• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.804-811
• /
• 2010

The lower portion of sloping paddy fields normally contains excessive moisture and the higher water table caused by the inflow of ground water from the upper part of the field resulting in non-uniform water content distribution. Four drainage methods namely Open Ditch, Vinyl Barrier, Pipe Drainage and Tube Bundle for multiple land use were installed within 1-m position from the lower edge of the upper embankment of sloping alluvial paddy fields. Knowledge of the spatial variability of soil water properties is of primary importance for management of agricultural lands. This study was conducted to evaluate the effect of drainage in the soil on spatial variability of soil water content using the geostatistical analysis. The soil water content was collected by a TDR (Time Domain Reflectometry) sensor after the installation of subsurface drainage on regular square grid of 80 m at 20 m paddy field located at Oesan-ri, Buk-myeon, Changwon-si in alluvial slopping paddy fields ($35^{\circ}22^{\prime}$ N, $128^{\circ}35^{\prime}$). In order to obtain the most accurate field information, the sampling grid was divided 3 m by 3 m unit mesh by four drainage types. The results showed that spatial variance of soil water content by subsurface drainage was reduced, though yield of soybean showed the same trends. Value of "sill" of soil water content with semivariogram was 9.7 in Pipe Drainage, 86.2 in Open Ditch, and 66.8 in Vinyl Barrier and 15.7 in Tube Bundle.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.1
• /
• pp.4-31
• /
• 2018

The Neolithic pottery excavated from the Jungsandong site has been classified into four types of pottery (I: feldspar type, II: mica type, III: talc type and IV: asbestos type) according to their mineral composition. These four types of potteries generally appear to have undergone incomplete firing, while the level of oxidation in the type I pottery objects, which have a relatively higher clay content, was found to be particularly low. The type III objects, which have a high talc content, are judged to have been somewhat slow in removing carbon because they contain saponite belonging to the smectite group. Of the four types of pottery, type IV showed the highest redness and the most uniform characteristics, thus indicating a good level of oxidation. In particular, fixed carbide (C; 33.7 wt.%) with a thickness of about 1mm, and originating from organic substances, was detected inside the walls of the type I pottery, while the deep radial cracks in the outer surfaces of the pottery are thought to have been caused by repeated thermal shocks. Given that all of the pottery except for the type I artifacts are considered to be have been made for storage purposes, those containing talc and tremolite are easy to done liquid storing vessels based on an analysis of their material characteristics. As for the type II relics, which are composed of various minerals and exhibit poor physical properties, they seem to have been used for simple storage purposes. As domestic talc and asbestos mines were concentrated in the areas of Gyeonggi, Gangwon, Chungbuk, and Chungnam, it seems likely that talc and tremolite were produced as contiguous minerals. Considering the distance between the remains in Jungsandong and these mines and their geographical distribution, there is a possibility - albeit somewhat slight - that these mines were developed for the mining of various minerals. Although ultramafic rock masses - such as serpentine capable of generating talc and tremolite - have not been found in the Jungsandong area, limestone and biotite granite containing mica schist have been identified in the northwestern part of Yeongjong Island, indicating that small rock masses might have formed there in the past. Therefore, it is judged necessary to accumulate data on pottery containing talc and tremolite, other than the remains in Jungsandong, and to investigate the rocks and soils in the surrounding area with greater precision. The firing temperatures of the pottery found at the Jungsandong site were interpreted by analyzing the stability ranges of the mineral composition of each type. As a result, they have been estimated to range from 550 to $800^{\circ}C$ for the type I artifacts, and from 550 to $700^{\circ}C$ for the type I, II and IV artifacts. However, these temperatures are not the only factors to have affected their physical properties and firing temperature, and the types, particle sizes, and firing time of the clay should all be taken into consideration.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.1
• /
• pp.36-42
• /
• 2019

A macroporous Sn thick film as a high capacity negative electrode for a lithium ion secondary battery was prepared by using a chemical etching method using nitric acid for a Sn film having a thickness of $52{\mu}m$. The porous Sn thick film greatly reduced the over-voltage for the alloying reaction with lithium by the increased reaction area. At the same time. The porous structure of active Sn film plays a part in the buffer and reduces the damage by the volume change during cycles. Since the porous Sn thick film electrode does not require the use of the binder and the conductive carbon black, it has substantially larger energy density. As the concentration of nitric acid in etching solution increased, the degree of the etching increased. The etching of the Sn film effectively proceeded with nitric acid of 3 M concentration or more. The porous Sn film could not be recovered because the most of Sn was eluted within 60 seconds by the rapid etching rate in the 5 M nitric acid. In the case of etching with 4 M nitric acid for 60 seconds, the appropriate porous Sn film was formed with 48.9% of weight loss and 40.3% of thickness change during chemical acid etching process. As the degree of etching of Sn film increased, the electrochemical activity and the reversible capacity for the lithium storage of the Sn film electrode were increased. The highest reversible specific capacity of 650 mAh/g was achieved at the etching condition with 4 M nitric acid. The porous Sn film electrode showed better cycle performance than the conventional electrode using a Sn powder.

• Korean Journal of Heritage: History & Science
• /
• v.42 no.3
• /
• pp.106-130
• /
• 2009

The aim of this paper is analysis of structure and development pattern about wooden coffin and chamber tombs in Gyeongju from the 2nd century B.C. to the 3rd century A.D. for researching to socio-political tendency and growth process of Sarokuk. Tombs buried with iron objects were built in Youngnam(嶺南) from the 2nd century B.C. with spread wooden coffin with stone mound(積石木棺墓). Also medium or small sized wooden coffin tombs buried with bronze mirror of western Han(前漢) and soft stoneware(瓦質土器) were appeared the 2nd century B.C. in Gyeongju, because of establishment of Han's commanderies(漢郡縣) in the Korean Peninsula and refuge from Daedong river(大同江) to Jinhan(辰韓). Separate tombs(獨立墓) with lots of bronze object ware assumed high ranked tombs of parsonage(司祭王) or local chief(地域首長). From the 2nd century A.D. the size of wooden coffin tombs became enlarged and funerary objects ware abundant, for example Sarari 130th tomb(舍羅里 130號). The burying pattern of this tomb is similar to wooden chamber tombs in Lelang(樂浪), which had prestige goods like lacquer ware and bronze mirror in wood box(木匣) beside coffin. Appearance of these wooden chamber tombs that were different from original wooden coffin tombs imply interaction between Lelang and these area with iron. Sarari community that held right of trade and distribution to outside through the geographical advantage grew up centered position in Gyeongju politically, socially, and culturally. Chamber in tomb as a new structural notion that can secure funerary objects became firmly was established from the 2nd century A.D. in Gyeongju and large sized wooden chamber tombs were generally built early of the 3rd century A.D. This tendency was reflected in stratification of community and growth as center of local state. After late of the 3rd century A.D. Gyeongju type wooden chamber tomb(慶州式木槨墓) which had subordinate outer coffin(副槨) was appeared and then subordinate outer coffin was as bigger as main chamber(主槨) the 4th century A.D., because of centralization and stratification in society and unification of various communities among the Gyeongju area.

• The Southeast Asian review
• /
• v.27 no.2
• /
• pp.245-271
• /
• 2017

The purpose of this study is to examine and assess the major characteristics and changes of politics, economy, and diplomacy in Thailand in 2016. Specifically, it reviewed the New Constitution that was passed in 2016, the confrontation between different political forces and the trend of military regime around the New Constitution, and the political instability caused by the accession of the new king to the throne. This study also set out to figure out changes to the economy and foreign relations of the country, including its relations with South Korea, under the military regime and make predictions for the impact and future prospects of King Bhumibol Adulyadej's death on the politics and economy of the country. In 2016, the politics of Thailand took a step further toward the transfer of power to civil government and established a foundation for an authoritarian system. The draft of the New Constitution, which does not seem to be democratic, was approved by a referendum and enabled the military authorities to continue their political interventions, even after the general election. The New Constitution, in particular, reduces the power of political parties itself in addition to simply keeping the Thaksin's party in check; thus, anticipating ongoing conflicts between the military authorities and political parties. In this situation, the absence of King Bhumibol Adulyadej, who used to play a decisive role in promoting the political stability of the country, and the accession of the new king to the throne raise concerns about the acceleration of political instability, which has continued after the coup and influenced the diplomatic relations of the country. Today, Thailand is distancing itself from Western nations that do not recognize the current military regime including the U.S.A. and EU member states and instead maintains a rapidly friendly and close relation with China. In 2016, the economy of Thailand made a gradual recovery rather than high growth. The death of King Bhumibol Adulyadej has exerted limited direct economic impacts only on individual consumption and tourism and is not likely to cause a recession. An economic crisis will, however, be unavoidable if the political confrontations escalate before the general election to transfer power to the civil government.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.1
• /
• pp.1-10
• /
• 2023

The cathode, which is one of the four major components of a lithium secondary battery, is an important component responsible for the energy density of the battery. The mixing process of active material, conductive material, and polymer binder is very essential in the commonly used wet manufacturing process of the cathode. However, in the case of mixing conditions of the cathode, since there is no systematic method, in most cases, differences in performance occur depending on the manufacturer. Therefore, LiMn₂O₄ (LMO) cathodes were prepared using a commonly used THINKY mixer and homogenizer to optimize the mixing method in the cathode slurry preparation step, and their characteristics were compared. Each mixing condition was performed at 2000 RPM and 7 min, and to determine only the difference in the mixing method during the manufacture of the cathode other experiment conditions (mixing time, material input order, etc.) were kept constant. Among the manufactured THINKY mixer LMO (TLMO) and homogenizer LMO (HLMO), HLMO has more uniform particle dispersion than TLMO, and thus shows higher adhesive strength. Also, the result of the electrochemical evaluation reveals that HLMO cathode showed improved performance with a more stable life cycle compared to TLMO. The initial discharge capacity retention rate of HLMO at 69 cycles was 88%, which is about 4.4 times higher than that of TLMO, and in the case of rate capability, HLMO exhibited a better capacity retention even at high C-rates of 10, 15, and 20 C and the capacity recovery at 1 C was higher than that of TLMO. It's postulated that the use of a homogenizer improves the characteristics of the slurry containing the active material, the conductive material, and the polymer binder creating an electrically conductive network formed by uniformly dispersing the conductive material suppressing its strong electrostatic properties thus avoiding aggregation. As a result, surface contact between the active material and the conductive material increases, electrons move more smoothly, changes in lattice volume during charging and discharging are more reversible and contact resistance between the active material and the conductive material is suppressed.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.1
• /
• pp.67-74
• /
• 2023

In this study, for a natural cosmetics market, we sought to explore alternatives that can replace polyvinyl alcohol (PVA) of peel-off packs. A peel-off type pack was prepared by combining pullulan, a water-soluble polysaccharide, and other polysaccharides (sodium hyaluronate, cellulose gum, hydroxyethyl cellulose, sodium alginate, corn starch), and the pH, viscosity, and stability against temperature of each peel-off type pack were confirmed. The thickness and tensile strength of the manufactured film were measured for comparison with the PVA peel-off type pack, and applicability, drying speed, and removal degree were measured. Among them, the pullulan-sodium hyaluronate peel-off type pack showed excellent film formation ability to replace the peel-off type pack containing PVA with 5.12% thin film thickness and 4.23% high film tensile strength. When applied to actual skin, the degree of spread of the pack, the usability that can be uniformly applied, and the formation and removal strength of the film when removed after drying were also similar to the peel-off type pack containing PVA. Therefore, it was confirmed that the film formed of pullulan-sodium hyaluronate showed enough physical properties to replace the PVA of the peel-off type pack as a natural peel-off type pack.

• Korean Journal of Remote Sensing
• /
• v.40 no.1
• /
• pp.19-31
• /
• 2024

Ports are vital social infrastructures that significantly influence both people's lives and a country's economy. In South Korea, the aging of port infrastructure combined with the increased frequency of various natural disasters underscores the necessity of displacement monitoring for safety management of the port. In this study, the time-series displacements of Yeongilman Port and surrounding areas in Pohang, South Korea, were measured by applying Permanent Scatterer Interferometric Synthetic Aperture Radar (PSInSAR) to Sentinel-1 SAR images collected from the satellite's ascending (February 2017-July 2023) and descending (February 2017-December 2021) nodes, and the displacement associated with the 2017 Pohang earthquake in the port was analyzed. The southern (except the southernmost) and central parts of Yeongilman Port showed large displacements attributed to construction activities for about 10 months at the beginning of the observation period, and the coseismic displacement caused by the Pohang earthquake was up to 1.6 cm of the westward horizontal motion and 0.5 cm of subsidence. However, little coseismic displacement was observed in the southernmost part of the port, where reclamation was completed last, and in the northern part of the oldest port. This represents that the weaker the consolidation of the reclaimed soil in the port, the more vulnerable it is to earthquakes, and that if the soil is very weakly consolidated due to ongoing reclamation, it would not be significantly affected by earthquakes. Summer subsidence and winter uplift of about 1 cm have been repeatedly observed every year in the entire area of Yeongilman Port, which is attributed to volume changes in the reclaimed soil due to temperature changes. The ground of the 1st and 2nd General Industrial Complexes adjacent to Yeongilman Port subsided during the observation period, and the rate of subsidence was faster in the 1st Industrial Complex. The 1st Industrial Complex was observed to have a westward horizontal displacement of 3 mm and a subsidence of 6 mm as the coseismic displacement of the Pohang earthquake, while the 2nd Industrial Complex was analyzed to have been little affected by the earthquake. The results of this study allowed us to identify the time-series displacement characteristics of Yeongilman Port and understand the impact of earthquakes on the stability of a port built by coastal reclamation.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.902-909
• /
• 2023

This study evaluated the performance test of a small-sized LTE-Maritime(LTE-M) transceiver that was developed and promoted to expand the use of intelligent maritime traf ic information services led by the Ministry of Oceans and Fisheries with the aim of supporting the prevention of maritime accidents. Accoriding to statistics, approximately 30% of all marine accidents in Korean water occur with ships weighing less than 3 tons. Therefore, the blind spots of maritime safety must be supplemented through the development of small-sized transceivers. The small transceiver may be used in fishing boats that are active near coastal waters and in water leisure equipment near the coastline. Therefore, verifying whether sufficient performance and stable communication quality are provided is necessary, considering the environment of their real usage. In this study, we reviewed the communication quality goals of the LTE-M network and the performance requirements of small-sized transceivers suggested by the Ministry of Oceans and Fisheries, and proposed a test plan to appropriately evaluate the performance of small-sized transceivers. The validity of the proposed test method was verified for six real-sea areas with a high frequency of marine accidents. Consequently, the downlink and uplink transmission speeds of the small-sized LTE-M transceiver showed performances of 9 Mbps or more and 3 Mbps or more, respectively. In addition, using the coverage analysis system, coverage of more than 95% and 100% were confirmed in the intensive management zone (0-30 km) and interesting zone (30-50 km), respectively. The performance evaluation method and test results proposed in this paper are expected to be used as reference materials for verifying the performance of transceivers, contributing to the spread of government-promoted e-navigation services and small-sized transceivers.

• Korean Journal of Environment and Ecology
• /
• v.37 no.5
• /
• pp.367-391
• /
• 2023

This study was conducted for 10 years from 2012, which is a year before the forest road construction in Minjujisan, to 2022 to analyze annual changes in flora and vegetation before and after the forest road construction and to provide strategies for management. The plant communities in the research sites along the forest road showed the differentiation between slopes with Quercus mongolica community on the northwestern slope and Quercus variabilis and Larix kaempferi communities on the southwestern slope. A total of 212 taxa have increased for number 7 between before and after the construction from a total of 66 taxa (44 families, 59 genera, 51 species, 13 varieties, and 2 forma) in 2012 and 207 taxa (71 families, 153 genera, 176 species, 27 varieties, and 4 forma) in 2015 to 278 taxa (78 families, 172 genera, 242 species, 1 subspecies, 31 varieties, and 4 forma) in 2022. It is noteworthy that the vegetation cover and the introduction of new taxa had been expanded in the sites adjacent to the construction, which is likely caused by the significantly increased amount of light and the introduction of annual herbaceous and naturalized plants after the construction. The results of 10 years of current study reveal that the vegetation cover and the number of new taxa had rapidly increased in earlier years after the construction, slowly decreased later on, and finally formed a stable forest with the increase in the ratio of dominant species. The vegetation cover of the herbaceous layer immediately increased on the slopes along the forest road for a few years after the construction although it had continuously decreased while that of the shrub layer quickly increased. It was shown that on the hillslope the vegetation cover of tall- and low-tree layers increased whereas that of herbaceous and shrub layers rapidly decreased.