• Journal of Sericultural and Entomological Science
• /
• v.16 no.2
• /
• pp.77-98
• /
• 1974

This study was carried out ill an attempt to investigate the properties and activities of sericin obtained from silk cocoon shells in silk reeling water through various instrumental analyses. In addition, the effects of the characteristics in sericin solubility on the reeling process and silk qualities were also studied on the basis of tile above conditions. The results obtained are as follows： I. The sericin properties and activities through various analytical instruments. 1. The water solubility of each amino acid such as serine, glycine. glutamic and aspartic acids against the pH modified water by using automatic amino acid analyzer, showed the lowest solubility at PH 5, but it increased according to drifting toward the alkalinity. 2. When the obtained sericin particles by water pH variation were observed with the electronic microscope, it was found for the sericin Particles to expand in the alkaline regions. 3. The IR spectrum results showed the differences among the pH modified sericin solutions at the range of 2,100cm-1 and 1.890cm-1 of wave number. 4. The existence of sericin with in silk fabrics made differences in the X-ray interference intencity, that is, the non-degummed fabrics had the interference peak at 2$\theta$=14$^{\circ}$, 17$^{\circ}$, 24$^{\circ}$, and the degummed ones had it at 2$\theta$=17$^{\circ}$, 18$^{\circ}$, 20$^{\circ}$, 23$^{\circ}$, 26$^{\circ}$. II. The results of sericin solubility for silk reeling process. 1. The sericin solubility and swelling had a tendency to increase up with high M-alkalinity and pH value of water. But in case of acidity. water hardness and concentration of ethylene glycol were high, the sericin solubility and swelling were decreased. 2. With the filature experiments, the best conditions of filature orator are summarized as fellows ; a. pH; 6.9${\pm}$0.2 d. acidity; below10ppm b. total hardness; 55：5ppm e. Fe ion; none c. M-alkalinity; 40${\pm}$10ppm

• Journal of the Korea Concrete Institute
• /
• v.29 no.4
• /
• pp.415-424
• /
• 2017

The purpose of this study is to investigate the effect of sulfate (${SO_4}^{2-}$) and magnesium ($Mg^{2+}$) ions on sulfate resistance of Alkali-activated materials using Fly ash and Ground granulated blast furnace slag (GGBFS). In this research, 30%, 50% and 100% of GGBFS was replaced by sodium silicate modules ($Ms(SiO_2/Na_2O)$, molar ratio, 1.0, 1.5 and 2.0). In order to investigate the effects of $Mg^{2+}$ and ${SO_4}^{2-}$, compression strength, weight change, lengh expansion of the samples were measured in 10% sodium sulfate ($Na_2SO_4$), 10%, 5% and 2.5% magnesium sulfate ($MgSO_4$), 10% magnesium nitrate ($Mg(NO_3)_2$), 10% [magnesium chloride ($MgCl_2$) + sodium sulfate ($Na_2SO_4$)] and 10% [magnesium nitrate $(Mg(NO_3)_2$ + sodium sulfate ($Na_2SO_4$)] solution, respectively and X-ray diffraction analysis was conducted after each experiment. As a result, when $Mg^{2+}$ and ${SO_4}^{2-}$ coexist, degradation of compressive strength and expansion of the sample were caused by sulfate erosion. It was found that the reaction of $Mg^{2+}$ with Calcium Silicate Hydrate (C-S-H) occurred and $Ca^{2+}$ was produced. Then the Gypsum ($CaSO_4{\cdot}2H_2O$) was formed due to reaction between $Ca^{2+}$ and ${SO_4}^{2-}$, and also Magnesium hydroxide ($Mg(OH)_2$, Brucite) was produced by the reaction between $Mg^{2+}$ and $OH^-$.

• Analytical Science and Technology
• /
• v.14 no.1
• /
• pp.80-87
• /
• 2001

This research was studied the action of the coupling ozone-hydrogen peroxide on aqueous humic acid. PEROXONE process is enhanced the generation of hydroxyl radicals which is effective for degradation of organic matters. Therefore the changes of $UV_{254}$ and TOC were investigated through the change of concentrations, injection time of $H_2O_2$, initial pH of aqueous humic acid and concentrations of radical savenger as $HCO_3{^-}$ in the PEROXONE processes. And the GC/ECD was used to detect the formaldehyde formed by ozonation of humic acid. From the experimental results, concentrations and injection time of $H_2O_2$ and initial pH in solution in the PEROXONE processes were very important for enhancing the efficiency of degradation in humic acid. The results indicated that removal efficiency of TOC was the highest when concentration of $H_2O_2$ was 5mg/L, injection time of $H_2O_2$ was 5 minutes and initial pH in solution was 10.5. And presence of alkalinity in solution was reduced the efficiency of treatment. The formaldehyde were formed less PEROXONE processes than only ozone. When initial pH in solution were changed from 3.5 to 10.5, the formaldehyde were formed highest concentration at pH 5.

• Clean Technology
• /
• v.13 no.4
• /
• pp.266-273
• /
• 2007

The adsorption properties of the activated carbon-based adsorbents were studied to remove COS emitted from $SO_2$ catalytic reduction process on the integrated gasification combined cycle (IGCC) system in this work. Transition metal supported catalysts and mixed metal oxide catalysts were used for the $SO_2$ catalytic reduction. The mechanism of COS produced from the $SO_2$ reduction and the COS concentration s according to the reaction temperature were investigated. In this study, an activated carbon and a modified activated carbon doped with KOH were used to remove the very low concentration of COS effectively. The adsorption rate and the breakthrough time of COS were measured by a thermo gravity analyzer (TGA, Cahn Balance) and a fixed bed flow reactor equipped with GC-pulsed flammable photometric detector (PFPD), respectively. It was confirmed that the COS breakthrough time of the activated carbon doped with KOH was longer than that of an activated carbon. In conclusion, the modified-activated carbon having a high surface area showed a high adsorption rate of COS produced from the $SO_2$ reduction.

• Korean Journal of Microbiology
• /
• v.45 no.1
• /
• pp.63-68
• /
• 2009

The exo-polysaccharide producing microorganism, Aureobasidium pullulans IMS-822, was isolated and identified from soil. The viscosity-average molecular weight of exo-polysaccharide was calculated as $8.9{\times}10^5$ by Mark-Houwink equation. The sugar component of exo-polysaccharide was determined as glucose by HPLC analysis. The IR spectra indicated that the exo-polysaccharide has an absorption peak at 890 $cm^{-1}$ for the ${\beta}-configuration$ of D-glucan. The $^{13}C$ NMR signal at ${\delta}$ 86.62 ppm arose from the substituted C-3 of glucose. The signal at ${\delta}$ 72.11 ppm was assigned to C-6 of branched ${\beta}-(1{\to}3)-D-glucosyl$ residues. Viscosity and Congo red reaction indicated that {\beta}-(1{\to}3)(1{\to}6)-glucan$ produced by A. pullulans IMS-822 has a highly ordered hydrogen-bond dependent conformation in aqueous solution, which collapses in strong alkaline solution.

• Membrane Journal
• /
• v.28 no.3
• /
• pp.157-168
• /
• 2018

Potassium tannate (TA-K), which is prepared by base treatment of the bio-renewable tannic acid (TA), was evaluated for its potential application as a draw solute for water purification by forward osmosis. The forward osmosis and recovery properties of TA-K were systematically investigated. In the application of forward osmosis through the active layer facing feed solution (AL-FS) method, the water flux of TA-K draw solution was significantly higher than that of the TA draw solution, while that of the latter was not identified. At a low concentration of 100 mM, the osmotic pressure (1,135 mOsmol/kg) of the TA-K draw solution was approximately 6.5 times that (173 mOsmol/kg) of the NaCl draw solution. Furthermore, the water flux and specific salt flux (6.14 LMH, 1.26 g/L) of the TA-K draw solution at 100 mM were approximately 2.5 and 0.5 times those of the NaCl draw solution (2.46 LMH, 2.63 g/L) at the same concentration, respectively. For reuse, TA-K was precipitated by using a metal ion and recovered through membrane filtration. This study demonstrates the applicability of a phytochemical material as a draw solute for forward osmosis.

• Analytical Science and Technology
• /
• v.31 no.1
• /
• pp.47-56
• /
• 2018

Finding the blood left at a crime scene is very important to reconstruct or solve a criminal case. Although numerous reagents have been developed for use at crime scenes, luminol is the most representative. Bluestar Forensic has been used in recent years, but is expensive and cannot be stored after preparation. This study aims to develop a new luminol reagent that can be stored for a long period of time while maintaining the chemiluminescence intensity at the level of Bluestar Forensic. Because luminol dissolves well in aqueous alkaline solutions, the use of sodium hydroxide in the preparation of luminol reagents can promote the decomposition of hydrogen peroxide. Magnesium sulfate, sodium silicate, and potassium triphosphate have been used as hydrogen peroxide stabilizers. The effects of the addition of these substances on the chemiluminescence emission intensity and the storage period of the luminol reagents were confirmed. The addition of a hydrogen peroxide stabilizer was shown to have no significant affect on the chemiluminescence emissions intensity or stabilized pH of the luminol reagent during storage. It also greatly increases the shelf life of the reagents. The use of magnesium sulfate as a hydrogen peroxide stabilizer is the most appropriate. When sodium perborate is used instead of hydrogen peroxide as an oxidizing agent, there is no significant change in the sensitivity and chemiluminescence emissions intensity, but the storage period is shortened. However, after the reaction with blood, the pH of the mixed solution does not increase significantly, and is judged to be more suitable than a reagent made of hydrogen peroxide.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.768-776
• /
• 1996

Carbon Black has various advantageous properties such as reinforcement, tinting, weathering, chemical resistance, electrical resistance, etc., but it has poor affinity in the solution. The purpose of this study is to enhance dispersion in the aqueous solution by altering the surface characteristics. Two different treatments were applied for both channel black and furnace black respectively. Channel black was treated in alkaline solution to replace hydrogen of the carboxyl group with alkaline metal, Li, Na, K. Furnace black has few functional groups, and it was treated with $HNO_3$ to increase the number of functional group on carbon black. It was seen that the substitution of alkaline metal on the surface of channel black enhances the degree of dispersion. Also the higher the acid concentration and reaction temperature, the more the number of some functional groups on the furnace black. Reaction time was not seen to be effective.

• Journal of Conservation Science
• /
• v.26 no.4
• /
• pp.397-406
• /
• 2010

The most ideal method to measure the water-soluble $Cl^-$ ion eluted from iron artifacts is conducting the analysis on desalting solution by Ion Chromatography. But most institutes related to cultural heritages use Cl meter by reason of lack of budget and experts. This study evaluated reliability and stability between Cl meter and Ion Chromatography by doing cross-validation with results from two methods to detect $Cl^-$ ion of desalting solution. From D.I water, extremely small quantities of $Cl^-$ ion was detected by the influence of remaining water-soluble $Cl^-$ ion at the electrode of Cl meter and water-soluble $Cl^-$ which remains in Sodium sesquicarbonate, components of reagent was detected as well. The first desalting solution had the most $Cl^-$ ions, $Cl^-$ ion slightly decreased from the second to the fourth desalting solution and tend to decrease again at the stage of dealkalified in D.I water. Each Cl meter has the standard deviation according to the measured numbers and the higher concentration of $Cl^-$ ion the desalting solution has, the wider the deviation is. But when the concentration of $Cl^-$ ion is low, it was stable to use Cl meter to detect the concentration of $Cl^-$ ion from iron artifacts because there is the small deviation, It is thought that conductivity meter method is not suitable for measuring $Cl^-$ ion, because the electrical conductivity of alkaline solution is too high to measure $Cl^-$ ion.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.532-540
• /
• 2019

PET microfibers with various diameters (0.5, 0.2, 0.06, and 0.01 dpf) were dyed with a dispersed dye (C.I. Disperse Blue 56) at various temperatures. The dyeing process was conducted under infinite dyebath conditions at constant temperatures. The effects of the dyeing temperature and diameter on the partition coefficient, affinity, and diffusion coefficient of disperse dyes were studied. The curve of isotherms was fitted well to Nernst-type model in a large range of initial dye concentrations. At the same temperature, the partition coefficient and affinity decreased with increasing sample diameter due to the increase in surface area. At all deniers, the partition coefficient and affinity decreased with increasing temperature because the dyeing process is an exothermic reaction. In addition, the decrease in radius of the sample gives rise to a decrease in the heat of dyeing. The fine diameter of the sample resulted in an increased surface area but decreased space between the microfibers. Consequently, decreasing the diameter of the microfibers leads to a decrease in the diffusion coefficient. At the same diameter, the diffusion coefficient increased with increasing temperature because of rapid dye movement and the large free volume of the sample inside. In addition, thermal dependence of the diffusion coefficient increased when the diameter of the sample increased.