• Journal of the Korean Applied Science and Technology
• /
• v.36 no.4
• /
• pp.1410-1419
• /
• 2019

In this research, it is to find a method that frost does not form on the outdoor unit to develop a heat pump capable of heating in cold regions. For this reason, we produced an incubator capable of creating an environment of -25℃, and constructed an experimental apparatus so that experiments in the room were possible. However, it is necessary to grasp the characteristics of the air reaching the front of the heat pump outdoor unit installed in the experimental apparatus, and flow analysis was performed using ANSYS CFX, which is general-purpose software. As a result, the flow velocity of the air reaching the front of the outdoor unit in the outdoor unit chamber in the entire region of the simulation conditions (5.0 to 7.5 m/s) has many differences in the upper and lower portions, resulting in a natural state. It turned out that the condition can not be satisfied. Therefore, it is determined that it is necessary to additionally install a frequency divider at the front of the outdoor unit to make the flow velocity constant.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.6
• /
• pp.1312-1317
• /
• 2013

Pseudolite is a contraction of the term "pseudo-satellite", used to refer to something that is not a satellite which performs a function commonly in the domain of satellites. Pseudolite are most often small transceivers that are used to create a local, ground-based GPS alternative. Pseudo-range measurement of pseudolite has around 300m range error, when time synchronization error of $1{\mu}sec$ occurs. Therefore the time synchronization methods play an important part in navigation augmentation using pseudolite. This paper proposes three clock synchronization methods that are installation method of pseudolite station, method using KRISS-UTC and method using PRN code phase difference for pseudolite. The simulation platform structure is presented for evaluating proposed clock synchronization performance.

• Journal of Wetlands Research
• /
• v.19 no.4
• /
• pp.484-490
• /
• 2017

In order to examine flow characteristics according to the shape of the meandering low flow channel in the compound cross section typed straight channel, we assumed the representative channel type in Korea and confirmed the validity of the 3D numerical simulation by carrying out the hydraulic model. Based on this study, numerical simulations were also conducted on other types of river channel. As a result of the numerical model test (using the velocity value measured by the water depth observation from the hydraulic model test), it was confirmed that the numerical simulation results are in good agreement with the numerical simulation results. As a result of analyzing the flow field according to the changes in the shape of the low flow channel, it was confirmed that the secondary flow examined in the previous studies occurred. Also, it was confirmed that the maximum flow velocity point moves according to the expansion cross sectional area of flow in high flow plain. Ultimately, it is thought that it is necessary to understand the position of the water impingement (which is an important factor in river design) and the extent of the impact because the change of the channel width affects the flow.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.101-104
• /
• 2015

In this paper, a flight techniques many quadcopters which can be configured flexibly squadron according to the situation in wireless sensor networks is suggested. In previous studies, aircrafts fly only as part of a prescribed form and know the distance between the aircraft by sensor was able to maintain the fleet. Also, the problem occurs that between the aircraft distance is not constant. In this paper, proposes an algorithm that the context of the formation fly using the current position of the quadcopter through a virtual map is based on the relative coordinates without being affected by Indoor, outdoor and obstacles. Proposed algorithm is Leader-Follower Technique that the method of determinin the shape of the squadron to the down command to the sub-quadcopter using the wireless network by the main quadcopter to determine a given situation. As simulation result, the proposed algorithm was confirmed that formation flight efficient in sensing the all conditions as compared to the conventional method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.4
• /
• pp.315-325
• /
• 2014

In ubiquitous environment, User's location information is very important to serve personalized service to user. Previous works consider only User's locations in the big buildings and assume APs are fixed. Normal home environment, However, is consists of small spaces. And the state of APs is highly fluid. Previous research has focused on indoor localization in the building where has stationary AP environment. However, in this paper, we propose as User's Location Predicting System that finds out a space where a user is located based on Wi-Fi Fingerprint approach in home environments. The results that conducted real home environments are using the system show more than 80% accuracy.

• Economic and Environmental Geology
• /
• v.47 no.2
• /
• pp.97-105
• /
• 2014

Peperite exposed along the Dajeonsa basalt in Mt.Juwang, Cheongsong emerged as a consequence of the simultaneity of volcano-sedimentary sequences. This study aims to classify peperites as morphological characteristics and infer the formation process by the field investigation, image analysis, X-Ray Diffractometer and polarization microscope for the magma-sediment interaction mechanism and paleoenvironment. As a result of the field investigation globular(fluidal) peperite is the representative feature at the bottom of Dajeonsa basalt, sub-angular peperite at the middle and irregular peperite at the top. Peperite domains range from sheet and pod or feeder conduit. Although the study that the morphologies of peperite are controled by the sorts of sediment and lava or magma has tended to center around the peperite, the study addresses not single mechanism but the multi-stage mechanism because Mt.juwang peperite, under the same conditions, varies in shapes and sizes and also the ratio of sediments that show the most change of the peperite affects to the formation of peperite.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.6
• /
• pp.870-879
• /
• 2000

An experimental investigation is conducted to improve a slot film cooling system which can be used for the cooling of gas turbine combustor liner. The tangential slots are constructed of discrete holes with different injection types which are the parallel, vertical, and combined to the slot lip. The investigation is focused on the coolant supply systems of normal-, parallel-, and counter-flow paths to the mainstream direction. A naphthalene sublimation technique has been employed to measure the local heat/mass transfer coefficients in a slot with various injection types and coolant feeding directions. The velocity distributions at the exit of slot lip for the parallel and vertical injection types are fairly uniform with mild periodical patterns with respect to the hole positions. However, the combined injection type increases the nonuniformity of flow distribution with the period equaling twice that of hole-to-hole pitch due to splitting and merging of the ejected flows. The secondary flow at the lip exit has uniform velocity distributions for the parallel and vertical injection types, which are similar to the results of a two-dimensional slot injection. In the results of local heat/mass transfer coefficient, the best cooling performance inside the slot is obtained with the vertical injection type among the three different injection types due to the effect of jet impingement. The lateral distributions of Sh with the parallel- and counter-flow paths are more uniform than the normal flow path. The averaged Sh with the injection holes are $2{\sim}5$ times higher than that of a smooth two-dimensional slot path.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.67-74
• /
• 2013

A jet in a crossflow (JICF) has been extensively studied because of its wide applications in technological systems, including fuel injection into a ram-combustor. However, in the case of insufficient mixing performance of the liquid jet into the crossflow, the flame in a ram-combustor is unstable. In this study, the nonuniform flame and combustion instabilities due to lack of mixing performance were experimentally investigated. By performing correlations to predict the penetration height and break-up point, the spray and mixing characteristics of JICF have been studied. In particular, the improved correlations of penetration height are proposed in two distinctive domains depending on the X/d location of the crossflow.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.38-43
• /
• 2007

The aim of this paper is to investigate the change of pressure differential and smoke propagation characteristics in the elevator lobby with the resident's evacuation scenarios using fire modelling technique. The results showed absolute pressures in the fire room and elevator lobby can significantly increase to cause fire door to the stairway unclosed once it is open. This is due to constant pressure differentials, the increasing reference pressure of fire lobby and pressure leak from elevator lobby to fire lobby. Smoke exhaust mechanism was needed to prevent the continuous pressure rise in the living room. Over 200 Pa was expected upon closing the door during pressurization, which provide difficulties in opening the door for next refugee. Opening both fire door and entrance door may induce smoke flow from fire room to elevator lobby and stairway.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.12
• /
• pp.588-593
• /
• 2014

To maintain a negative pressure, the supply, exhaust airvolume are adjusted by setting volume damper and the infiltration through leakage area of the door between rooms in biosafety laboratory. Multizone simulation is useful way to predict room pressure, supply and exhaust air volume. But in a particular room, local change such as airflow and contaminants concentration distribution can not be evaluated unfortunately. Through this study, a coupled multizone and CFD simulation was performed, indoor air flow and local contaminants concentration distribution in a particular room of BSL lab are predicted. The results show that all zones of BSL lab are well ventilated by unidirectional flow without local stagnation. In addition, in case that unexpected biohazard is occured in BSL lab, multizone simulation results about the spread of pollutants along movement of the occupant also show that contaminants concentration is removing totally without the spread of the outside. In conclusion, a coupled multizone and CFD simulation can be applied to interpret differential pressure in room and local change of physical quantity in a particular room such as airflow and Influenza A contaminants concentration distribution. This simulation method is useful to enhance the reliability and accuracy of biosafety laboratory design.