• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.76.2-76
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.222.1-222
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.86.2-86
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.138.2-138
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.186.1-186
• /
• 2002

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.89-94
• /
• 2019

Glass base sealant is required as a ceramic-ceramic joining material between α-alumina insulation cap and β-alumina electrolyte tube in the development of NaS battery cell package for electrical energy storage system. The fabrication of glass frit by thermal quenching method, phase analysis, particle size analysis, coefficient of thermal expansion and surface roughness according to the glass compositions were analyzed for the fabrication of glass sealing paste for ceramic-ceramic joining. Also, a new evaluation method of the adhesion strength of glass sealant at the small area in ceramic-ceramic joining component was proposed using conventional Dage bond tester that was used to measure the adhesion of solder ball joint.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.347-347
• /
• 2008

본 연구에서는 별도의 소결과정 없이 상온에서 치밀한 복합체 후막의 제조가 가능한 Aerosol Deposition Method (ADM)를 이용하여 SOP를 실현시키기 위한 기판 재료로서 알루미나 기반의 알루미나-폴리이미드 복합체를 제조하고 그 특성에 대한 평가를 진행하였다. SEM 관찰결과 기공이 거의 없고 치밀한 구조의 복합체가 상온에서 성공적으로 형성되었음이 확인되었다. XRD 와 FT-IR 분석 결과 알루미나와 폴리이미드 모두가 복합체에 존재함을 확인할 수 있었다. 또한 XRD 분석결과 출발 원료에 폴리이미드 함량이 증가할수록 ADM으로 제조된 복합체 내부의 알루미나의 결정자 크기가 증가하는 결과를 보였다. 복합체의 알루미나 충진율을 확인하기 위한 간접적인 방법으로 복합체 후막을 연마하여 복합체 내부를 노출시킨 후 폴리이미드의 용매인 Methyl Ethyl Ketone으로 폴리이미드를 식각시켜 남아있는 알루미나 영역을 관찰한 SEM 분석결과 알루미나가 60% 이상 복합체의 대부분을 이루고 있다는 사실을 관찰할 수 있었다. 복합체의 미세구조를 확인하기 위하여 TEM 분석결과 기존에 보고된 ADM으로 제조된 알루미나 후막의 결정자 크기인 10~20 nm 보다 큰 100 nm 범위의 결정자 크기를 관찰 할 수 있었다. 유전특성평가 결과 유전율과 tan$\delta$는 1 MHz에서 각각 9.0, 0.0072로서 알루미나만을 원료로 성막시킨 후막의 유전 특성을 크게 떨어뜨리지 않으며 알루미나 후막과 유사한 결과를 보였다. 추후 복합체의 균일성 향상 및 고주파 영역의 유전 특성 향상을 통하여 세라믹의 취성 및 가공성이 개선된 3 차원 적층 기판재료로의 응용이 기대될 것으로 전망된다.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1083-1089
• /
• 2002

Densification and grain growth behavior of MgO and -doped alumina ceramics were investigated. MgO was found to inhibit grain growth and to promote densification, but acted to promote grain growth more than densification. The density which showed the maximum shrinkage rate was investigated in the plot of shrinkage rate versus density. The data suggests that the maximum shrinkage rate separates the two kinetic regimes, below the density of maximum shrinkage, the regime associated with densification and above the maxima, the regime associated with the grain growth. The plot exhibits a maximum which shifts to higher temperatures with MgO doping and to lower with doping.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.339-347
• /
• 1996

Mechanical properties(flexural strength hardness fracture toughness) of alumina ceramics were evaluated. Alumina products of four companies were selected and three of those were made in Korea and one of those was made in Japan. The large differences according to manufacturing companies had resulted from flexural strength and weibull modulus which had a wide ranges of 300 to 400 MPa and 5 to 15 respectively. Critical indenstation load which could be neglected the effect of elastic recovery was about 9.8N and Vickers' hardness were about 15 GPa. Fracture toughnesses were evaluated by IF and ISB method. It was more preferable to the average at one indentation load that fracture toughness were obtained from the slope of the relationship between indentation load and crack length in IF method and between indentation load and fracture load in ISB method and fracture toughness was about 4 MPa·m1/2.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.110-116
• /
• 2005

Suitable compositions which are sinterable at low temperature in the $BaO-B_{2}O_{3}-ZnO$ glass system were investigated as a function of the ratio between BaO and ZnO. The effect of $Al_{2}O_3$ filler on densification and physical characteristics of the glass was also examined. When the amount of $Al_{2}O_3$ filler increased, the densification rate and the values of dielectric constant, thermal expansion coefficient and hardness in the glass-filler composites decreased gradually. The decreasing rate of the physical properties accelerated when fine $Al_{2}O_3$ filler was used. However, the fracture toughness of the composite rather increased due to the existence of filler particles and pores which effectively suppressed crack propagation with addition of fine $Al_{2}O_3$ filler.