• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.16 no.3
• /
• pp.1-6
• /
• 2008

The stalling speed flight test of light airplane, ChangGong-91, was performed to acquire the certification. With power-off engine condition, the wings level stall flight tests were conducted at the aircraft configuration of various flap angle - clean, 20degree, and full flap, respectively. They were performed considering with the combination of the maximum and minimum test weight, and forward and afterward center of gravity. The stalling speeds and the minimum speeds of light airplane were determined from the results of flight test. Also, the appropriateness of stall warning speeds are evaluated through the flight test measures. The airplane is recoverable only with pitch control and engine throttle from stall state without exceptional operation.

• Plant Journal
• /
• v.8 no.4
• /
• pp.34-39
• /
• 2012

This study presents how low quality coal combustion affects the desulfurizer draft system by correlating of draft loss in a coal-fired thermal power plant and predicts the stall occurrence time of a booster fan. In case of low quality coal, a lot of coal is needed to generate equivalent output power, thereby the rating of increasing draft loss was faster than designed amount of coal. We surely confirmed that draft loss affects the specific energy of a booster fan strongly. On this basis, it is possible to predict the occurring time of stall for a booster fan from current operation specific energy to stall limit specific energy. This study suggests increasing speed of draft loss in each caloric value and the impact of specific energy at a booster fan, it expects to help safe operating in a thermal power plant.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.65-72
• /
• 2012

Numerical simulations were performed to study the stall characteristics of turboprop aircraft. Stall characteristics were qualitatively investigated using the computational results of various configurations based on the combinations of propeller and high lift device. For the analysis of stall characteristics, three-dimensional Navier-Stokes solver with Spalart-Allmaras turbulence model was used and the relative motion between propeller and wing was simulated using sliding mesh technique. For the cruise configurations, major flow separation was occurred at the fuselage/wing fairing and the separation was reduced under propeller slipstream condition. For the high lift device configuration without propeller, major flow separation was occurred at the outboard side of nacelle. With rotating propeller, early stall onset due to low relative velocity and high effective angle of attack was observed on the outboard wing section. Regarding rotating direction of propeller, inboard-down direction was preferred due to the stall delay effect of propeller slipstream.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.625-630
• /
• 2014

연료전지의 성능을 결정짓는 가장 중요한 변수 중의 하나는 각 스택의 채널에 얼마나 균일하게 연료를 공급할 수 있느냐이다. 본 연구에서는 네 가지의 모델을 사용하여 연료전지 매니폴드 형상에 따른 최적 설계를 수행하였다. 위 네 가지 모델은 각기 다른 기하학적 형상을 가지며 Edison CFD를 이용하여 형상 내의 유동을 비교하였다. 초기 모델에서는, 입구부에서 매니폴드로 유입되는 유동의 확산이 잘 일어나지 않아 각 채널의 질량유량이 불균일한 분포를 보였으며 특히 속도가 빠른 중심 영역의 채널에 많은 연료가 유입되었다. 이를 위한 디퓨져 모델링이 제안되었으며 실속이 최소한도로 발생할 때 채널당 질량유량이 가장 균일하다고 가정하였다. 이를 위해 다양한 디퓨져 각을 가진 모델을 사용했고, 이론상으로 실속이 발생하지 않는 형상에서 가장 균일한 분포를 보임을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.2
• /
• pp.153-161
• /
• 1998

This study describes the results of the analysis of measured rotating stall signal in a centrifugal compressor with vaneless diffuser. Unsteady flow and rotating stall in vaneless diffuser were investigated by measuring of unsteady velocity fluctuation using hot-wire anemometer. Experiments were carried out in several impeller rotating speeds, at different radius ratios. Single hot -wire was used to study the characteristics of rotating stall. As a result, the abrupt rotating stall was detected at all measured impeller rotating speeds and the several flow coefficients which are less than 0.16. The number of the stall cell was one at all measured rotational speeds, and the rotating direction was the same as that of the impeller. As the flow rate decreased, the profile of the phase averaged radial velocity component with time changed from a sawtooth to a sine wave.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.1017-1025
• /
• 2008

The air data system(ADS) was developed for unmanned aerial vehicle(UAV) in this paper. Generally, the ADS helps flight control computer(FCC) to control the UAV above the stall speed and to hold the given altitude. The accurate measurement of airspeed and altitude of UAV is important because it indicates a flight performance and assures a safe flight. The ADS consists of MEMS pressure sensors, a lowpass filter, a micro controller unit and a pitot-tube. The ADS errors were reduced by pressure and temperature compensation of MEMS sensors. Finally, the altitude and airspeed data of the ADS was compared with GPS data in the flight test.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1247-1254
• /
• 1998

The vaneless diffusers are widely used in industrial centrifugal compressors which are required to operate within a wide flow range. When very high pressure gases are handled by centrifugal compressor. rotating stall is a serious problem because of the occurance of large aerodynamic exciting forces. Rotating stall mostly often occurs in the impellers but it can occur in vaneless diffusers as well. In this experimental study, the rotating stall in vaneless diffuser with radial type centrifugal impeller was measured by changing the flow rate with I-type, X-type hotwire. As the result, it was cleared which type of rotating stall of the impeller stall would occur and how many stall cells would appear relating with the flow rate. As the flow rate reduced, the propagation speed of rotating stall was reduced. But the stall cell number unchanged with respect to the flow rate.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.3 no.1
• /
• pp.145-159
• /
• 1995

정확한 고도, 속도의 측정은 항공기의 효율적인 운영과 안전에 필수적이다. 정확한 고도의 측정은 지형 장애물의 회피와 항로상에서 최저 수직 고도 분리를 유지하기 위해 절대적으로 필요하다. 또한 정확한 속도의 측정은 저속(실속상태)에서 조종상실을 피하고 고속에서 항공기의 구조적 한계와 공기 역학적 한계의 초과를 방지한다. 따라서 비행시험을 통하여 고도와 속도를 정확히 보정해줌으로써 비행안전과 재산상의 손실을 막을 수 있다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.8
• /
• pp.649-656
• /
• 2013

High-lift devices have a major influence on takeoff, landing and stall performance of an aircraft. Therefore, a slotted flap design optimization process is proposed in this paper to obtain the most effective flap configuration from supported 2D flap configuration. Flap deflection, Gap and Overlap are considered as main contributors to flap lift increment. ANSYS Fluent 13.0.0$^{(R)}$ is used as aerodynamic analysis software that provides accurate solution at given flight conditions. Optimum configuration is obtained by Sequential Quadratic Programing (SQP) algorithm. Performance of the aircraft with optimized flap is estimated using Aircraft Design Synthesis Program (ADSP), the in-house performance analysis code. Obtained parameters such as takeoff, landing distance and stall speed met KAS-VLA airworthiness requirements.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.1
• /
• pp.81-93
• /
• 1993

창공-91의 비행 시험의 목적은 성능 측정과 비행 특성의 확인이며 교통부의 기준은 주로 비행기의 운항에 따르는 안정성에 주안점을 두고 있다. 비행 시험으로 실속 속도와 이착륙 성능 그리고 상승 성능을 측정하여 비행 교범에 수록하였고, 안정성과 조종성의 적절함을 판단하였다. 창공-91 A2기의 비행 시험에 소요된 비행 시간은 81. 5 시간이다. (창공-91 $A_1$기 : 52.8시간)