시켰으며, 고농도의 흡수제 처리포의 경우 SMD를 감소시켰다. 자외선 조사는 처리농도와 상관없이 가공포의fullness/softness, stiffness, anti-drape stiffness를 유의하게 감소시켜서 자외선 조사 전 보다 THV가 37% 저하하였고 미 가공포의 THV를 저하율보다는 저하가 낮았다. 자외선 흡수제 처리에 의해 면직물의 태는 가공 전보다 감소하지만, 자외선 흡수제 처리는 자외선 조사에 의한 태 감소율을 낮추는 데 유의 한 효과가 있다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.5
• /
• pp.91-100
• /
• 2008

A technique strengthened to the reinforced concrete members using the external post- tensioned method offers the advantages in speed and simplicity of installation over other, established, strengthening techniques. But this technique has many unreasonable facts. This paper are analyzed an unreasonable facts of the previous external post-tension technique. The purpose of this paper proposed Bow system as the new technique strengthened to the reinforced concrete members. The Bow system which is better technique than the previous technique was introduced with the experimental/analytical data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.3
• /
• pp.229-235
• /
• 2011

This research aims todevelopa compression/absorption hybrid heat pump system using an $NH_3/H_2O$ as working fluid.The heatpump cycle is based on a combination of compression and absorption cycles. The cycle consists of two-stage compressors, absorbers, a desorber, a desuperheater, solution heat exchangers, a solution pump, a rectifier, and a liquid/vapor separator. The compression/absorption hybrid heat pump was designed to produce hot water above $90^{\circ}C$ using high-temperature glide during a two-phase heat transfer. Distinct characteristics of the nonlinear temperature profile should be considered to maximize the performance of the absorber. In this study, the performance of the absorber was investigated depending on the capacity, shape, and arrangementof the plate heat exchangers with regard tothe concentration and distribution at the inlet of the absorber.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.6
• /
• pp.20-29
• /
• 2016

This study investigates the effect of the absorbent materials on the material properties(compressive strength and drying shrinkage) of natural hwangtoh mortar which is one of the traditional building material in Korea. The absorbent materials used are seaweed paste and Super-Absorbent Polymer(SAP). In addition to the absorbent materials, the initial sealed curing recommended by the standard specification of properties for Korean traditional building materials is also a main interest of this study. Based on the test results of 28 days compressive strength and converged drying shrinkage, it is confirmed that the initial sealed curing for 7 days is effective to reduce the drying shrinkage and to enhance the compressive strength. Thus, it is verified that the recommendation is reasonable and has positive effects on the properties of the mortar. Next, the test results show that the addition of absorbent materials into the mortar is also effective to the two properties depending on their absorption capacity. Thus, it is more effective to use SAP than the seaweed paste because of higher absorption capacity. However, both the initial sealed curing and keeping total water contents of the mortar are required to show this effectiveness. Lastly, the compressive strength is inversely proportional to the drying shrinkage. By using this relation, the reason of the increase of compressive strength due to the initial sealed curing or the addition of absorbent materials is quantitatively explained.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.193.2-193.2
• /
• 2012

달착륙선 등과 같은 특수 목적을 위해 제작된 우주용 착륙선에는 착륙 시 전달되는 충격하중이 탑재장비로 전달되지 못하도록 연착륙(soft-landing)을 위한 충격흡수 메커니즘이 구현되어 있어야 한다. 일반적으로 자동차 및 항공기에서는 실린더와 피스톤으로 구성된 유공압식 완충장치를 주로 사용하여, 피스톤 압축으로 실린더 내부 오일 또는 압축공기가 오리피스를 통하여 분출됨에 따라 유체마찰 에너지를 활용한 충격 흡수장치가 일반적이다. 그러나 이와 같은 지상 장비용 유공압식 충격흡수 메커니즘은 진공 및 무중력 우주 환경하에서 오리피스 기능 상실, 유압유 기화 현상 및 극저온/고온 환경에서의 성능저하 등의 문제점으로 인하여 우주용 착륙선 충격완충장치로 적용이 불가능하다. 따라서 기존의 우주용 착륙선의 대부분은 충격에너지를 기계적인 좌굴 소성 변형에너지로 변환하여 충격을 흡수할 수 있도록 알루미늄 허니콤을 주로 많이 사용하여 왔다. 본 연구에서는 진공 및 무중력 우주환경에서 착륙선 충격완충 장치로 적용이 가능하도록 실리콘 포옴과 스프링을 조합하여 구성하였으며, 충격완충 매체로 유압유 및 공압을 대체할 수 있도록 실리콘 포옴을 후방 사출 성형 방식으로 적용하여 오리피스를 통과한 실리콘 포옴의 변형에너지로 충격에너지를 흡수하게 함으로서 착륙 완충효율을 극대화 할 수 있도록 검토하였다.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.19-31
• /
• 2002

Crush energy characteristics of graphite/epoxy square tubes are experimentally studied. Effect of the ply orientation on the peak load and the average load is investigated by applying compressive load on the top of the composite square tubes under the stroke control with crosshead speed of 0.003mm/sec and 0.3mm/sec. in addition to the experimental survey, the finite element analysis is used to estimate the peak load of the composite square tubes with [0/90]₄ and [0/±45/90]₂. The first buckling mode of the tube is superimposed to the perfect geometry and the distributed compressive load is applied on the top of the tubes. The applied compressive load that make Tsai-Wu criteria equal to one is regarded as the peak load of the tubes. The experimental data shows that the square tube with [45/-45]₄ has the highest peak load and the square tube with [60/-60]₄ has the average sustained load. The measure peak load of the composite tubes with [0/90]₄ and [0/±45/90]₂agree well with the estimated peak load using the finite element analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1367-1373
• /
• 2011

This research concerns the development of a compression/absorption high-temperature hybrid heat pump that uses a natural refrigerant mixture. Heat pumps based on the compression/absorption cycle offer various advantages over conventional heat pumps based on the vapor compression cycle, such as large temperature glide, temperature lift, flexible operating range, and capacity control. In this study, a lab-scale prototype hybrid heat pump was constructed with a two-stage compressor, absorber, desorber, desuperheater, solution heat exchanger, solution pump, liquid/vapor separator, and rectifier as the main components. The hybrid heat pump system operated at 10-kW-class heating capacity producing hot water whose temperature was more than $90^{\circ}C$ when the heat source and sink temperatures were $50^{\circ}C$. Experiments with various $NH_3/H_2O$ mass fractions and compressor/pump circulation ratios were performed on the system. From the study, the system performance was optimized at a specific $NH_3$ concentration.