• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.21-31
• /
• 2017

In the present study, theoretical and numerical analyses have been carried out to investigate the detailed flow characteristics during the mode transition. The theoretical analysis rearranged the knowledge of gasdynamics and the previous studies, and the numerical analysis has conducted to solve the 2D unsteady compressible Navier-Stokes equations with a fully implicit finite volume scheme. To validate the numerical analysis, the experiment was compared with it. The total temperature at the inlet of isolator and the hydrogen fuel equivalent ratio were changed to investigate their effects on the mode transition phenomenon. As the results, the numerical analysis reproduced well the experiment qualitatively, the increment in the hydrogen fuel equivalent ratio induced the scram-mode to ram-mode transition which is discontinuous with a non-allowable region, and the variation in the total temperature changed the boundary of the mode transition.

• Composites Research
• /
• v.31 no.5
• /
• pp.177-185
• /
• 2018

Fiber metal laminate (FML) is a type of hybrid composites which consist of metallic and fiber-reinforced plastic sheets. As the FML has a drawback of the delamination that is a failure of the interfacial adhesive layer, the nominal stresses and the energy release rates should be determined to identify the delamination behavior. However, it is difficult to derive the nominal stresses and the energy release rates since the operating temperature of the equipment is restricted. For this reason, the objective of this paper is to predict the mode-I nominal stress and the mode-I energy release rate of the adhesive layer using the inverse analysis based on the Levenberg-Marquardt method. First, the mode-I nominal stress was assumed as the tensile strength of the adhesive layer, and the mode-I energy release rate was obtained from the double cantilever beam test. Next, the finite element method was applied to predict the mode-I delamination behavior. Finally, the mode-I nominal stress and the mode-I energy release rate were predicted by the inverse analysis. In addition, the convergence of the parameters was validated by trying to input two cases of the initial parameters. Consequently, it is noted that the inverse analysis can predict the mode-I delamination behavior, and the two input parameters were converged to similar values.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.654-662
• /
• 1998

To predict the radiating noise from the vibrating surface, it is required to know the velocity distribution of vibrating surface exactly as possible as it can. Although it can be obtained by finite element method, their accuracy is limited by theuncertainty of preparing input data such as material propoerties, damping, excitation, and the actual boundary conditions. Experimental values are accurate but are seldom available as many asthe data points compared to FEM mesh. Therefore, hybrid method of experiment and finite element method, called modal expansion technique, is investigated for the preparatin of accurate element method at specified frequencies and for the verification of this scheme, related experiment is performed. In high frequency range above 2000 Hz, piezo-electric material is used as an actuator.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.1-6
• /
• 1984

Calculation of the launch-condition dependent near field pattern, modal power distribution and far field pattern of the SGS mode scrambler by ray optical approch fits well with the experiment. These results were applied to explain how to establish the stable mode launching into the grated index multimode fiber under test by the SGS mode scrambler. The effective use of the 5G5 mode scrambler is found to restrict the launching NA as well as possible. This was also confirmed by experiment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.328-334
• /
• 2001

Up to now. vibration analysis and vibration engineering have been developed, encompassing the aspects of both experimental and analytical techniques. Using experimental modal analysis or modal testing, the mode shapes and frequencies of practical structure can be measured accurately. Curve-Fitting Method is realized through experimental modal identification. In the experimental modal parameter estimation, the estimation of modal damping factor is difficult for complicated and large structure. Also numbers of Selected mode are determined before the procedure. This paper describes the vibration shape of the super-structure model of ship through experimental modal analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.191-196
• /
• 1995

지지부에 비틀림 하중을 받는 Elstica는 비틀림 운동을 하며, 그 가진 주파수가 굽힘모드 근처일 때는 해당하는 굽힘 모드의 운동까지도 동시에 존재하게 된다. 이때 가진력의 크기가 작을때는 주기적인 운동이 된다. 가진력의 크기가 증가함에 따라 굽힘 운동은 굽힘 1차 모드와 연성된 유사주기운동이 발생하며, 이떤 범위 이상이 되면 굽힘 운동과 비틀림 운동이 결합된 진폭이 매우 크고 불규칙적인 비평면 운동(out of plane motion)이 발생하게 되며 이 때의 운동은 혼돈운동이다. Elastica가 굽힘 3차 고유진동수 근방의 주파수로 비틀림 하중을 받을 때의 정확한 이론적 해석을 위해서는 굽힘 3차모드 까지는 반영할 수 있는 식이 모델링 되어야 할 것으로 보인다. 이것은 복잡한 비평면운동을 할 때 굽힘 3차 모드까지 관찰된다는 사실에 근거한다.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.6
• /
• pp.54-61
• /
• 1998

중주파수대역은 내부 음향 모드의 공명 및 모드간 상호 간섭 특성을 완전히 무시할 수는 없으나 모드 밀도가 비교적 높기 때문에, 기존의 저주파수용 모드기법이나 고주파수에 대한 통계적 및 기하학적 해석방법과는 다른 기법이 필요한 구간이다. 본 논문에서는 위상 을 포함한 기하음향모델을 이용하여 중주파수 특성을 고려하는 개념을 이용하여 해석기법을 확립하였으며, 삼각형빔법을 기초로 한 모델링을 하였다. 세 개의 서로 다른 특성을 지닌 대 상 공간에 대해 음향 경계요소법 및 실험에 의한 음향 주파수응답함수와 본 연구 결과를 비 교함으로써 유효성과 오차특성을 검토하였다. 이로부터 위상으로 고려한 중주파수 대역에 잘 적용될 수 있음을 확인하였고, Schroeder의 차단주파수 이하의 저주파수에서는 내부구조 에 의한 회절이, 차단주파수의 네 배 이상인 고주파수에서는 벽면에서의 산란이 간섭현상과 함께 고려되어야 함을 보였다. 이러한 해석기법은 중주파수대역에 있어서 청감특성을 고려 한 내부공간의 음향설계에 매우 유용할 것으로 사료된다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.5
• /
• pp.992-998
• /
• 1992

This paper presents a method for dynamic analysis of golf club. In the analysis, the sweet spot of golf club is defined based on the magnitude of torsional vibration, and transfer matrix method is employed for numerical calculations. It is shown that the calculated natural frequencies, mode shapes and transfer function agree well with the experimental results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.605-609
• /
• 2006

In this study, two kinds of smart accelerometers are investigated for the application of smart sensors to the structural health monitoring of infrastructures. Smart optical Fiber Bragg Grating (FBG) type and Micro-Electo-Mechanical System (MEMS) type accelerometers are selected for this study and the high sensitive ICP type accelerometer is used for the reference sensor. Small size shaking table tests were performed with 3-story shear building model using random input ground motions. The output only modal identification was carried out using stochastic subspace identification and the performances of sensors are compared in modal domain indirectly. The modal sensitivity method was applied to update the story stiffness of numerical model and the updated results were verified using the additional experiments for the same structure with additional mass.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.666-673
• /
• 2014

Finite Element Method(FEM) is the essential tools for analyzing structural and vibration problem. But common commercial program is high-priced and the usage is not easy. Hereby the authors developed FEM program by using Matlab, whose usage is very simple and whose performance is very high. For the convenience of use and calculating efficiency Component Mode Synthesis Method is adopted, which divides a structure by some sub-structures for easy handling, analyzes them by parts and analyzes the structure with encompassing Degrees of Freedom(DOF). And encompassed DOF could be restored to full DOF. To confirm the accuracy the program was applied to a flat plate, and the results were compared to experiment, and good agreements were achieved. The developed program is going to be opened to public.