• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.46-46
• /
• 1999

터보분자펌프(turbomolecular pump, TMP)는 각종 연구장비, 반도체 제조장치, 가속기, 핵융합 실험 장치 등 여러 분야에서 가장 널리 쓰이는 고진공 펌프로서 자리잡고 있다. 이런 TMP의 광범위한 사용에도 불구하고 성능평가에 관한 통일된 규격이 마련되어 있지 않다. 국제 규격협회(ISO)의 터보분자펌프 성능평가방법 시안을 토대로 제정중인 KS 규격은 아직 실험적인 근거를 자체적으로 가지고 있지 못하므로 앞으로 각 항목들에 대한 많은 실험이 수행되어야 한다. TMP의 성능을 나타내 주는 항목들 중 배기속도(pumping speed)와 압축비(compression ratio)는 가장 중요한 것들로서 다른 고진공 펌프 및 TMP 상호간의 성능을 비교할 수 있는 기본 항목이라 할 수 있다. 본 실험에서는 종래의 단순 TMP와 큰 기체유량에서도 안정된 배기속도를 유지하는 복합터보분자펌프(compound molecular pump, CMP)의 배기속도와 압축비 및 임계배압(critical backing pressure)을 KS 규격안대로 시험 평가하여 안의 평가방법과 기준의 타당성을 검토하고, 두 가지 다른 방식의 펌프에 적용할 수 있는지를 검토하였다. TMP 및 CMP 흡기구에 표준용기를 부착하고 수소 및 질소 기체를 사용하여 흡기구 압력을 변화시키면서 배기속도 및 압축비를 측정하고 배기구 압력을 변호시키면서 최대압축비 및 임계배압을 측정하였다. 흡기구의 압력측정에는 인출형 전리진공계(EG)를 사용하였고, 배기구의 압력측정은 전기용량의 격막진공계(CDG)와 피라니 진공계로 측정하였다. 진공계는 모두 회전식 점성진공계(SRG)로 교정한 후 사용하였다.

• Korean Journal of Materials Research
• /
• v.6 no.10
• /
• pp.986-990
• /
• 1996

본 논문에서는 정속마찰 시험기를 사용하여 공기중에서 핏치/CVI계와 페놀/CVI계 낱소/탄소 복합재료의 마찰특성을 평가하고 상호 비교하였다. 운용조건(마찰거리, 마찰속도, 마찰압력)에 관계없이 페놀/CVI계의 평균 마찰계수가 핏치/CVI계 보다 높은 값을 나타내었다. 마찰거리가 4Km이하 일때는 평균 마찰계수가 불안정한 경향을 나타내고 그 이후에서는 안정한 평균 마찰계수 값을 갖는다. 또한 마찰속도와 마찰압력이 증가할수록 평균 마찰계수는 감소하는 경향을 나타내며, 페놀/CVI계의 평균 마찰계수가 핏치/CVI계 보다 높고 마찰면 온도 상승률과 최대 마찰면 온도도 높다. 마찰계수는 마찰면 온도의 영향을 받으며, 마찰속도와 3kg/$\textrm{cm}^2$이하에서 마찰압력이 커질수록 최대 마찰계수를 갖는 마찰면 온도는 높아진다.

• Journal of Energy Engineering
• /
• v.10 no.4
• /
• pp.335-341
• /
• 2001

Pressure pulsations generated by the blade-tongue interaction induce vibration of the piping systems and the structure connected to pumps, resulting in the severe noise and fatigue fracture. Experiments were made on the natural frequencies of liquid columns in piping systems with a single suction, single stage, centrifugal volute pump. Experimental results show that the natural frequencies of the liquid columns in the pump piping systems depend on the dimensions of the pipes and the impeller shapes, and are not affected substantially by the rate of discharge and the rotating speed of the pump.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.1
• /
• pp.135-143
• /
• 1990

Based on the mechanism of flat jack used to measure stresses in rocks, a prerssure gauge was developed to measure vertical stresses acting on the rigid boundary in a soil mass. This paper describes the mechanism of the newly built pressure gauge, the process of calibrating the response of this gauge, and its use to centrifugal model tests. By installing this gauge in centrifugal model experiments of reinforced earth retaining walls, vertical stress distribution at the rigid boundary of model wall was obtained and compared with theoretical prediction of trapezoidal vertical stress distribution.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.74-83
• /
• 2011

For launcher applications, different from other applications, very high flow rate is required which can lead to supply pressure drop against required setting pressure. The supply pressure decrease is closely related to regulator characteristics. In this paper, supply pressure offset is investigated considering regulators as kinds of control systems. Pressure offset of self-operated regulator is analyzed with sensitive parameter defined as the ratio of valve travel to pressure offset. It is shown that pressure offset of self-operating regulator can be improved by incorporating proportional and integral controls and they can be materialized with pilot regulator systems.

• The Journal of the Korea Contents Association
• /
• v.14 no.9
• /
• pp.120-130
• /
• 2014

The purpose of this study was to evaluate the effects of line dance activity on the balance factors during static standing to reveal the exercise intervention for fall prevention. A 15-week line dance programme was applied to 16 elderly females who aged more than 65 years in the community. Balance ability during static standing was evaluated by the range of center of pressure(cop), the velocity of cop, and sway area that calculated on the basis of ground reaction force data, forces, and moments. The range and velocity of cop in the anterio-posterior were significantly reduced after line dance(p<.01, p<.05, respectively), but change in those of cop in the medio-lateral was not found. It was demonstrated that 16-week line dance activities allow more effective in anterio-posterior stability and sway area of static standing. It was suggested that the effect of fall prevention exercise should be studied more associate with fall from vestibular and sensory system as future study.

• Journal of Korea Water Resources Association
• /
• v.42 no.7
• /
• pp.537-546
• /
• 2009

Determination of optimal pressure monitoring location is essential to manage water distribution system efficiently and safely. In this study, entropy theory is applied to overcome defects of previous researches about determining the optimal sensor location. The previous studies required the calibration using historical data, therefore, it was difficult to apply the proposed method in the place where the enough data were not available. Also, most researches have focused on the locations to minimize cost and maximize accuracy of the model, which is not appropriate for the purpose of maintenance of the water distribution system. The proposed method in this study quantify the entropy which is defined as the amount of information calculated from the pressure change due to the variation of discharge. When abnormal condition is occurred in a node, the effect on the entire network is presented by the entropy, and the emitter is used to reproduce actual pressure change pattern in EPANET. The optimal location to install pressure sensors in water distribution system is the nodes having the maximum information from other nodes. The looped and branched networks are evaluated using the proposed model. As a result, entropy theory provides general guideline to select the locations to install pressure sensors and the results can be used to help decision makers.

• KSBB Journal
• /
• v.11 no.1
• /
• pp.71-76
• /
• 1996

Studies were carried out to examine some factors affecting the supercritical carbon dioxide extraction of taxol from the bark of Taxus cuspidata using a continuous packed bed extractor. The factors investigated in this study were pressure, temperature, volume of carbon dioxide, and co-solvent. It was found out that the amount of taxol extracted was not significantly affected by the operating pressure in the absence of a co-solvent although it increased by about 20% at 5500 psig. With $24\ell$ of carbon dioxide the saturated amount of taxol was extracted at 318K and 5500psig. Methanol was found to be the most effective co-solvent in terms of amount of taxol extracted among six different co-solvents used. When methanol was used as a co-solvent the effect of operating pressure became significant; approximately 50% increase in the amount of taxol extracted was observed at 3000 psig as compared to at 2500 or 3500psig. The optimum methanol concentration in supercritical fluid was 13% (w/w)at 308K, 3000psig.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.5
• /
• pp.685-691
• /
• 2013

A load-cell-type anemovane operates based on wind vector properties. The developed load-cell-type anemovane is of a fixed type in which the wing does not rotate, unlike in the case of existing anemovanes. The load-cell-type anemovane is required to accurately derive the correlation between the load ratio and the wind direction in order to develop a qualified product. This is because the load ratio repeats every $90^{\circ}$ owing to the use of four load cells, and its value varies nonlinearly according to the wind direction. In this study, we compared analytical results with experimental results. Fluid analysis was carried out using ANSYS CFX. Furthermore, the prototype was tested using a self-manufactured wind tunnel. The wind direction was selected as the design variable. 13 selected wind direction conditions ranging from $0^{\circ}$ to $90^{\circ}$ with an interval of $7.5^{\circ}$ for analysis were defined. Furthermore, 10 wind direction conditions with an interval of $10^{\circ}$ for the experiment were defined. We derived the relations between the pressure ratio and the wind direction through the experiment and fluid analysis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.3
• /
• pp.258-263
• /
• 2012

In this paper the Chemical Propulsion Subsystem of COMS is briefly explained and some telemetries acquired by a series operations of CPS during the Launch and Early Operation Phase of COMS are presented. The pressure and temperature of pressurant tank telemetries are compared with the results of the developed computer program. The changes in pressure are due to the two major phases. The first one is the initialization phases of CPS composed of the venting phase to vent the helium gas in the pipe network from the downstream of the propellant tanks to the thrusters for safety, the priming phase to fill the vented pipe network with oxidizer and fuel respectively and then the pressurization phase to pressurize the ullage of propellant tank to regulated pressure. And the other is the apogee engine firings in which COMS CPS is in the orbit raising phase to use helium as a pressurant to keep the pressure of propellant tank as the liquid apogee engine get fired until COMS reached to the target orbit. This program can be applicable to prepare basis design data of the next Geostationary Satellite CPS.