• Korean Journal of Organic Agriculture
• /
• v.26 no.2
• /
• pp.281-296
• /
• 2018

This study was conducted to evaluate the effect of different processing of rice on rumen fermentation in in vitro and in situ experiments. Different processing treatments (extruding, roasting, and steaming) were used in this study and all treatments were ground through a cyclone mill (Foss, Hillerød, Denmark) fitted with a 1 mm screen. Non-treated rice was considered to a control substrate. Then, all treatments were used in in vitro and in situ experiments. Total gas production and dry matter digestibility in control were lower than any other treatment at all incubation times (P<0.01). The lowest ammonia nitrogen ($NH_3-N$) concentration was observed in control among treatments at 6, 12, and 24 h incubation (P<0.01). Extruding had a highest total volatile fatty acids (VFA) concentration at 6, 12 h incubation (P<0.01) and Steaming exhibited a highest total VFA at 24 h (P<0.01). The lowest total VFA concentration was observed in control at 6, 12, and 24 h (P<0.01). In an in situ, The highest value of soluble fraction, degradation rates, effective degradability was observed in extruding (P<0.01). It was considered that feed processing increased dry matter digestibility, total VFA concentration, and decreased pH as well as $NH_3-N$ concentration indicating that processing may increase nutrient degradation of rice in the rumen.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.4 s.71
• /
• pp.407-414
• /
• 2004

Bridges in common use are expected to have more varieties of load in their connected members and bolts than in construction. Faults in connection members or bolts occur so often according to the time flow. One of the purposes of this study is to find out the behavior and structural features of high-tension bolted joints with faults that are very difficult and cost much to find out through experimentation with finite element analysis. Another purpose of this study is to provide sufficient data, estimated experimental results, and the scheme of the test plate for an economical experimental study in the future. Surveys of bridges with a variety of faults and statistical classifications of their faults were performed, as was a finite element analysis of the internal stress and the sliding behavior of standard and defective bridge models. The finite element analysis of the internal stress was performed according to the interval of the bolt, the thickness of the plate, the distance of the edge, the diameter of the bolt, and the expansion of the construction. Furthermore, the analysis explained the sliding behavior of high-tension bolt joints and showed the geometric non-linear against the large deformation, and the boundary non-linear against the non-linear in the contact surface, including the material non-linear, to best explain the exceeding of the yield stress by sliding. A normally bolted high-tension bolt joint and deduction of bolt tension were also analyzed with the finite element analysis of bridge-sliding behavior.

• Journal of Korean Society of Transportation
• /
• v.26 no.2
• /
• pp.7-15
• /
• 2008

New Car Assessment Program(NCAP) provides consumers with vehicle safety information, primarily front and side crash rating results, and more recently rollover ratings, to aid consumers in their vehicle purchase decisions. NCAP is a system to improve driver and passenger safety by providing market incentives for vehicle manufacturers to voluntarily design their vehicles to better protect drivers and passengers in a crash and be less susceptible to rollover, rather than by regulatory directives. NCAP have been performed since 1999 in Korea by the government in order to reduce fatalities and injuries caused by traffic accidents. Although as the number of vehicles models increases, more vehicle models are required to be test and NCAP is evaluated as a valuable system for vehicle safety, the expansion of the system is slow. It looks like that the benefit of NCAP quantitatively was not verified. In this study, based on the idea that the benefit of the NCAP is defined as the decrease of traffic accident severity by improving vehicle safety, a methodology to analyze the effectiveness of NCAP quantitatively in terms of traffic safety was developed. According to the developed methodology, the reduced numbers of fatalities and injuries were 1.51 and 466 in 2005.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.48 no.3
• /
• pp.200-204
• /
• 2003

This study was conducted to develop a technology for raising seedlings hydroponically using the bed in which the seedlings grew in nutrient solution without soil. In order to establish the optimum EC value of nutrient solution, six initial EC values (1, 2, 3, 4, 5 dS/m and control) of Yoshida's hydroponic solution were examined. Seedling height and dry weight increased with increasing below EC up to 3.0 dS/m, but showed no significant increase at higher than EC 3.0 dS/m. Nutrient solution with initial EC of 3.0 dS/m was good to be dropped down nearly to 1 dS/m after 15-day seedling culture. But those with initial EC of 4.0 and 5.0 dS/m were judged not appropriate because of high EC value in waste nutrient solution. Utilization efficiency of minerals of nutrient solution and rice endosperm was higher on the whole at initial EC of 2.0-3.0 dS/m. Considering seedling growth and utilization efficiency of supplied nutrient solution, initial EC is judged to be suitable at 3.0 dS/m.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.89-89
• /
• 2012

선행 연구에서는 m-Aramid와 p-Aramid의 Ring 방적사/Core 방적사 조건에 따른 방적사 물성에 대해서 연구하였는데, Ring 방적사의 혼용율, 스핀들 속도에 따른 물성 변화, Core 방적사의 공정특성에 따른 방적성, 피복성에 대해 연구를 하였다. 그 결과 Ring 방적사의 경우 m-Aramid의 혼용율이 증가할수록 사 강도는 증가하는 경향을 확인할 수 있었고, 스핀들 속도가 증가함에 따라서 불균제도 및 사결점이 다소 증가하였다. Core 방적사의 경우 Core에 p-Aramid를 사용했을 때 방적성과 피복성은 양호 하였지만, 강한 p-Aramid에 의해 톱 롤러코트의 마모가 되는 경향을 볼 수 있었다. 본 연구에서는 Ring 방적사/Core 방적사에 대해 좀더 구체적인 제조공정조건에 의한 물성 변화를 알아보았고, 좀더 다양한 섬유소재를 적용해서 제조하였다. Ring 방적사의 경우 p-Aramid 혼용율에 따른 실험을 하였는데, m-Aramid에 대한 p-Aramid의 혼용율을 0%, 5%, 10%, 20% 로 하여 Ne30을 제조하였으며, Core 방적사는 Core를 p-Aramid 200D로 하고 Sheath를 Cotton으로 하여 Core 공급속도비 (1.06, 1.10, 1.14), 연계수(T/M, 3.8, 4.0, 4.2), Sheath/Core 혼섬율(70/30, 60/40, 50/50)에 따라 제조하였다. 추가로 Core 방적사는 Sheath에 Cotton 대신 FR-Rayon과 선염 Cotton을 사용하여 각각 Sheath/Core 혼섬율 70/30의 비율로 방적사를 제조하여 다양한 소재에 따른 방적사의 물성을 측정하였다. 제조된 시험 원사들의 측정 물성은 번수(Ne), 균제도(U%), 사결점(IPI), 강력(cN), 신도(%), 비강도(cN/Tex) 등이며, 편직을 통해 편성물의 외관을 확인하였다. Ring 방적사의 경우 p-Aramid의 혼용율이 증가할수록 강도는 완만하게 증가한 반면, 신도는 급격하게 감소하였다. Cotton Core 방적사의 경우는 공급속도비가 높아질수록 균제도가 높아지는 것을 볼수 있었고, Core 공급속도비가 높아질수록 외관상 피복도는 높아진 것을 볼 수 있었다. 이렇게 연구된 Aramid 소재를 이용한 방적사 제조 공정조건변화에 따른 물성 및 피복도 결과는 기존 방적업체에서 Aramid를 이용한 방적사 제조시에 공정조건을 확보하는데 도움이 될 것이라 생각되며, 방적사 시제품 생산시에 발생할 수 있는 시행착오를 줄임으로써 시제품 제조를 위한 생산비용의 Loss를 절감할 수 있을 것으로 예상된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.570-576
• /
• 2018

In reinforced concrete structures, the joints of ordinary rebars are usually lap joints, which are bound by binding wires with rebars, and mechanical joints by couplers. In domestic design standards (concrete design code), welded lap joints are restricted for ordinary rebars, but overseas standards allow welded lap joints of ordinary rebars through pre-heating. This study investigated the domestic and international standards/criteria and evaluated the fracture strength by performing the tensile test on the lap welded joint of SD400 grade rebars, which is used the most in the construction sites. The weld length of the specimen for weld lap joints is based on the minimum weld length (8d) given in the KS standard (KS B ISO 17660-1). According to AWS D1.4, the preheating temperature was set to $150^{\circ}C$ for D19 and below, and $260^{\circ}C$ for D22 and above. In the test results, the tensile strength of rebars with welded lap joints exceeded the required strength (125% of the yield strength) according to the concrete design code. To analyze the effect of preheating, the tensile strength of the welded rebars after preheating was not significantly different from that of the welded rebars without preheating. The carbon equivalent content (Ceq) of the rebars used in the test was 0.45% or less. Under AWS D1.4, no preheating is required if the carbon equivalent is less than 0.45%. All specimens with a welded lap length of 8d failed by a bar fracture. The effect of preheating was confirmed to be insignificant due to the low carbon equivalent of the rebar.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.7
• /
• pp.73-83
• /
• 2017

This study was conducted to evaluate the chemical composition, digestibility, and energy value of 15 non-conventional feeds produced in South Korea as ruminant feeds. Three Hanwoo steers (body weight, $520{\pm}20.20kg$) fitted with a permanent rumen cannula and duodenal cannula were housed individually in tie-stall barns, followed by a 14-day adaptation period and 3-day experimental period. Chemical composition analysis, in situ nylon bag, and mobile bag technique were used as experiments. As a result of the chemical composition analysis offeeds, crude protein (CP) contentsofmalt meal, perilla meal, soy sauce cake, and soymilk residue were greater than 30%. As a result of the degradability characteristics analysis of feeds using an in situ nylon bag, rumen undegraded protein (RUP) contents of beet pulp, brewer's grain, coffee meal, malt meal, milo bran, perilla meal, ramen residue, and soymilk residue were greater than 50%. Analysis of total digestible nutrient (TDN) values of feeds using an in situ mobile bag showed that TDN values of beet pulp, brewer's grain, makgeolli residue, milo bran, perilla meal, ramen residue, rice bran, soy sauce cake, soybean curd cake, soymilk residue, and wheat bran weregreater than 50%. In summary, these non-conventional feeds have high potential value as good feed resources to replace formulated feeds or roughage. Therefore, the chemical composition, digestibility, and energy value of non-conventional feeds obtained from this study can be used as base data for the manufacture of ruminant total mixed ration (TMR) with improved feed efficiency, reduced feed costs, and reduction of environmental pollution.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.603-608
• /
• 2018

Although the voltage-applied discharge method is most widely used in the semiconductor and display industries, periodic management costs are incurred because the method causes defects due to the absorption of ambient fine dust and causes emitter tip contamination due to the discharge. The emitter tip contamination problem is caused by the accumulation of fine particles in ambient air due to the corona discharge of the ionizer. Fuzzy ball generation accelerates the wear of the emitter tip and deteriorates the performance of the ionizer. Although a mechanical cleaning method using a manual brush or an automatic brush is effective for contaminant removal, it requires management of additional mechanical parts by the user. In some cases, contaminants accumulated in the emitter may be transferred to the wafer or product. In order to solve this problem, we developed an ionizer for a clean environment that can remove the pencil-type emitter tip and directly ionize the surrounding gas molecules using the tungsten wire located inside the ion tank. As a result of testing and certification by the Korea Institute of Machinery and Materials, the average concentration was $0.7572particles/ft^3$, the decay time was less than two seconds, and the ion valance was 7.6 V, which is satisfactory.

• Environmental and Resource Economics Review
• /
• v.16 no.1
• /
• pp.129-169
• /
• 2007

The purpose of this study is to experiment and simulate the newly-updated Second Generation Model for Korea (SGM-Korea). With the updated model, we tried to simulate effect of carbon tax on $CO_2$ emissions and other macroeconomic variables for Korea. The baseline data are compared with projected profiles by various scenarios to evaluate its performance. Our contribution in this study is to having up-graded the model from its earlier version by building new hybrid input-output table based on 2000 input-output and energy balanced tables. According to our estimation, total $CO_2$ emission in Korea has already increased in 2000 to about 1.86 times the 1990 figure. The level of carbon tax required for the current level of $CO_2$ emission to be reduced to the 1995 or 2000 level seems to be too high for Korean economy to bear. It is possible to find a reasonable level of carbon tax, however, if it can combine it with improvement of energy efficiency at the rate of 0.5% to 1% per year. For Korea to meet its obligation to reduce $CO_2$ emissions, therefore, it is imperative for her to improve energy efficiency as well as to develop alternative energy source reducing its dependence on fossil fuel.

• Korean Journal of Remote Sensing
• /
• v.33 no.2
• /
• pp.231-242
• /
• 2017

Monitoring of facilities such as roads, dams and bridges is important for their long-term sustainable usage. It has usually suffered with safety and cost problems, which makes more frequent monitoring difficult. As an efficient and economicalsolution to these problems, one may consider the use of smartphone to capture the status of the facilities. To derive quantitative analysis results with the smartphone images for facility monitoring, one should first rectify the images in a way as automatic and economical as possible. In thisstudy, we propose such a rectification method, which rectifiessmartphone images acquired from arbitrary locations based on reference images.In the proposed method, we determine the camera extrinsic parameters of each smartphone images using the reference imagesrather than ground control points, and project the image to the target surface of the facility based on the determined camera parameters. The method were applied to test data acquired from a small dam toward water-area facility monitoring. The experimental results showed that the camera extrinsic parameters were determined with the accuracy of 5 cm and $0.28^{\circ}$ in the position and attitude. The accuracy of the distance measured from the rectified image was evaluated to 10 cm. With the rectified images, one can accurately determine the location and length of the target objects required for facility monitoring.