• 한국세라믹학회지
• /
• 제39권7호
• /
• pp.693-698
• /
• 2002

반응소결 탄화규소의 잔류 실리콘 양을 최소화하기 위해 3성분계 탄화규소 분말을 혼합하여 최밀 충전 반음소결 탄화규소를 제조하였다. 기지상의 충전밀도 증가로 인해 반응소결 중 실리콘의 불완전 침윤이 발생하였으며, 이로 인한 잔류 기공은 조대 탄화규소 입자의 표면을 따라 존재함을 확인하였다. 불완전 침윤은 승온 중 분해되지 않고 남은 산화물이 실리콘의 용융 온도 이상에서 분해되어 생긴 고립기공에 의한 것으로 확인되었다. 기지상의 표면에 존재하리라 여겨지는 산화물을 제거하기 위해 침윤전 열처리 및 부식처리를 통해 완전침윤을 달성하였다.

• 한국세라믹학회지
• /
• 제32권11호
• /
• pp.1227-1232
• /
• 1995

Effect of heating rate on the microstructure of the silicon nitride ceramics has been investigated. The specimens with composition of 92Si3N4-6Y2O3-2Al2O3 (in wt%) were sintered at 176$0^{\circ}C$ under 127 kPa for 3h in N2 atmosphere at various heating rates from 1 to 10$0^{\circ}C$/min. The grain size of larger than 2${\mu}{\textrm}{m}$ and less than 1${\mu}{\textrm}{m}$ were measured and compared for the specimens. Regardless of heating rate, grain size of all the specimens showed bimodal distributions and the fracture toughness remained in the range of 5.53~5.72 MPa.m1/2. However, the aspect ratio of the grains of diameter above 2${\mu}{\textrm}{m}$ increased with the heating rate while their grain size and volume fraction decreased.

• 동력기계공학회지
• /
• 제11권1호
• /
• pp.56-62
• /
• 2007

This paper represents the cold energy for liquefied nitrogen gas and cascade refrigerator. In this study, the vaporizer of liquefied nitrogen gas has the fin coil tube type with the dimension of inside diameter of 10mm and outside diameter of 12mm. Also, the total length of vaporizer is 20,000mm. The main experimental parameters are the mean velocity in duct and the supplied flow-rates of liquefied nitrogen gas. For the cascade refrigeration system, the refrigerants are ethane(R 170) in the high pressure stage and R 22 in the low pressure stage.

• 한국연초학회지
• /
• 제8권1호
• /
• pp.41-48
• /
• 1986

This experiment was carries out to study on the effect of temperature raising rate to chemical composition of tobacco leaves during the midrib drying stage of flue-curing. The results were as follows : In the case of the temperature raising rate became more rapidly during midrib drying stage. It had a tendency to increase in oxailic acid, succinlc acid, ammonia, polyphenol; there was a large loss of total sugar, reducing sugar, malic acid, palmitic acid and linolenic acid; leaf color became more reddish; the leaf quality index value decreased, thereby the quality of external appearance deteriorated. It is desirable that the temperature raising rate had to be more slowly.

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.185-190
• /
• 2004

Plasma Display Panel is a display device emitting fluorescent light from gas discharge between a front and a rear panel sealed together. Front and rear panel have multitude of film layers and barrier ribs in the rear panel has the largest area so releasing various gases and affecting light emitting characteristics and lifetime. The remaining gases in a barrier rib were studied by thermal desorption analysis up to $400^{\circ}C$ and main gases were $H_2$ $H_2$O, CO. During sustaining at $300^{\circ}C$, the outgassing rates from other gases were decreased but$ H_2$ kept constantly increasing until 1 hour, which can be originated from the dissociation of organics remained in the inside of barrier rib material. In $H_2$O, two distinct peaks were observed: desorption from physically adsorbed one at $l00^{\circ}C$ and from chemically adsorbed one $400^{\circ}C$. The result can be utilized in interpretation of electronic and optical characteristics and evacuation process control of PDP

• 설비공학논문집
• /
• 제21권12호
• /
• pp.695-702
• /
• 2009

Dynamic behavior of Libr-water absorption system using low-temperature hot water was investigated numerically. Thermal-hydraulic model of single-effect/double-lift 100 RT chiller was developed by applying transient conservation equations of total mass, Libr mass, energy and momentum to each component. Transient variations of system properties and transport variables were analysed during start-up operation. Numerical analysis were performed to quantify the effects of bulk concentration and part-load operation on the system performance in terms of cooling capacity, coefficient of performance, and time constant of system. For an absorption chiller considered in the present study, optimum bulk concentration was found to exist, which resulted in the minimum time constant with stable cooling capacity. COP and time constant increased as the load decreased down to 40%, below which the time constant increased abruptly and COP decreased as the load decreased further.

• 대한방사선협회지
• /
• 제29권1호
• /
• pp.44-49
• /
• 2003

감마카메라를 이용하여 영상화할 수 있는 $^{99m}Tc-DMSA$ 신장 검사는 비침습적으로 신장의 기능과 형태를 동시에 평가할 수 있고, 신장 기능의 이상은 형태학적인 변화 보다 먼저 나타나기 때문에 다른 검사보다 $^{99m}Tc-DMSA$ 신장 검사를 이용하면 병변을 조기에 진단할 수 있는 장점이 있다. 신장의 상대적 기능 평가시에 깊이 보정, 총 계수 또는 평균 계수의 사용, BKG 보정, SPECT 검사의

• 한국진공학회지
• /
• 제8권2호
• /
• pp.111-115
• /
• 1999

The structural characteristics of an epitaxial $BaTiO_3$ film on MgO(001) grown by sputtering were studied as a function of temperature using in-situ, real time synchrotron x-ray scattering experiments. We found that the as-grown film was single c-domain but strained at room temperature and tetragonally distorted with the c-axis normal to the film surface. Interestingly, its lattice parameters were found to be expanded in both the in-plane and the out-of -plane directions, i.e. biaxially, comparing with those of a bulk $BaTiO_3$ . More importantly, as it was heated up to $600^{\circ}C$, the tetragonal structure was kept up through without and any phase transition, which is usually observed in other epitaxial ferroelectric thin films.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2231-2235
• /
• 2008

Thermal performance of fusing system in laser printer is determined by FPOT(First print out time) required and toner fusing quality. FPOT is influenced by the thermal resistance of fusing system between heat source and nip region. Also FPOT is depended by the heat source power and toner fusing temperature. The fusing quality of toner is decided by the temperature, pressure and duration time in nip region. In this study, I have performed thermal analysis for the toner fusing system. Computational simulation has been used to understand the effect of heat source power and printing speed etc. on the temperature distribution of the fusing system. Also in order to predict fusing quality, numerical simulation of the process that paper is continuously supplied to the nip regions were performed. In comparison with the experimental results of the fusing quality vs transferred calory to the toner layer, I could evaluate various fusing condition parameters effected on the thermal performance.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 하계학술발표대회
• /
• pp.89-89
• /
• 2005