• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.820-823
• /
• 2002

MEMS structures Generally have been fabricated using surface-machining, but the interface failure between silicon substrate and evaporated thin film frequently takes place due to difference of linear coefficient of thermal expansion. Therefore this paper studied the effect of the residual stress caused by variable external loads. This study did not analyzed accurate quantity of the residual stress but trend for the effect of residual stress. Several specimens were fabricated using other material(Al, Au and Cu) and thermal load was applied. The residual stress was measured by nano-indentation using AFM. The results showed the existence of the residual stress due to thermal load. The indentation area of the thermal loaded thin film reduced about 3.5% comparing with the virgin thin film caused by residual stress. The finite element analysis results are similar to indentation test.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.40-40
• /
• 2003

최근 나노기술의 발달과 더불어 나노재료에 대한 특성평가 요구가 높아지고 있고, 따라서 나노스케일에서 재료의 기계적 거동을 분석할 수 있는 나노인덴테이션 기법이 심도있게 연구되고 있다. 본 연구에서는 나노인덴테이션, 주사탐침현미경(SPM), 투과전자현미경(TEM) 기법을 이용하여 여러가지 재료의 탄성 소성 변형 거동과 팝인/괍아웃 현상을 조사하고 해석하였다. 나노인덴테이션 기법으로는 50 마이크로뉴턴 (5 mg) 이하의 매우 작은 하중 하에서는 접촉 응력조건이라도 인장시험에서 관찰되는 영구변형이 제로인 완전탄성 변형 거동을 관찰할 수 있었다. 또한, 50-250 마이크로 뉴턴의 하중 범위에서 재료는 탄성변형 이후에 갑작스런 항복거동과 더불어 수십-수백 나노미터를 미끌어지듯 변형하는 팝인(pop-in), 또는 탈선(excursion) 현상을 관찰할 수 있었다. 이 현상은 하중을 가하는 동안에 여러 번 발생하였으며 재료의 표면상태와 전위밀도와 밀접한 상관관계를 보였다. 반복 압입 시험에서는 전형적인 가공경화 현상으로 항복점이 높아지고 새로운 항복점 이후에야 다시 팝인 발생함을 보였다. 한편, 하중을 가할 때 발생하는 팝인과는 달리 하중을 제거할 때 급격히 회복하는 팝아웃 현상 또한 관찰되었다.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.398-401
• /
• 2011

초음파의 응용분야에는 음파 성질을 이용한 정보 측정분야와 에너지를 이용한 용접 및 가공 등을 들수 있다. 초음파 용접의 경우 저항용접이나 용융 용접을 적용할 수 없는 재료의 접합에 이용되는데 이는 모재를 음극간에 놓고 압입하면서 초음파를 발신하여 그 진동을 이용하는 용접방법이다. 압전소자의 경우 피에조 물질을 사용하는데 일반적으로 $150^{\circ}C$이상에서 분자구조의 변형을 일으켜 제 역할을 못하게 된다. 본 연구에서는 압전소자와 공구혼의 온도를 최적으로 유지하기 위하여 추가적인 공기 유로와 방열핀을 설계하여 이것이 방열성능에 미치는 영향에 대해 고찰하였다.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.660-665
• /
• 2003

The true stress - true strain relation of SA508 steel was evaluated with analytical and experimental equation on the base of the indentation load-depth curve obtained from the modeling of ball indentation test. The evaluated relation between true stress and true strain is agreed well with that of SA508 teel defined in the modeling. The distribution of effective stress along the center axis of indentation depth was calculated with Tresca criteria in the modeling. The representative strain, which are defined in this study as the corresponding strains obtained from the maximum effective stress, have a linear relation with the true strain. The true stress - true strain relation of austenitic stainless steel was evaluated by the modeling of ball indentation test to verify the case of A508 steel.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.9
• /
• pp.47-54
• /
• 2003

In this study, to achieve the optimal conditions for mechanical hyper-fine pattern fabrication process, deformation behavior of the materials during indentation was studied with numerical method by ABAQUS S/W. Polymer (PMMA) and brittle materials (Si, Pyrex glass) were used as specimens, and forming conditions to reduce the elastic re cover and pile-up were proposed. The indenter was modeled a rigid surface. Minimum mesh sizes of specimens are 1 -l0nm. Comparison between the experimental data and numerical result demonstrated that the finite element approach is capable of reproducing the loading-unloading behavior of a nanoindentation test. The result of the investigation will be applied to the fabrication of the hyper-fine pattern.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.246-251
• /
• 2004

Nano-indentation is used for measuring mechanical properties of thin films such as elastic modulus and hardness. For ductile materials, pile-up around the indenter causes the calculation of inaccurate projected contact area. This phenomenon was found by measurement of indentation shape using an atomic force microscope. In present study finite element analysis of nano-indentation was performed to compensate the effects of pile-up on the contact area. The result of finite element analysis was compared with that of nano-indentation for a ductile material. The analysis has demonstrated that the true contact area is greater than that calculated by nano-indentation. It is verified that the consideration of the effects of pile-up in nanoindentation for ductile materials using the finite element method is reasonable.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.493-496
• /
• 2008

The residual stress generated in the boron steel blank formed via hot press forming process was predicted by JMatPro, a material property modeler, and Abaqus. The numerical predictions were compared by the experimental measurements obtained by the instrumented indentation. Both the predicted and measured principal stresses monitored at the outer surface of central bending position were qualitatively in good agreement. It was concluded that the residual stresses generated from hot forming process is not negligible as it has been generally assumed, although the spring back deformation is quite small. This should be specially considered from the part design stage since the tensile nature of the residual stress exhibited on the surface may lead to the stress corrosion cracking.

• Tribology and Lubricants
• /
• v.30 no.4
• /
• pp.199-204
• /
• 2014

Various heat-treated and surface coating methods are used to mitigate abrasion in sliding machine parts. The most cost effective of these methods involves hard coatings such as diamond-like carbon (DLC). DLC has various advantages, including a high level of hardness, low coefficient of friction, and low wear rate. In practice, a supporting layer is generally inserted between the DLC layer and the steel substrate to improve the load carrying capacity. In this study, an indentation and sliding contact problem involving a small, hard, spherical particle and a DLC-coated steel surface is modeled and analyzed using a nonlinear finite element code, MARC, to investigate the influence of the supporting layer thickness on the coating characteristics and the related coating failure mechanisms. The results show that the amount of plastic deformation and the maximum principal stress decrease with an increase in the supporting layer thickness. However, the probability of the high tensile stress within the coating layer causing a crack is greatly increased. Therefore, in the case of DLC coating with a supporting layer, fatigue wear can be another important cause of coating layer failure, together with the generally well-known abrasive wear.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.1095-1101
• /
• 2012

A process heat exchanger (PHE) in a nuclear hydrogen system is a key component that transfers the large amount of heat generated in a very high temperature reactor (VHTR) to a chemical reaction that yields a large quantity of hydrogen. A performance test on a small-scale and a medium-scale PHE prototype made of Hastelloy$^{(R)}$-X is being conducted on in a small-scale nitrogen gas loop at the Korea Atomic Energy Research Institute. Previous research on the macroscopic high-temperature structural analysis of PHE prototypes had been performed using base material properties owing to a lack of weld material properties. In this study, macroscopic high-temperature structural analyses considering the weld material properties were performed and the results were compared with those of a previous study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1415-1421
• /
• 2013

Recently, to resolve problems regarding legal liability for accidents and disasters, various simulation techniques such as F.E.M. and F.V.M. have been used in the field of forensic engineering. In this study, we performed mechanical structure analysis using ADINA to investigate the cause of bridge collapse accidents. Such accidents occurred owing to modified and missing processes in comparison with the original design while filling with concrete. Modified and missing processes cause buckling of the upper plate and twisting of the main girder. Through this study, we determine the exact cause of bridge collapse by comparing the evaluation of the structure stability of the original design with the evaluation of the structure stability of the modified and missing process using ADINA structure analysis. Hence, this result indicates that buckling prediction through FEA is the most effective method.