• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.5
• /
• pp.554-563
• /
• 2016

Ships are capable of operating on residual fuel oil. Recently, various attempts have been made to meet environmental regulations and with ships operating on residual fuel oil. One way of fulfilling these requirements is by using fuel additives. Dispersants and fuel combustion improvers will have a positive effect on improving the combustion characteristics of the residual fuel oil. As such, this study examines fuel oils blended with additives by using fuel combustion analysis (FIA/FCA) and thermogravimetric analysis (TGA). The results of FIA/FCA focuse only on the amount of work done by the fuel oil. Therefore, it is recommended in this study that a new method to evaluate the combustion efficiency via FIA/FCA processes be developed. The analysis with ROHR curve gained by FIA/FCA brought similar results with pressure trace curve therefore it can be said that new analysis method can be reliable. The TGA, analysis process is very sensitive to the evaporation of fuel, for example, which could be addressed. In the performance-related findings of this study, blended samples with additives containing iron compounds showed a greater improvement in early combustion characteristics than samples without additives.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.834-840
• /
• 2018

In this study, the characteristics of air pollutant emissions from ships' engines have been investigated by conducting E2 and E3 cycle mode tests. A engine 360Ps (Doosan L126TIH engine) and 400kW dynamometer Horiba-Schenck were utilized for engine tests. The FTIR analyzer and SPC were used to measure exhaust gas (NOx, SOx etc.) and PM (particulate matter), respectively. The results showed that the emissions of THC and CO produced from engine were increased with the increase of sulfur content in fuel oils at E2 and E3 cycle modes. The kinetic viscosity of the fuel increased as the sulfur content of the fuel increased, thereby the specific fuel oil consumption (SFC) of the engine improved. This result is considered to be due to improved combustion conditions due to increased average diameters of sprayed particles and due to increased kinetic viscosity under constant fuel injection pressure in this study. In the case of NOx emission, this study showed no significant change in amount of sulfur content.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.2
• /
• pp.13-21
• /
• 2020

In Korea, small reservoirs have been constructed for the supply of agricultural water, but most of them have been over 50 years from the year of construction. Aging agricultural reservoirs are being investigated for serious defects such as leaks and movements in slope, which are very vulnerable to safety. Accordingly, grouting methods are used to reinforce aging agricultural reservoirs in Korea. However, cement used as a grouting injection material consumes natural resources and generates a large amount of greenhouse gases during production. In addition, there is a problem that sufficient reinforcement is not made due to various factors such as the injection amount, the compounding ratio, the injection pressure, and etc. Therefore, due to these problems, the development of new materials and methods that can replace the grouting method and cement is required. In order to solve these problems, this study conducted an laboratory test on the surface stabilizer used to secure the stability of road and rail slopes. In addition, the program was analyzed and the reinforcing effect was examined when the surface stabilizer was used as reinforcement material for aging agricultural reservoir. As a result of the laboratory test, when the surface stabilizer is mixed, the increase of cohesion is possible up to 9% and there is no change in the friction angle. The results of the program analysis showed that the 1.0m reinforcement of slopes increased the factor of safety by 1.4 times, making it possible to reinforce the aging agricultural reservoir using surface stabilizers. And as a reinforcement method, it was analyzed that it is most appropriate to reinforce the slope and the bottom of slope simultaneously.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.1
• /
• pp.96-103
• /
• 2014

A liquefied natural gas(LNG) in cryogenic liquid is converted back into gaseous form for distribution to residential and industrial consumers. In this re-gasification process, LNG supplies a plenty of cold thermal energy about $83.7{\times}10^4kJ/kg$. The LNG cold thermal energy is utilized for the re-liquefaction process of cryogenic fluids such as Nitrogen, Hydrogen and Helium, and ice manufacturing process and air-conditioning system in some advanced countries. Therefore, it is also necessary to establish the recovery systems of the LNG cold thermal energy around Incheon, Pyungtaek and Tongyung LNG import terminals in our country. Methane is used as working fluid in this paper, which is the major component of LNG over 85 % by volume, in order to investigate the flow behavior characteristics of LNG with phase change at low heat flux. This paper presents the effects of pipe diameters, pipe inclinations and saturation pressures on the flow boundaries of methane flowing in a cryogenic heat exchanger tube, together with those of nitrogen, propane, R11 and R134a. The outcomes obtained from this theoretical researches are also compared with previous experimental data. It was also found that the effect of pipe inclination on the methane flow boundaries was significant.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.7
• /
• pp.884-891
• /
• 2016

A secondary injection system in a diesel engine has benefits: it can be controlled independently without interrupting engine control, it can be adapted to various layouts for exhaust systems, and it pose no reductant dilution problems compared to post injection systems in the combustion chamber or other supplemental reductant injections. In a secondary injection system, the efficiency of the catalyst depends on the method of reducing the supply. The reductant needs to be maintained and optimized with constant pressure, the positions and angles of injector is a very important factor. The concentration and amount of reductant can be changed by adjusting secondary injection conditions. However, secondary injection is highly dependent upon the type of injector, injection pressure, atomization, spray technology, etc. Therefore, it is necessary to establish injection conditions the spray characteristics must be well-understood, such as spray penetration, sauter mean diameter, spray angle, injection quantity, etc. Uniform distribution of the reductant corresponding to the maximum NOx reduction in the DeNOx catalyst system must also assured. With this goal in mind, the spray characteristics and impingement plate types of a secondary injector were analyzed using visualization and digital image processing techniques.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.413-421
• /
• 2004

In this paper, a structural analysis for the pressurized water reactor(PWR) spent nuclear fuel disposal canister which is deposited under the 500m deep underground is carried out to predict the creep deformation of the canister while the underground water and swelling bentonite pressure are applied on the canister. Usually the creep deformation may be caused due to the Pressure and the high heat applied to the canister even though additional external loads are not applied to the canister. These creep deformations depend on the time. In this paper, oかy the underground water and bentonite swelling Pressure are considered for the creep deformation analysis of the canister, because the heat distribution inside canister due the spent fuel is not simple and depends on time. A proper creep function is adopted for the creep analysis. The creep analysis is carried out during $10^8$ seconds. The creep analysis results show that the creep strains are very small and these strains occur usually in the lid and bottom of the canister not in the cast iron insert. A much smaller strain is found in the cast iron insert. Hence, the creep deformation doesn't affect the structural safety of the canister, and also the creep stress which shows the stress relaxation phenomenon doesn't affect the structural safety of the canister.

• Fire Science and Engineering
• /
• v.25 no.6
• /
• pp.32-38
• /
• 2011

As the using rate of an explosive gas has been increased in the industrial site, the regional residents adjacent to the site as well as the site workers have frequently fallen into a dangerous situation. Damage caused by accident in the process using hydrogen gas is not confined only to the relevant process, but also is linked to a large scale of fire or explosion and it bring about heavy casualties. Therefore, personnel in charge should investigate the kinds and causes of the accident, forecast the scale of damage and also, shall establish and manage safety countermeasures. We, in Anti-Calamity Research Center, forecasted the scope of danger if break out a fire or/and explosion in hydrogen gas facilities of MLCC firing process. We selected piping leak accident, which is the most frequent accident case based on an actual analysis of accident data occurred. We select and apply piping leak accident which is the most frequent case based on an actual accident data as a model of damage forecasting scenario caused by accident. A jet fire breaks out if hydrogen gas leaks through pipe size of 10 mm ${\Phi}$ under pressure of 120 bar, and in case of $4kw/m^2$ of radiation level, the radiation heat can produce an effect on up to distance of maximum 12.45 meter. Herein, we are going to recommend safety security and countermeasures for improvement through forecasting of accident damages.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.05a
• /
• pp.147-154
• /
• 2005

The ship plating is generally subjected to combined in-plane load and lateral pressure loads. In-plane loads include axial load and edge shear, which are mainly induced by overall hull girder bending and torsion of the vessel. Lateral pressure is due to water pressure and cargo. These load components are not always applied simultaneously, but more than one can normally exist and interact Hence, for more rational and safe design of ship structures, it is of crucial importance to better understand the interaction relationship of the buckling and ultimate strength for ship plating under combined loads. Actual ship plates are subjected to relatively small water pressure except for the impact load due to slamming and panting etc. The present paper describes an accurate and fast procedure for analyzing the elastic-plastic large deflection behavior up to the ultimate limit state of ship plates under combined loads. In this paper, the ultimate strength characteristics of plates under axial compressive loads and lateral pressure loads are investigated through ANSYS elastic-plastic large deflection finite element analysis with varying lateral pressure load level.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.382-388
• /
• 2014

This study selected five observational stations in the normal direction of Jinu-do(island) shoreline and observed water temperature, electrical conductivity and pressure from March, 2012 to January, 2013(about 11 months) and attempted to see the variation characteristics of ground watertable. This study wants to know : 1) External environment force factors(tide, climate, wave etc.) affecting ground watertable variation through time series and correlation analysis. 2) Spatial variations of ground watertable and electrical conductivity change by storm event. First, we found that the station at the intertidal zone was strongly affected by wave and tide level and the stations at sand dune and vegetation zone was affected by precipitation and tide level through time series data and correlation analysis. Second, during the storm event, we found that ground watertable and electrical conductivity are stabilized at the start line of sand dune and vegetation zone and transition zone between freshwater layer and seawater layer exists in the experiment area and is about 50~70 m from coastline of the south side of Jinu-do(island).

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.1
• /
• pp.112-121
• /
• 2017

Large eddy simulations of transitional flows around a stud installed on a flat plate have been performed to investigate an influence of grid resolution on turbulence stimulation by the stud. Because streamwise vortical structures generated by the stud played an important role in turbulence stimulation of boundary layer, streamwise vorticity was compared in the wake region behind the stud when the number of grids increased or decreased by a ratio of ${\sqrt{2}}$ in streamwise, wall-normal and spanwise directions respectively. The streamwise vorticity was shown to be mainly affected by spanwise grid resolution (${\Delta}z^+$) rather than streamwise and wall-normal grid resolution. In a viewpoint of numerical efficiency as well as physical resolution, ${\Delta}x^+{_{min}}=7.6$, ${\Delta}x^+{_{max}}=41$, ${\Delta}y^+{_{wall}}=0.25$ and ${\Delta}z^+=7.6$ was found to be desirable. Once a grid resolution was determined in each direction, a grid verification was carried out by increasing or decreasing the grid resolution y a ratio of ${\sqrt{2}}$ in all directions. The grid uncertainties of pressure and drag coefficients were 21.6 % and 2.8 % while the corrected uncertainties were 2 % and 0.3 %, respectively.