• International Journal of Highway Engineering
• /
• v.7 no.1 s.23
• /
• pp.49-61
• /
• 2005

The dynamic modulus of hot mix asphalt can be determined according to the different combinations of testing temperature and loading frequency. The superposition rule is adapted to get the master curve of dynamic modulus for each hot mix asphalt. There are couple of different methods to get the shift factor which is a key for making the master curve. In this paper, Arrehnius, 2002 AASHTO, and experimental method was employed to get the master curve. Evaluation of dynamic modulus for 25mm base course of hot mix asphalt with granite aggregate and two asphalt binders(AP-3 and AP-5) was carried out. Superpave Level 1 Mix Design with gyratory compactor was adopted to determine the optimum asphalt binder content(OAC) and the measured ranges of OAC were between 4.1% and 4.4%. UTM was used for laboratory test. The dynamic modulus and phase angle were determined by testing on UTM, with 5 different testing temperature(-10, 5, 20, 40, & $55^{\circ}C$) and 5 different loading frequencies(0.05, 0.1, 1, 10, 25 Hz). Using the measured dynamic modulus and phase angle, the input parameters of Sigmoidal function equation to represent the master curve were determined and these will be adopted in FEM analysis for asphalt pavements. The shift factor and activation energy for determination of master curve were calculated.

• Membrane Journal
• /
• v.24 no.5
• /
• pp.409-415
• /
• 2014

This study is aimed to separate propylene and propane using membrane process instead of NCC(Naphtha Cracking Center) $C_3$ splitter. Membrane process is a low energy consumption and eco-friendly process while $C_3$ splitter requires high energy consumption in petrochemical processes. In this study, high performance facilitated transport membrane (FTM) is used for propylene/propane separation. FTM module was prepared on top of porous polyetherimide hollow fiber using PVP/$AgBF_4$/TCNQ. We developed simulation program predicting the membrane separation properties under operation conditions. Separation properties of FTM module for propylene and propane were obtained from the simulation program based on the pure gas permeation data. Based on these results, it is predicted that an one-stage membrane process provides 99.5% of propylene at permeate side from a binary gas mixture of 95/5 vol% $C_3H_6$ / vol% $C_3H_8$ supplied as a feed gas.

• KIPS Transactions on Software and Data Engineering
• /
• v.7 no.3
• /
• pp.113-120
• /
• 2018

In this study, we proposed a monitoring system for identifying and handling faulty sensing stream data on manufacturing equipments where low-cost sensors can be safely used. Low cost sensors will lessen the cost of implementing distributed monitoring system, but suffer from sensor noises and inaccurate sensed data. Therefore, a distributed monitoring system with low cost sensors should identify faulty signal data as either of sensor fault or machine fault, and filter out faulty signals from sensing fault. To this end, we adopted a fourier transform based diagnostic approach mixed with a weighed moving averaging method, in order to identify faulty signals. We measured how effective our approach is and found out our approach can filter out one-third faulty signals from our experimental environment. In addition, we attached wireless communication modules to reduce sensor and network installation cost. To handle massive sensor data efficiently, we employed unstructured data format with NoSQL based database.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.2 s.31
• /
• pp.171-179
• /
• 1997

The high-tension bolted joints are clamped by the axial force which approaches the yielding strength. The introduced axial force is transmitted to the connection members pass through washer. The transferred load in connections is balanced to the compressive stress of plates, axial force in bolts and the external loads. In this mechanism, the compressive stress and slip load we dominated by the effective stiffness of bolted joints and plates. In general the effective stiffness is specified to product to the effective area and elasticity modulus in connections. In this reason, the conic projection formular which is assumed that the axial force in bolts is distributed to the cone shape and that region is related to the elastic deformation mechanism in connections, was proposed. But it conclude what kind of formula is justified. Therefore in this paper, the fatigue tests are performed to the high tension bolted joints and inspected to the phase on the friction face. And using the FEM and numerical method, it is analyzed and approximated to the compressive stress distribution and its region. Moreover, it is estimated to the effective area and to the relation the friction area to the effective compressive distribution region.

• Environmental and Resource Economics Review
• /
• v.23 no.3
• /
• pp.515-551
• /
• 2014

Recently, there has been a debate as to whether bioethanol should replace some portion of gasoline for fuels in South Korea, as energy security as well as climate change issues are rising as a significant national agenda. However, a considerable amount of subsidy will be required to compensate for the higher price of bioethanol-blended gasoline. In this context, government subsidy will obtain justification only when the positive social gains from consuming bioethanol for fuels can exceed the negative social costs. Through a nation-wide choice experimental survey, we examine if South Koreans have a positive value as well as non-linear preferences on substituting bioethanol for gasoline. The results reveal that the willingness to pay for purely domestic bioethanol-blended gasoline within 10% is about 52 KRW; Koreans have concave preferences on the blending ratio of bioethanol to gasoline. The turning point of the blending ratio of bioethanol was 6.5%. Also, we found inverse U-shaped curve between income and bioethanol choice probability and the turning point of the income was calculated as 250~299million KRW. Politically conservative propensity advocates uses of bioethanol blended gasoline, but awareness on bioethanol or more weights on environmental conservation have significantly negative effects on the choice of bioethanol. However, the design of the survey questionnaire is incompatible with the RFS of Korea and assumes orthogonality among the following four interrelated attributes: (i) domestic or offshore procurement of feedstocks in the case of domestic production, (ii) domestic production or import of bioethanol, (iii) the blending ratios, and (iv) the retail price increases. In addition, the results of model estimation and of model selection test are not definite. Hence, the results in this study should not be directly applied to the design of the specifics of the Korean RFS. Hence, the results in this study require cautions in applying to the design of the Korean RFS policy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.105-112
• /
• 2018

This paper proposes a method for fabricating heatable glass using the conduction characteristics of metal thin films deposited on the surface of Low-e(Low emissivity) glass. The heating value of Low-e glass depends on the Joule heat caused by Low-e glass sheet resistance. Hence, its prediction and design are possible by measuring the sheet resistance of the material. In this study, silver electrodes were placed at 50 mm intervals on a soft Low-e glass sample with a low emissivity layer of 11 nm. This study measured the sheet resistance using a 4-point probe, predicted the power consumption and heating value of the Low-e glass, and confirmed the heating performance through fabrication and experience. There are two conventional methods for manufacturing heatable glass. One is a method of inserting nichrome heating wire into normal glass, and the other is a method of depositing a conductive transparent thin film on normal glass. The method of inserting nichrome heating wire is excellent in terms of the heating performance, but it damages the transparency of the glass. The method for depositing a conductive transparent thin film is good in terms of transparency, but its practicality is low because of its complicated process. This paper proposes a method for manufacturing heatable glass with the desired heating performance using Low-e glass, which is used mainly to improve the insulation performance of a building. That is by emitting a laser beam to the conductive metal film coated on the entire surface of the Low-e glass. The proposed method is superior in terms of transparency to the conventional method of inserting nichrome heating wire, and the manufacturing process is simpler than the method of depositing a conductive transparent thin film. In addition, the heat characteristics were compared according to the patterning of the surface thin film of the Low-e glass by an emitting laser and the laser output conditions suitable for Low-e glass.

• Korean Chemical Engineering Research
• /
• v.54 no.3
• /
• pp.380-386
• /
• 2016

In this study, we described a paper-based neuraminidase assay sensor (PNAS) which can be applied to detect the infection by influenza viruses. The PNAS was designed and manufactured to quantitatively identify the levels of neuraminidase in the sample, which is based on colorimetric analysis using the X-Neu5Ac substrate. The limit of detection of the PNAS was determined as 0.004 U/mL of neuraminidase. According to the amount of neuraminidase in human serum, the PNAS could monitor the enzyme activity with a good linearity ($R^2$ > 0.99). In addition, the initial performance of the PNAS has been maintained up to 70 days in the $4^{\circ}C$. Finally, we demonstrated whether the Michaelis-Menten kinetics is applied to the PNAS, which can show the reliability of the enzyme reactions. The kinetic studies indicated that the PNAS provides the good condition for enzyme reactions ($K_m=8.327{\times}10^{-3}M$), but they were performed on paper chip nonetheless. The paper-based neuraminidase assay sensor may be useful in a wide range of rapid and safe detection of influenza virus.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.12B
• /
• pp.2094-2108
• /
• 2000

오류를 수반하는 통신망을 통한 멀티미디어 데이터의 응용은 최근 그 수요가 급증하고 있다. 하지만 그 구현은 많은 문제점들을 야기하는데, 전송된 비디오 데이터에 발생한 오류를 처리하는 문제가 그 중 하나이다. 이는 압축된 비트열에 발생한 오류가 영상의 시-공간 방향으로 심각한 전파 현상을 수반하기 때문이다. 이러한 심각한 오류 전파를 완화하기 위해 본 논문에서는 EREC라 알려진 오류 제한 기법을 적용하고, 적용된 EREC의 오류 전파 특성을 분석하였다. 이를 통해, 압축 부호화된 하나의 기본 블록 (매크로 블록)이 복호시 오류가 생길 확률을 추정하였으며, 추정된 확률의 근사를 통해 양 끝단(전송단과 수신단)에서의 비디오 화질 열화를 예측하였다. 추정 확률의 근사는 매 기본 블록에서 발생된 비트수에 대한 그 기본 블록이 복호시 오류가 생길 확률을 간단한 1차식을 통한 선형 회귀법으로 모델링 되었으며, 따라서 간단한 방법을 통해 양 끝단의 화질 열화를 효과적으로 예측할 수 있었다. 부호화된 비트열이 전송 오류에 보다 강인하게 되도록 하기 위해, 본 논문에서 개발된 화질 열화 모델을 양자화기 선택에 적용함으로써, 새로운 최적 양자화 기법을 제시하였다. 본 논문에서 제안된 최적 양자화 기법은, 기존의 양자기 최적화 기법들과는 달리, 복호단에서의 복원 영상 화질이 주어진 비트율에서 최적이 되도록 양자화를 수행한다. H.263 비디오 압축 규격에 적용한 제안 양자화 기법의 실험 결과를 통해, 제안 기법이 매우 적은 계산상의 부하를 비용으로 객관적 화질은 물론 주관적 화질까지 크게 개선할 수 있음을 확인할 수 있었다.내었다.Lc. lacti ssp. lactis의 젖산과 초산의 생성량은 각각 0.089, 0.003과 0.189, 0.003M이었다. 따라서 corn steep liquor는 L. fermentum와 Lc. lactis ssp, lactis 의 생장을 위해 질소 또는 탄소 공급원으로서 배지에 첨가 될 수 있는 우수한 농업 부산물로 판단되었다.징하며 WLWQ에 적용되는 몇 가지 제약을 관찰하고 이를 일반적인 언어원리로 설명한다. 첫째, XP는 주어로만 해석되는데 그 이유는 XP가 목적어 혹은 부가어 등 다른 기능을 할 경우 생략 부위가 생략의 복원 가능선 원리 (the deletion-up-to recoverability principle)를 위배하기 때문이다. 둘째, WLWQ가 내용 의문문으로만 해석되는데 그 이유는 양의 공리(the maxim of quantity: Grice 1975) 때문이다. 평서문으로 해석될 경우 WP에 들어갈 부분이 XP의 자질의 부분집합에 불과하므로 명제가 아무런 정보제공을 하지 못한다. 반면 의문문 자체는 정보제공을 추구하지 않으므로 앞에서 언급한 양의 공리로부터 자유롭다. 셋째, WLWQ의 XP는 주제어 표지 ‘는/-은’을 취하나 주어표지 ‘가/-이’는 취하지 못한다(XP-는/-은 vs. XP-가/-이). 이는 IP내부 에 비공범주의 존재 여부에 따라 C의 음운형태(PF)가 시성이 정해진다는 가설로 설명하고자 했다. WLWQ에 대한 우리의 논의가 옳다면, 본 논문은 다음과 같은 이론적 함의를 기닌다. 첫째, WLWQ의 존재는 생략에 대한 두 이론 즉 LF 복사 이론과 PF 삭제 이론

• The Journal of Korean Academy of Sensory Integration
• /
• v.10 no.1
• /
• pp.21-31
• /
• 2012

Objective : This study aims to examine the Effect of the Brotherhood Group Sensory Integration intervention to Social Interaction of the Children with Pervasive Developmental Disorders. Methods : The Group Sensory Integration intervention was implemented for 8 weeks period from July to September 2011 targeting 2 children of 7~8 ages diagnosed Pervasive Developmental Disorders. For the study A-B-A' design among Single subject research design was used, while baseline A 3 phases, intervention B 16 phases, baseline A' 3 phases in total 22 phases were applied. The Quality of Social Interaction was measured through ESI(Evaluation Social interaction) during the baseline between A and A' period, and the Frequency of Social Interaction was measured under the condition that non-availability of intervention during baseline period, while during intervention period, it was measured by utilizing Interval recording method upon filming by video of 10 minutes free-play after every intervention. Results : The Quality of Social interaction indicated a statistical significance by all targeted children after intervention. Also a statistical significance was indicated in the Frequency of Social interaction as there appeared consecutively more than two of the values of baseline A average and Standard deviation band from all targeted children at the free-play implemented after each intervention of every phase. Conclusion : It could be verified that Brotherhood Group Sensory integration intervention has a positive effect to Social interaction of the Children with Pervasive Developmental Disorders. Therefore, the Brotherhood Group Sensory integration intervention can be effectively applicable as being a therapy to improve Social interaction toward Children with Pervasive Developmental Disorders at the clinic.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.486-496
• /
• 2018

This study was conducted to confirm an effect of span length on bending properties of larch dimensional lumber in the four point bending test. The size of specimen in this study was 38 (width) ${\times}$ 89 (depth) ${\times}$ 3,600 (length) $mm^3$, and average air-dry density and moisture content of the specimens was $543.5kg/m^3$ and 10.5%, respectively. Visually graded No. 1 dimensional lumbers of 248 were divided by two groups to compare modulus of rupture (MOR) and modulus of elasticity (MOE). One group was tested in the four point bending test with span length of 1,650 mm, and other was tested with span length of 3,000 mm. While MOE was not different according to span length in 5% significance level, MOR was different in accordance with span lengths and was in inverse proportion to change of span length. Fifth percentiles of MOR in span length of 1,650 and 3,000 mm were 28.65 and 25.70 MPa, respectively. It was confirmed that the difference between MORs in each case increased as normalized rank increased. This is because of size effect in Weibull weakest link failure theory. Therefore, KS F 2150, in which there is only regulation about span to depth ratio of 15 or more, is needed to be revised to contain a method considering size effect for MOR. From the method, various results of bending test with different size of lumber could be used to determine design value of lumber.