• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.255-260
• /
• 1998

Fabrication condition and magnetic properties of ultrathin Co-based amorphous alloy have been investigated. When the ejection gas pressure was lower than 0.05 kgf/$\textrm{cm}^2$ at the roll speed of 55 m/s, ultrathin ribbons with the thickness less than 10 ${\mu}{\textrm}{m}$ were successfully obtained. The ribbon thickness decreased linearly with the decrease in ejection pressure. Moreover the significant decrease in ribbon width was accompanied with the decrease of thickness in the range of ejection pressure to form an ultrathin ribbon. This behavior was attributed to the decrease of effective ejection pressure in the both end-sides of rectangular nozzle due to the larger friction between molten metal and nozzle wall. The effective permeability at low frequency (1 kHz) decreased largely with the decrease in ribbon thickness, while the coercive force increased with the thickness decrease. It was considered that these behaviors were due to the enhancement of surface effect leading to the suppression of wall motion. However effective permeability at high frequency (1 MHz) increased with the decrease in ribbon thickness, and this was ascribed to the easier magnetization rotation owing to the reduction of eddy current.

• Journal of Life Science
• /
• v.17 no.11
• /
• pp.1477-1481
• /
• 2007

The mating systems of natural populations of Vicia tetrasperm in Korea were determined using allozyme analysis. The result suggests that V. tetrasperm is low rates of outcrossing or mix-mating outcrossing (self-fertilization, s < 0.5). At the population levels, the values of inbreeding coefficient of ten populations in Korea varied from 0.131 to 0.176, giving an average 0.154. For ten natural populations, multi-locus estimates of outcrossing (tm) was 0.333 across fifteen polymorphic loci, with individual population values ranging from 0.269 to 0.423. The differences between the tm and ts values were not close to zero (tm - ts > 0.154), indicating that biparental inbreeding was significant in the loci. The reason for relatively low outcrossing rates of some populations could be attributed to extensive consanguineous mating and isolation of flowering mature plants. Although heterozygote excess was observed in one natural population, most populations exhibited varying degrees of inbreeding and heterozygotes deficit. Thus, selection against homozygotes operated in the progeny populations throughout the life cycle.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.222-228
• /
• 2018

Benzene is one of the most widely used basic materials in the petrochemical industry. Generally, benzene exists as a mixture with alcohols rather than as a pure substance. Further, the alcohols-added mixtures usually exhibit an azeotropic composition. In this context, knowledge of the phase equilibrium behavior of the mixture is essential for its separation and purification. In this study, the vapor-liquid equilibrium data were measured in favor of a recirculating VLE apparatus under constant pressure for the 1 - propanol / benzene system. The measured vapor - liquid equilibrium data were also correlated by using the UNIQUAC and WILSON models and the thermodynamic consistency test based on the Gibbs/Duhem equation was followed. The results of the phase equilibrium experiment revealed RMSEs (Root Mean Square Error) and AADs (Average Absolute Deviation) of less than 0.05 for both models, indicating a good agreement between the experimental value and the calculated value. The results of the thermodynamic consistency test also confirmed through the residual term within ${\pm}0.2$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.165-170
• /
• 2015

The topic of this paper is the advanced absolute altitude determination for 3-D positioning using barometric altimeter and the reference station. Barometric altimeter does not provide absolute altitude because atmosphere pressure always varies over the time and geographical location. Also, since Global Navigation Satellites system such as GPS, GLONASS has geometric error, the altitude information is not available. It is the reason why we suggested the new method to improve the altitude accuracy. This paper shows 3-D positioning algorithm using absolute altitude determination method and evaluates the algorithm by real field tests. We used an accurate altitude from RTK system in Seoul as a reference data and acquired the differential value of pressure data between a reference station and a mobile station equipped in low cost barometric altimeter. In addition, the performance and advantage of the proposed method was evaluated by 3-D experiment analysis of PNS and CNS. We expect that the proposed method can expand 2-D positioning system 3-D position determination system simply and this 3-D position determination technique can be very useful for the workers in the field of fire-fighting and construction.

• Journal of the Korean Institute of Gas
• /
• v.17 no.4
• /
• pp.1-8
• /
• 2013

The aim of this study is to assess thermal hazards of polystyrene polymerization process by bulk polymerization with accelerating rate calorimeter(ARC) and Multimax reactor system(MM). From this study, we found out that the polymerization process should be operated at reaction temperature of $120^{\circ}C{\sim}130^{\circ}C$. At reaction temperature over $130^{\circ}C$, there was a runaway reaction hazard due to the temperature control failure following a viscosity increase of reaction products. With a cooling failure of a reactor in the early stage of process operation at the reaction temperature ($120^{\circ}C{\sim}130^{\circ}C$), there was a high thermal hazard of burst of a reactor's rupture disk or explosion of a reactor caused by the rapid rise of temperature and pressure to $340^{\circ}C$, 5.3 bar respectively within 30 - 50 minutes.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.354-359
• /
• 2013

일반적으로 건축물의 설계시 풍동 실험을 통한 풍환경의 평가를 수행하고 있으며, 이는 환경 영향 평가법에서 정한 건축 사업 시행 시 수반되어야 할 자연환경, 생활환경 그리고 사회경제환경의 영향 평가의 일환으로 실시되고 있다. 그러나, 풍동 실험의 경우 여러 가지 현실적 제약조건으로 설계와 실험의 피드백 (Feedback)이 원활하지 못하며, 특히 대상 건축물이 공장과 같이 대기 오염원이 되는 경우 실험은 더욱 어려운 형편이다. 이에 대한 보완책으로 전산 유체 역학을 이용한 건축물의 풍압 해석에 의한 풍하중 추정이나 인접 지형-지물의 영향을 고려한 건축물 주위의 풍환경 평가가 있다. 전산 모사에 의해 풍동 실험의 미비점을 보완하고, 보다 상세한 정보를 확보함으로써 건축물의 구조적 안전성의 증대와 환경 피해 감소를 기할 수 있다. 그러나 복잡한 지형-지물이나 건축물 주위의 풍환경에 대한 전산 모사는 주로 두 가지의 기술적 어려움을 수반하게 되다. 그 중 하나는 고정 경계면을 이루는 형상의 복잡성으로 인해 기존에 많이 이용하고 있는 Body-fitted 격자계를 이용하는 경우, 격자 생성 과정이 매우 복잡하고 어려울 뿐 만 아니라 생성된 격자가 주로 비정렬 (unstructured) 특성을 갖게 되어 수치해석 과정의 효율을 저하시키는 요인이 되며, 격자의 형상도 수치해석의 수렴성을 저하시키는 예가 많다. 다른 어려움으로 풍환경은 전형적인 난류 유동장으로서 난류의 전산 해석은 아직도 해결하지 못한 부분이 많다는 점이다. 이에 본 논문에서는 복잡한 지형-지물이나 건축물의 풍하중과 풍환경의 전산 모사 기술 확보를 위하여 수행중인 연구의 일환으로 물체 형상의 기하학적 복잡성의 극복을 위한 가상경계법 (Immersed Boundary Method)과 난류 유동장의 물리적 엄밀성을 높이기 위한 다와동 모사 (Large Eddy Simulation)을 이용한 물체 형상과 무관한 유동장 해석 기술 개발에 대하여 다루고자 한다. 먼저 최근에 유동 해석에 이용되는 방법인 가상경계법(IBM)은 물체를 포함한 전체 전산 영역을 직교 좌표계에 의해 이산화하고, 유동장내 존재하는 물체의 표면에서의 점착 조건을 만족시키기 위하여 지배 방정식에 적절한 외력을 추가로 고려하는 방법이다. 본 연구에서는 가상경계법을 이용하여 경계층에 위치한 건물 형상의 각진 물체 주위 사이에 형성되는 공동 내부의 비정상 유속 및 압력에 대한 전산 해석을 수행하고, 풍상측 전면에 형성되는 경계층에 의한 영향을 분석하였다.

• Applied Biological Chemistry
• /
• v.40 no.5
• /
• pp.442-446
• /
• 1997

A new analytical method was developed by HPLC after supercritical fluid extraction and fluorogenic derivatization for the determination of quinclorac (3,7-dichloro-8-quinoline carboxylic acid) in soil. The graminicide quinclorac was extracted from soil by supercritical fluid extraction. Supercritical carbon dioxide at 7000 psi $(80^{\circ}C)$ modified with 30% of methanol extracted quinclorac from soil samples at the level of $0.1ng\;g^{-1}$ with 96% recovery. Extracted quinclorac was determined by HPLC as a fluorescent derivative. Derivatization was made with 4-bromomethyl-7-methoxycoumarin (4-Br-Mmc) using 18-crown-6-ether as a catalyst. The conversion was completed within 30 min and the limit of detection was 0.5 ppb to prove that the procedure could be used in the residue analysis of the pesticides containing carboxylic acid group.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.470-471
• /
• 2007

환경친화적 가스절연기기의 개발을 위해 $SF_6/N_2$와 완충기체와의 혼합가스에 관한 연구가 주목받고 있다. 본 논문에서는 GIS 설계에 있어 기초가 되는 준평등전계 하에서의 가스 절연특성을 검토하기 위하여 순 SF6, N2, CO2 이들이 혼합된 2종 및 3종 혼합가스에 대해 가스압력 0.6MPa 이하에서 상용교류전압을 인가하여 실험에 의해 그 부분방전특성과 절연특성을 조사하였다. 특히 실용 전력기기의 경우 금속이물질 등의 혼입에 의해 기기 내에서 불평동전계가 형성되어 부분방전을 거쳐 절연파괴에 이르는 가능성이 있으므로 본 연구에서는 불평등전계하의 절연특성을 검토하였다. 실험 결과 SF6/N2 2종 혼합 가스에 비하여 SF6/N2/CO2 3종 혼합 가스의 교류 절연 특성이 향상됨을 확인하였으며 이상의 결과로부터 교류 절연 파괴 특성만을 고려하였을 경우 SF6/N2/CO2 3종 혼합 가스가 SF6 대체 혼합가스로써 타당성을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.1
• /
• pp.65-74
• /
• 2004

The heat transfer coefficient and pressure drop of $CO_2$(R-744) during gas cooling Process of carbon dioxide in a horizontal tube were investigated experimentally and theoretically. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop consist of a receiver. a variable-speed pump. a mass flowmeter, an evaporator. and a gas cooler(test section). The main components of the water loop consist of a variable-speed Pump. an constant temperature bath. and a flowmeter. The gas cooler is a counterflow heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus The test section consists of smooth, horizontal stainless steel tube of 9.53 mm outer diameter and 7.75 mm inner diameter. The length of test section is 6 m. The refrigerant mass fluxes were 200 ~ 300 kg/($m^2{\cdot}s$) and the inlet pressure of the gas cooler varied from 7.5 MPa to 8.5 MPa. The main results were summarized as follows : The predicted correlation can evaluated the R-744 exit temperature from the gas cooler within ${\pm}10%$ for most of the experimental data, given only the inlet conditions. The predicted gas cooley capacity using log mean temperature difference showed relatively food agreement with gas cooler capacity within ${\pm}5%$. The pressure drop predicted by Blasius estimated the pressure drop on the $CO_2$ side within ${\pm}4.3%$. The predicted heat transfer coefficients using Gnielinski's correlation evaluated the heat transfer coefficients on the $CO_2$ side well within the range of experimental error. The predicted heat transfer coefficients using Gao and Honda's correlation estimated the heat transfer coefficients on the coolant side well within ${\pm}10\;%$. Therefore. The predicted equation's usefulness is demonstrated by analyzing data obtained in experiments.

• Korean journal of food and cookery science
• /
• v.4 no.2
• /
• pp.51-56
• /
• 1988

The sensory and instrumental characteristics of warm and cool cooked rices with pressure and electric cookers were examined. The types of rice varieties tested were Choucheong (traditional rice variety) Samgang and Seogwang (high-yielding rice varietis) The result of sensor evaluation revealed more significant differences in most of appearance, texture characteristics than flavour. The difference of sensory characteristics according to the types of cookers and the warm or cool cooked rices was greatest in Seogwang among three varieties. The instrumental measurement of cooked rices using instron showed that the difference between types of varieties and cookers was more clearly in cool cooked rices than warm ones. Especially hardness in instrumental characteristics revealed highly signficant difference. With regard to the correlation between instrumental and sensory characteristics, hardness had a significantly high correlation with texture while others had low ones.