• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.5
• /
• pp.546-554
• /
• 2016

Free-viewpoint video (FVV) is a synthesization technology that generates a virtual viewpoint video using multiple videos recorded via wireless devices at heterogeneous locations. In order to introduce a new service that grafts the FVV onto the real-time streaming service using wireless devices, we need to overcome several constraints. Two main factors of those constraints are the limited wireless capacity that are shared fairly by multiple devices, and the transmission time constraint with which live streaming services have to comply. Therefore, for optimal quality of entire videos, a set of transmitting devices should be effectively selected depending on the condition of wireless channel and the required video popularity of specific viewpoint requested from users. For optimal selection, this study proposes a heuristic algorithm that takes into account the aforementioned factors from possible wireless transmission error behaviors and the requested viewpoint popularity. Through analysis and simulation, we show that with this algorithm, quality of most popular viewpoint videos is guaranteed. Furthermore, performance comparison against the existing scheme which is based only on the location of recording devices is made.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.7
• /
• pp.1804-1820
• /
• 1997

In this paper, an efficient call control procedure is presented for next generation wireless ATM networks and its performance is mathematically analyzed using the open queueing network. This procedure is based on a new scheme called as the cell clustering. When we use the cell clustering scheme, at the time that a mobile connection is admitted to the network, a virtual cell is constructed by choosing a group of neighboring base stations to which the call may probabilistically hand over and by assigning to the call a collection of virtual paths between the base stations. Within a microcell/picocell environment, it is seen that the cell clustering can support effectively a very high rate of handovers, provides very high system capacity, and guarantees a high degree of frequency reuse over the same geographical region without requiring the intervention of the network call control processor each time a handover occurs. But since mobiles, once admitted, are free to roam within the virtual cell, overload condition occurs in which the number of calls to be handled by one base station to exceed that cell site's capacity of radio channel. When an overload condition happens, the quality of service is abruptly degraded. We refer to this as the overload state and in order to quantify the degree of degradation we define two metrics, the probability of overload and the normalized average time spent in the overload state. By using the open network queueing model, we derive closed form expressions for the maximum number of calls that can be admitted into the virtual cell such that the two defined metrics are used as the acceptance criteria for call admission control.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.346-346
• /
• 2007

압전세라믹 재료는 현재 압전 변압기, actuator, transducer, sensor, speaker 등에 광범위하게 이용이 되고 있다. 이 중에서 압전세라믹 소결체를 이용한 스피커의 제조는 가공이 까다롭고, 대형의 크기로 제작 시 소자가 깨지는 등의 많은 제약을 받고 있으며, 저음 특성이 떨어져 응용 범위가 한정되어 있다. 따라서 최근에는 이러한 단점을 극복하기 위하여 세라믹/고분자 복합체를 이용한 필름 스피커를 제작하고자 시도하고 있다. 이러한 세라믹/고분자 0-3형 압전 복합체를 이용할 경우, 제품의 경량화를 실현할 수 있고, 크기나 환경의 영향을 거의 받지 않으므로, 고기능성 스피커로의 응용에 적합할 것으로 보인다. 따라서 본 연구에서는 PZT계의 세라믹와 PVDF, PVDF-TrFE, Polyester, acrylic resin 등의 여러 고분자 물질과의 복합체를 제조하여 압전특성을 평가하였다. 본 실험은 먼저 $(Pb_{1-a-b}Ba_aCd_b)(Zr_xTi_{1-x})_{1-c-d}(Ni_{1/3}Nb_{2/3})_c(Zn_{1/3}Nb_{2/3})_dO_3$ (이하 PZT라 표기)의 최적화 조성을 선택하여, $1050^{\circ}C$에서 소결된 분말을 48시간 ball milling방법 로 약 $1{\mu}m$ 크기로 분쇄하였다. 고분자 물질들은 알맞은 용제들을 선택하여 녹였다. 그 다음 소결된 PZT분말과 고분자를 50:50, 60:40, 65:35, 70:30등의 무게 분율로 혼합하고, 분산제, 소포제 등을 첨가하여 3단 roll mill을 이용하여 충분히 분산시켜 페이스트 (Paste)를 제조하였다. 제조된 페이스트를 ITO가 코팅된 PET필름 위에 스크린 프린팅 법을 사용하여 인쇄하여 $120^{\circ}C$에서 5분간 건조하였다. 코팅된 복합체의 두께는 약 $80{\mu}m$ 정도로 측정되었다. Ag 페이스트를 이용한 상부 전극 형성에도 스크린 프린팅 법을 적용하였다. 이를 $120^{\circ}C$에서 4 kV/mm의 DC 전계로 분극 공정을 수행한 후 전기적 특성을 평가하였다. 유전특성을 조사하기 위해서 LCR meter (EDC-1620)를 사용하였고, 시편의 결정구조는 XRD (Rigaku; D/MAX-2500H)을 통해 분석하였으며, 전자현미경(SEM)을 이용하여 미세구조를 분석하였다. 압전 전하상수$(d_{33})$ 값은 APC 8000 모델을 이용하여 측정하였다. PZT의 혼합비가 증가할수록 비유전율 및 압전 전하 상수 등의 전기적 특성이 증가되었다. 또 여러 고분자 물질 중에서 PVDF-TrFE 수지가 가장 우수한 특성을 보였다. 이는 PVDF-TrFE 수지가 압전성을 나타내기 때문인 것으로 판단되었다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.2
• /
• pp.163-174
• /
• 2020

Particulate matter levels are rapidly increasing daily, and this can affect human health. Therefore, air pollutant emissions from sea vessels require management. This study evaluates the status of air pollutants, focusing on air pollutant emissions from the vessels of the Korea Coast Guard (KCG), and proposes national management measures to reduce emissions. According to a report recently released (2018) by the National Institute of Environmental Research (NIER), emissions from vessels constituted 6.4 % of the total domestic emissions, including 13.1 % NO_x, 10.9 % SO_x, and 9.6 % particulate matter (PM10/PM2.5). Among the rates of pollutant emission from vessels, the emission rates of domestic and overseas cargo vessels were the highest (50.6 %); the ratio of fishing boats was 42.6 %. With respect to jurisdictional sea area, 44.1 % of the emissions are from the south sea, including the Busan and Ulsan ports, and 24.8 % of the emissions are from the west sea, including the Gwangyang and Yeosu ports. The KCG inspects boarding lines to manage emission conditions and regulate air pollutant emissions, but it takes time and effort to operate various discharge devices and measure fuel oil standards. In addition, owing to busy ship schedules, inspection documents are limited in terms of management. Therefore, to reduce the air pollutant emissions of such vessels, regulations will be strengthened to check for air pollutants, and a monitoring system based on actual field data using KCG patrol ships will be established, for each sea area, to manage the emissions of such vessels. Furthermore, there is a need for technological development and institutional support for the introduction of environmentally friendly vessels.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.855-858
• /
• 2006

First of all, Developing information technology makes it possible to change a paradigm of all kinds of areas, including an education. Students can choose learning goals and objects themselves and acquire not the accumulation of knowledge but the method of their learning. Moreover, Teachers get to be adviser, and students play a key role in teaming. That is, the subject of leaning is students. Constructivism emphasizes the student-oriented environment of education, which corresponds to the characteristics of hypeimedia. In addition, Internet allows us to make a practical plan for constructivism. Web Based Internet provides us with a proper environment to make constructivism practice md causes an education system to change. Sure Web Based Instruction makes them motivated to learn more, they can gain plenty of information regardless of places or time. Besides, they are able to consult more up-to-date information regarding their learning use hypermedia such as an image, audio, video, and test, and effectively communicate with their instructor through a board, an e-mail, a chatting etc. A school and instructors have been making effort to develop a new model of a teaching method to cope with a new environment change. In this thesis, with 'Design and Implementation of Web Based Instruction Based on Constructivism', providing online learner-oriented and indexed video lesson, learners can get chance of self-oriented learning. In addition, learners doesn't have to cover all contents of a lesson but can choose contents they want to have from a indexed list of a lesson, and they ran search contents they want to have with a 'Keyword Search' on a main page, which can make learners improve learner's achievement.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.223-231
• /
• 2018

Recently, due to various environmental problems, blast tracks in tunnel are replaced with concrete tracks, but they have more adverse effects on noise than blast tracks so that additional noise measures are needed. Among these measures, sound-absorbing blocks start to be used due to its easy and quick installation. However, the performance of sound absorption blocks need to be verified under real environmental and operational conditions. In this paper, interior noise levels in KTX train cruising in Dalseong tunnel are measured before and after the installation of sound-absorbing blocks and the measured data are analyzed and compared. Additionally, noise reduction are estimated by modeling the high speed train, the tunnel and absorption blocks. Measurement devices and methods are used according to ISO 3381 and the equivalent sound pressure levels during the cruising time inside the tunnel are computed. In addition to overall SPLs(Sound Pressure Levels), 1/3-octave-band levels are also analyzed to account for the frequency characteristics of sound absorption and equipment noise in a cabin. In addition, to consider the effects of train cruising speeds and environmental conditions on the measurements, the measured data are corrected by using those measured during the train-passing through the tunnels located before and behind the Dalseong tunnel. Analysis of measured results showed that the maximum noise reduction of 6.8 dB (A) can be achieved for the local region where the sound-absorbing blocks are installed. Finally, through the comparison of predicted 1/3-octave band SPLs for the KTX interior noise with the measurements, the understanding of noise reduction mechanism due to sound-absorbing blocks is enhanced.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.152-161
• /
• 2023

In general, large-capacity hydrogen storage vessels, typically in the form of vertical cylindrical vessels, are constructed using steel materials. These vessels are anchored to foundation slabs that are specially designed to suit the environmental conditions. This anchoring method involves pre-installed anchors on top of the concrete foundation slab. However, it's important to note that such a design can result in concentrated stresses at the anchoring points when external forces, such as seismic events, are at play. This may lead to potential structural damage due to anchor and concrete damage. For this reason, in this study, it selected an vertical hydrogen storage vessel based on site observations and created a 3D finite element model. Artificial seismic motions made following the procedures specified in ICC-ES AC 156, as well as domestic recorded earthquakes with a magnitude greater than 5.0, were applied to analyze the structural behavior and performance of the target structures. Conducting experiments on a structure built to actual scale would be ideal, but due to practical constraints, it proved challenging to execute. Therefore, it opted for an analytical approach to assess the safety of the target structure. Regarding the structural response characteristics, the acceleration induced by seismic motion was observed to amplify by approximately ten times compared to the input seismic motions. Additionally, there was a tendency for a decrease in amplification as the response acceleration was transmitted to the point where the centre of gravity is located. For the vulnerable components, specifically the sub-system (support columns and anchorages), the stress levels were found to satisfy the allowable stress criteria. However, the concrete's tensile strength exhibited only about a 5% margin of safety compared to the allowable stress. This indicates the need for mitigation strategies in addressing these concerns. Based on the research findings presented in this paper, it is anticipated that predictable load information for the design of storage vessels required for future shaking table tests will be provided.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.27-36
• /
• 2007

A recent study showed that MTBE can be degraded by Fenton's Reagent (FR). The treatment of MTBE with FR, however, has a definite limitation of extremely low pH requirement (optimum pH $3{\sim}4$) that makes the process impracticable under neutral pH condition on which the ferrous ion precipitate forming salt with hydroxyl anion, which result in the diminishment of the Fenton reaction and incompatible with biological treatment. Consequently, this process using only FR is not suitable for in-situ remediation of MTBE. In order to overcome this limitation, modified Fenton process using NTA, oxalate, and acetate as chelating reagents was introduced into this study. Modified Fenton reaction, available at near neutral pH, has been researched for the purpose of obtaining high performance of oxidation efficiency with stabilized ferrous or ferric ion by chelating agent. In the MTBE degradation experiment with modified Fenton reaction, it was observed that this reaction was influenced by some factors such as concentrations of ferric ion, hydrogen peroxide, and each chelating agent and pH. Six potential chelators including oxalate, succinate, acetate, citrate, NTA, and EDTA were tested to identify an appropriate chelator. Among them, oxalate, acetate, and NTA were selected based on their remediation efficiency and biodegradability of each chelator. Using NTA, the best result was obtained, showing more than 99.9% of MTBE degradation after 30 min at pH 7; the initial concentration of hydrogen peroxide, NTA, and ferric ion were 1470 mM, 6 mM, and 2 mM, respectively. Under the same experimental condition, the removal of MTBE using oxalate and acetate were 91.3% and 75.8%, respectively. Optimum concentration of iron ion were 3 mM using oxalate which showed the greatest removal efficiency. In case of acetate, $[MTBE]_0$ decreased gradually when concentration of iron ion increased above 5 mM. In this research, it was showed that modified Fenton reaction is proper for in-situ remediation of MTBE with great efficiency and the application of chelatimg agents, such as NTA, was able to make the ferric ion stable even at near neutral pH. In consequence, the outcomes of this study clearly showed that the modified Fenton process successfully coped with the limitation of the low pH requirement. Furthermore, the introduction of low molecular weight organic acids makes the process more available since these compounds have distinguishable biodegradability and it may be able to use natural iron mineral as catalyst for in situ remediation, so as to produce hydroxyl radical without the additional injection of ferric ion.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.24 no.3
• /
• pp.375-388
• /
• 2019

Accurate evaluation of sea-to-air $CO_2$ flux and its variability is crucial information to the understanding of global carbon cycle and the prediction of atmospheric $CO_2$ concentration. $fCO_2$ observations are sparse in space and time in the East Sea. In this study, we derived high resolution time series of surface $fCO_2$ values in the southwest East Sea, by feeding sea surface temperature (SST), salinity (SSS), chlorophyll-a (CHL), and mixed layer depth (MLD) values, from either satellite-observations or numerical model outputs, to three machine learning models. The root mean square error of the best performing model, a Random Forest (RF) model, was $7.1{\mu}atm$. Important parameters in predicting $fCO_2$ in the RF model were SST and SSS along with time information; CHL and MLD were much less important than the other parameters. The net $CO_2$ flux in the southwest East Sea, calculated from the $fCO_2$ predicted by the RF model, was $-0.76{\pm}1.15mol\;m^{-2}yr^{-1}$, close to the lower bound of the previous estimates in the range of $-0.66{\sim}-2.47mol\;m^{-2}yr^{-1}$. The time series of $fCO_2$ predicted by the RF model showed a significant variation even in a short time interval of a week. For accurate evaluation of the $CO_2$ flux in the Ulleung Basin, it is necessary to conduct high resolution in situ observations in spring when $fCO_2$ changes rapidly.

• Korean Journal of Plant Resources
• /
• v.21 no.1
• /
• pp.73-82
• /
• 2008

The resource plants of the Mt. Geonji was listed 354 taxa; 92 families, 242 genera, 303 species, 48 varieties and 3 forms. 354 taxa listed consists of 205 taxa of edible plants(57.1%),234 taxa of medicinal plants(65.2%), 167 taxa of ornamental plants(46.5%) and 218 taxa of the others(60.7%). Specific plant species by floral region were total 22 taxa; Trapella sinensis var. antennifera in class IV, Iris ensata var. spontanea in Class II, 16 taxa(Salix glandulosa, Alnus hirsuta, Chrysosplenium flagelliferum, Mallotus japonicus, Ilex macropoda, Grewia biloba var. parviflora, Vaccinium oldhami, Lysimachia barystachys, Fraxinus mandshurica, etc.) in class I. The naturalized plants in this site were 12 families, 23 genera, 28 species, 2 varieties, 30 taxa(Bromus unioloides, Phytolacca americana, Oenothera erythrosepala, Ipomoea hederacea var. hederacea, Aster pilosus, Erechtites hieracifolia) and naturalization rate was 8.5% of all 354 taxa vascular plants. Wild plants disturbing ecosystem like Solanum carolinense and Ambrosia artemisiifolia var. elatior have been increasing. So, it needs continuing control and conservation measures on the plant ecosystem.