• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.237-245
• /
• 2020

In decades, active sonar, which transmits signals and detects incident signals reflected by underwater targets, has been significantly studied since passive sonar in Anti-Submarine Warfare (ASW) detection performance becomes lowered, as underwater threats become their radiated noise reduced. In general, active sonar using Hull-Mounted Sonar (HMS) adjusts vertical tilt (depression) and sequentially transmits multiple Linear Frequency Modulation (LFM) subpulses which have non-overlapped bands, i. e. 1 kHz ~ 2 kHz, 2 kHz ~ 3 kHz, in order to reduce shadow zones. Recently, however, Generalized SFM (GSFM), which is generalized form of SFM, is proposed, and it is confirmed that subpulses of GSFM have orthogonality among each other depending on setting of GSFM parameters. Hence, in this paper, we applied GSFM to active target detection using HMS to improve the performance by the signal processing gain obtained from enlarged bandwidths of GSFM subpulses compared to those of LFM subpulses. Through simulation, we verified that when the number of subpulses is three, the matched filter gain of GSFM is approximately 5 dB higher than that of LFM.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.3
• /
• pp.213-221
• /
• 2009

The time reversal mirror (TRM) method for underwater communications has been developed to improve transmission performance with low complexity. However, digital communication parameters for TRM have not been researched deeply. This paper demonstrates that the TRM scheme obtains spatial diversity gain similar to multiple antennas, and proposes design methodologies of symbol interval, frame duration and transmission protocol for time reversal mirror transmission. Simulation results show that spatial diversity gain is achieved and the effect of ISI decreases as the number of transducer increases.

• 전자공학회논문지 IE
• /
• v.48 no.3
• /
• pp.10-15
• /
• 2011

In the case of designing an acoustic transducer for high power application, we usually aim to transfer the source electric energy to the output acoustic energy as large as possible. For this purpose, we should match the impedance of the power amplifier to the impedance combined with the acoustic transducer impedance and the radiation impedance. Especially if we have electrical source with almost zero impedance, we need improve the power factor of the acoustic transducer in the load. In this paper, we propose a broad band impedance matching method by the improvement of power factor, which applies ABCD matrix.

• Korean Journal of Optics and Photonics
• /
• v.30 no.2
• /
• pp.48-58
• /
• 2019

We investigate the signal-to-noise ratios (SNRs) of time-domain (i.e. pulsed illumination) and frequency-domain (i.e. chirped illumination) photoacoustic signals measured by a spherically focused ultrasound transducer for spherical absorbers. The simulation results show that the time-domain photoacoustic SNR is higher than that of frequency-domain photoacoustic signals, as reported in the previous literature. We understand the reason for this SNR gap between the two measurement modes by analyzing photoacoustic-signal spectra, considering the incident beam energy controlled by the maximum permissible exposure. As the result of this approach, we find that filtering off the DC term in the chirped signal's spectrum improves frequency-domain photoacoustic SNRs by up to approximately 5 dB. In particular, it is observed that photoacoustic SNRs are highly sensitive to an upper-frequency value of frequency filtering functions, and the optimal upper-frequency values maximizing the SNR are different in time- and frequency-domain photoacoustic measurements.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.1
• /
• pp.41-48
• /
• 2003

In this paper, a new equivalent circuit for a defected ground structure(DGS) is proposed and adapted to design of a power amplifier for performance improvement. The DGS equivalent circuit presented in this paper consists of parallel LC resonator and parallel capacitance to describe the fringing fields due to the etched defects on the metallic ground plane, and also is used to optimize the matching circuit of a power amplifier. A previous research has also used a DGS for harmonic rejection and efficiency improvement of a power amplifier(1), however, there was no exact equivalent circuit analysis. In this paper, we suggest a novel design method and show the performance improvement of a class AB power amplifier by using the equivalent circuit of a DGS applied to output matching circuit. The design method presented in this paper can provide very accurate design results to satisfy the optimum load condition and the desirable harmonic rejection, simultaneously. As a design example, we have designed a 20W power amplifier with and without circuit simulation of DGS, and compared the measurement results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.15-23
• /
• 2007

A simple six-port direct conversion QPSK receiver which is made up of a six-port phase correlator, a signal power detector, and I/Q channel signal de-modulator is designed and implemented in this paper. The output phase signals of six-port phase correlator are also analysed. On the basis of $90^{\circ}C$ phase relation among the six-port phase correlator output signals, the QPSK de-modulation circuit is designed by a simple circuit. The six-port phase correlator is made up of $90^{\circ}$ hybrid branch line and power detector. The six-port phase correlator, which is designed in frequency range of 11.7 to 12.0 GHz, gets the phase error characteristics less than $5^{\circ}$. By considering matching network and amplitude balance in the designed fiequency range, the designed six-port direct conversion QPSK receiver demodulates the I and Q signals with performance less than $5^{\circ}$ phase error.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.11
• /
• pp.28-33
• /
• 2002

In this paper, the impedance-tuned monopole microstrip antenna designed for PCS is analyzed using finite difference time domain(FDTD) method. The perfectly matched layer(PML) absorbing material condition proposed by Berenger is used for the truncation of finite difference time domain lattice. A Gaussian pulse is selected as an excitation signal and a resistive voltage source model is used to reduce the error caused by the reflection waves. The FDTD method is inherently a near field technique. Therefore, the near field to far field transformation is need to compute far field antenna parameters such as radiation patterns and gain. The near field to far field transformation can be done both in the time domain and the frequency domain. We use the frequency domain transformation to compute the far field radiation patterns at single frequency. All the numerical results obtained by the FDTD method are compared with simulation results using the HFSS software. Good agreements are obtained in all cases.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.135-140
• /
• 2008

In this paper, the spiral antenna with the center frequencies of 315MHz, 433MHz, and 447MHz for RKE system of a vehicle is designed on PCB. The antenna is microstrip line-fed, and applied PIFA concept near the feeding part to easily tune center frequency and input impedance. The PIFA-type spiral antenna with the size of $30mm{\times}20mm$ is designed on printed PCB by considering the effect of circuits and components on PCB, ECU case and vehicle body. Also chip inductor inserted dual-band spiral antenna of 315MHz and 447MHz is designed. We found that the antenna designed on PCB satisfied the antenna specifications through measurement and field test.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.919-923
• /
• 2003

In this paper, a double-sided planar balun using Microstrip-to-CPW coupled structure is fabricated and measured. The measured amplitude and phase imbalance are, respectively, less than 0.2 dB and 2.1$^{\circ}$ in a wide frequency range from 2.44 GHz to 4.33 GHz. It is expected that the proposed balun can improved the performance of balanced mixer, amplifier and feeding network of antennas. Also, it can be used in many microwave multilayer structures due to its structural characteristics.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.13-22
• /
• 2001

This paper presents three dimensional structure of RF packages and the improvement effect of its electrical characteristics when implementing RF transceivers. We divided RF modules into several subunits following each subunit function based on the partitioning algorithm which suggests a method of three dimension stacking interconnection, PAA(pad area array) interconnection and stacking of three dimensional RF package structures. 224MHz ITS(Intelligent Transportation System) RF module subdivided into subunits of functional blocks of a receiver(RX), a transmitter(TX), a phase locked loop(PLL) and power(PWR) unit, simultaneously meeting the requirements of impedance characteristic and system stability. Each sub­functional unit has its own frequency region of 224MHz, 21.4MHz, and 450KHz~DC. The signal gain of receiver and transmitter unit showed 18.9㏈, 23.9㏈. PLL and PWR modules also provided stable phase locking, constant voltages which agree with design specifications and maximize their characteristics. The RF module of three dimension stacking structure showed $48cm^3$, 76.9％ reduction in volume and 4.8cm, 28.4％ in net length, 41.8$^{\circ}C$, 37% in maximum operating temperature, respectively. We have found that three dimensional PAA package structure is able to produce high speed, high density, low power characteristics and to improve its functional characteristics by subdividing RF modules according to the subunit function and the operating frequency, and the features of physical volume, electrical characteristics, and thermal conditions compared to two dimensional RF circuit modules.