• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1B
• /
• pp.83-90
• /
• 2009

This study describes the characteristics of distribution of lift-force acting under pier deck through physical experiment. The shape of peak wave pressure was sharp when compressed air existed but was not sharp without that. Values of lift-force was different between edge point and center point in the same block. Distribution of lift-force was expressed differently owing to dimensionless of deck length (l/L), wave steepness (H/L), clearance height per wave height (D/H). The dimensionless factor of D/H affected on the lift-force the clearance between still water surface and decks. This decided the maximum of lift-force. In the case of the same values of D/H, the lift-force are changed by the wave steepness (H/L). Because (D/H) become smaller as the wave steepness (H/L) is increased the height of decks must be decided with the condition which don't have the clearance with $D_{max}$ for the stable design of deck of pier. Effect of reducing lift force was greater in the on-shore than the off-shore according to compressed air existence. This researches points out that design of deck should retain compressed air in order to reduce wave lift force.

• Journal of Biomedical Engineering Research
• /
• v.20 no.5
• /
• pp.587-592
• /
• 1999

압력측정시스템은 입각기동안 동적압력분포를 성공적으로 측정할 수 있으나 하중수용기-중간입각기, 말기입각기-전유각기의 전환기들에 대해서는 운동분석시스템을 사용하지않고는 정확한 정의가 불가능하다. 따라서 저자들은 수평자유보행 시 압력중심의 이동을 이해하기 위해서 정상적인 발을 가진 20-30대 성인남자 78명을 대상으로 동작분석과발바닥 압력측정을 동시에 수행하였다. 결과로 하중반응기-중간입각기 전환시기의 발바닥 압력중심점은 후족부와 중족부의 경계선에서 앞쪽으로 1.9$\pm$1.5frame(32$\pm$24msec)에 위치하였으며 말기입각기-전유각기 전환시기에는 중족골두 최대 압력점의 앞쪽으로 2.3$\pm$2.0 frame(38$\pm$33msec)에 위치하였다. 정상수평보행에 있어서 최초접지 순간 압력중심은 전방으로 빠르게 이동하다가 바로 급속히 감소하여 하중반응기-중간입각기의 전환시기에는 작은 속도로 이동하였다. 압력중심의 이동속도는 그 후 다시 서서히 증가하다가 전체 보행주기의 25% 전후에서 서서히 감소하여 비교적 일정하다가 말기입각기-전유각기의 전환시점에서 다시 급격한 증가를 보였다. 족부질환과 보행특성을 판단하는데 있어서 압력중심의 이동궤적은 매우 유용한 인자가 될 것으로 기대된다. 본 연구를 통해서 압력측정시스템만으로는 정의할 수 없었던 두 전환기인 하중반응기-중간입각기, 말기입각기-전유각기를 결정할 수있게 되었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.339-342
• /
• 2008

The PSP(Pressure Sensitive Paint) is a technique to measure continuous pressure distribution on medel surface by oxygen quenching. The objective of this study is to apply PSP which is measured pressure for analyzing that air-fuel mixing characteristics in SCRamjet combustor. Experimentation is performed at freestream Mach number of 2.5 and used fuel jet injection. The result shows that growing air-fuel mixed proportions by increasing in cavity size. Also, PSP results compared with conventional pressure tap and CFD. They are coincided with qualitative and the inclination.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.317-321
• /
• 2007

PSP (Pressure Sensitive Paint) technique can measure continuous pressure field by analyzing the oxygen quantity using optical method. The surface pressure of down stream after the sonic jet that injected transversely into the supersonic freestream was measured by PSP technique. Moreover the effect of various rectangular shaped cavities in front of the jet was measured by PSP technique. A comparison of the PSP results with conventional pressure tap and CFD indicates good agreement. The result shows that the cavity affects the pressure distribution in the rear of the jet injection.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1994.11a
• /
• pp.1-5
• /
• 1994

우주공간의 압력은 일반적으로 지구로부터의 고도와 대수 관계에 있으며 위성이 비행하는 궤도는 $10^{-6}$-$10^{-11}$torr의 초진공 상태에 가깝고 고도 수십 km까지는 희박기체의 압력으로 볼 수 있으나 그 이상의 고도에서는 기체 분자가 거의 이온이 되어 대단히 고속의 이온 흐름 상태를 유지하고 있다. 우주용 추진기관 개발에 있어서 이와 같은 초고진공에 해당하는 압력을 구현하지 않으면 않되는 시험 이외에도 비교적 고도가 낮은 공간의 SIMULATION에도 중요한 분야이다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.56-56
• /
• 2003

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.4 no.2
• /
• pp.7-12
• /
• 2008

The purpose of this study is to present a methodology to estimate the capacity of the pressure relief valve which prevents overpressure of the pressure vessel in a cold state. In this methodology, the transient behavior of the flow rate through the pressure relief valve and the pressure inside the pressure vessel are considered. The result of this study shows the followings; The more the relief valve capacity is considered in excess, the more the initial relief flow rate and the initial pressure inside the pressure vessel are high and low respectively. When the relief valve capacity is determined properly, the pressure inside the pressure vessel maintains almost the same value, so the ASME code requirement will be met.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.476-482
• /
• 2010

알루미늄은 많은 이점에도 불구하고 표면의 높은 용융점을 가지는 산화 피막 효과로 인해 원활하게 점화와 연소 반응이 일어나지 못하는 단점이 있다. 그런데 산화피막을 제거하는 방법은 매우 복잡하며 용이하지 않으므로 본 연구에서는 연소율은 압력에 비례한다는 원리를 이용하여 접근하였다. 연소 속도의 압력에 따른 민감도를 알기 위해 압력 용기를 설계하였고 아르곤 가스를 이용하여 80nm의 알루미늄 분말과 산화제인 증류수의 혼합물을 3, 5, 10 기압의 압력 조건에 따른 연소속도의 변화를 측정하고 해외의 연구와 비교 분석하였다.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.18-23
• /
• 1989

본 기고에서는 필자의 경험을 바탕으로 콘덴서 마이크로폰(condenser microphone)을 압력측정 프로우브에 직접 연결하여 압력변동성분을 측정하는 방법을 소개하고, 이 방법의 적용예와 문제점을 검토하고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.268-276
• /
• 2017

Developing a model was carried out to predict the characteristic of a pressure vessel from which the gas was vented through an orifice. An experimental test was conducted on a pressure vessel applicable to a propulsion system so that representative pressure and temperature were measured. Simulations were conducted with models using assumptions considering heat transfer inside the vessel, and the results were compared to those from the experiment. As a result, it was found out that a proposed heat transfer model was proper to predict pressure and temperature of the vented gas comparable to the measured data.