• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.509-509
• /
• 2016

본 연구에서는 원주천 16 km 구간을 대상으로 안정하도 설계를 위한 하천구조물의 개선 재배치 철거에 따른 물리적 교란과 생물학적 교란을 분석하였으며, 그에 따른 구조물의 최적 배치 방안을 도출하였다. 대상구간은 20개 구간으로 나누었으며, Engelund-Hansen 공식을 이용하여 안정하도를 평가하였다. 원주천의 안정하도 설계를 위한 21개의 구조물 배치 시나리오를 도출하였으며, 1차원 HEC-RAS 수치모의를 통해 시나리오별 5년 후의 수리특성과 하상변동 결과에 따른 안정하도와 물리적 교란개선 평가를 실시하였다. 현재의 원주천에서는 총 20개 구간 중 17개 구간에서 안정하도로 나타났으며, 3개 구간에서 불안정으로 나타났다. 물리적 교란개선 평가 결과는 평균 120.1점으로 나타났다. 현 상태를 제외한 20개 시나리오에 따른 구조물의 재배치 후 안정하도 평가와 물리적 교란개선 평가를 수행한 결과 제시한 최적의 구조물 배치 결과는 총 20개 구간 중 19개 구간에서 안정, 1개 구간에서 불안정 평가가 나타났으며, 물리적 교란개선 평가 결과는 125.28점으로 구조물의 재배치 후 안정하도 구간과 교란개선 평가 결과가 증가하였다. 생물학적 교란 평가는 PHABIM 모형을 이용하였으며, 원주천의 대표어종인 갈겨니의 서식적합도(HS, habitat suitability)와 가중가용면적(WUA, weighted usable area)을 분석하였다. 현 상태의 경우 HS는 0.21, WUA는 $508m^2$으로 나타났으며, 현 상태에서 5년경과 후의 HS는 0.19, WUA는 $403m^2$으로 나타났다. 아울러 최적 구조물 배치 시나리오의 평가 결과는 HS가 0.19, WUA가 $382m^2$으로 나타났으며, 구조물 재배치 후 HS와 WUA가 현 상태보다 다소 감소하였으나 현 상태에서의 5년경과 후의 결과와 유사하게 나타났다. 따라서 원주천에서의 어류 서식적합도와 안정하도 설계 및 물리적 교란개선을 향상할 수 있는 최적 구조물 배치를 제시하였다.

• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.605-618
• /
• 2018

Korea follows the slope design criteria during construction. It was enacted by the Ministry of Land, Transport and Maritime Affairs. There are cases where the Soil-nail is designed as a measure to secure slope stability. The arrangement of the soil-nail may be arranged at equal intervals or may be arranged differently depending on the soil failure model. The optimum design of the countermeasure method is determined by securing stability of the slope through optimization of dimensions and shape. However, when uniform nails are placed at low elevations in slopes, the standard safety factor is exceeded, which may hinder economic design. It is preferable to arrange the reinforcement of the nails over the entire slope. When the horizontal spacing of the nails was topology optimized according to the slope height, it was possible to minimize the amount of reinforcement while satisfying the standard safety factor. Since the active load is reduced in the section where the slope height is lowered, the safety factor after reinforcement may be excessively increased. Therefore, the phase optimization method is proposed as an economical optimal design method using the reinforcing shape density. In addition, a relational expression was designed to optimize the horizontal spacing by slope height.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.650-654
• /
• 2008

친환경 공법의 수리적인 안전성 검토는 식생 및 자연재료의 물리적 특성, 하천의 수리 수문학적 특성, 유사특성과 이들의 상호관계 등에 대한 분석이 요구되며, 이에 선행하여 분석에 이용되는 장기간의 충분한 자료가 구축되어 있어야 한다. 그러나 우리나라의 경우 이러한 자료는 부족한 실정이며, 주로 시범구간을 통한 제한된 자료만이 이용되고 있을 뿐이므로 수리학적 치수방재적 측면에서 친환경 공법의 안전성 평가에 있어 많은 어려움을 겪고 있다. 본 연구에서 수질정화체의 배치 변화를 통한 수치해석 통하여 수심 및 유속분포를 비교 분석하여 수로의 3차원적 흐름특성을 파악하고, 실제 대상수로에 수질정화체를 설치하여 수로의 수리적 안정성을 연구하였다. FLOW-3D와 수리모형시험 그리고 대상수로 모니터링을 각 경우에 따라 유속, 수위를 측정하여 다양한 조건에 대한 흐름 특성을 연구하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.7
• /
• pp.125-132
• /
• 2002

This paper shows an experimental magnetic levitation table using one degree-of-freedom active control. The magnetic levitation table using repulsions of permanent magnets was theoretically presented already. Thus the objective of this paper is to prove stable levitation with only one degree-of-freedom active control experimentally. For the design of the system, at first, permanent magnets are selected. Secondly, the spring constants of the virtual spring are obtained by simulation. Thirdly, the moving magnets are arranged using a stable layout relation. Fourthly, a linear voice coil motor is designed. Finally, the magnetic levitation system is manufactured. The phenomenon of stable levitation in the manufactured table is proven by means of dynamic time and frequency responses. The differences between the theoretical natural frequencies and experimental ones are analyzed. Also, stable range in the control direction is shown experimentally.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.20-27
• /
• 2020

In general, a nonlinear system is linearized in the form of a multiplication of the 1st and 2nd order system. This paper reports a design method of a weighting matrix and control law of LQ control to move the double poles that have a Jordan block to a pair of complex conjugate poles. This method has the advantages of pole placement and the guarantee of stability, but this method cannot position the poles correctly, and the matrix is chosen using a trial and error method. Therefore, a relation function (𝜌, 𝜃) between the poles and the matrix was derived under the condition that the poles are the roots of the characteristic equation of the Hamiltonian system. In addition, the Pole's Moving-range was obtained under the condition that the state weighting matrix becomes a positive semi-definite matrix. This paper presents examples of how the matrix and control law is calculated.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.6 no.2
• /
• pp.43-50
• /
• 1992

In this paper, application of decoupling control method of multivariable system by state feedback to turbo-generating system with 2-input and 2-output is studied. The results of simulation shows tat turbo-generating system is canonically decoupled, and can be controlled against the change of load or frequency by feedback gain.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.2
• /
• pp.215-220
• /
• 2011

A 0.5 t/h class non-furnace boiler has been developed with the aim of achieving a high efficiency and compactness. A metal fiber burner has been adopted so that a stable flame can be obtained. The tube banks are installed downstream of the burner. Bare tubes are used upstream, while finned tubes are installed downstream. The heat-transfer characteristics of the non-furnace boiler have been studies on the basis of the results of the numerical simulation as well as those of the experiment. Important design parameters such as the bulk temperature along the streamwise direction and the temperature of the fin tips have been evaluated using the CFD results and compared with the experimental data and the empirical correlations typically used for the design of the boiler.

• Convergence Security Journal
• /
• v.17 no.3
• /
• pp.83-93
• /
• 2017

The U.S.-China Relations could be analyzed two perspectives and their basis under major international p olitics theory-power transition with conditions: (1) North Korean's nuclear puzzle, (2) THAAD in the Kor ean Peninsula and (3) the U.S.-ROK Alliance. One perspective is the global order dominates the regional order, and then stable regional order comes out. The other is the regional order dominates the global ord er, and China wages a regional hegemonic conflict against the United States. Consequently, America's o verwhelming leadership in North Korean's nuclear, THAAD and U.S.-ROK Alliance as national power is expected to endure. But China also has expected empowerment and cooperation for the peace and stabilit y on the Korean Peninsula military problems. In this perspective, South Korea needs to pay attention to the changing power distribution and competition between the U.S. and China and needs to strengthen a balancing and harmonious diplomatic strategy, so called 'see-saw diplomacy'.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.1
• /
• pp.15-27
• /
• 2007

Over the past decade, labor costs have increased relative to the cost of material hardware according to analysts in the construction industry. Therefore, the minimum weight design, which has been widely adopted in the literature for the optimal design of steel structures, is no longer the most economical construction approach. Presently, although connection- related costs is crucial in determining the most cost-effective steel structures, most studies on this subject focused on minimum-weight design or engaged in higher analysis. Therefore, in this study, we proposed a fabrication scheme for the most cost-effective moment-resisting steel frame structures that resist lateral loads without compromising overall stability. The proposed approach considers the cost of steel products, fabrication, and connections within the design process. The optimal design considered construction realities, with the optimal trade-off between the number of moment connections and total cost was achieved by reducing the number of moment connections and rearranging them using the combination of analysis that includes shear, displacement and interaction value based on the LRFD code and optimization scheme based on genetic algorithms. In this study, we have shown the applicability and efficiency in the examples that considered actual loading conditions.

• Journal of Korea Water Resources Association
• /
• v.35 no.6
• /
• pp.665-675
• /
• 2002

It is very closely related with the reliability of the pipe network to predict pipe burst and diminish burst effect in water distribution system. Most of the engineers have not consider pipe layout and the effect of pipe burst in conservative pipe network design. In this study, The effect of pipe burst in the network is analyzed with respect to pipe network geometric topology and the method of increasing the system reliability is presented by reducing pipe-burst effect. In existing pipe system, it is only designed to the closed loop system but in case of each pipe burst, it cannot transmit appropriate water to consumers and occurs severe hydraulic head drop in many nodes. The techniques developed in this study allow proper pipe diameter and pipe layout to pipe system through the analysis of pipe-burst effect. Thus, when each pipe is bursted, pipe system is prevented from severe pressure head drop in demand nodes and can supply stable flowrate to consumer.