• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.1
• /
• pp.73-80
• /
• 2022

Sensors are applied to small aviation platforms for various purposes. Radio frequency (RF) antennas, which are representative sensors, are available in many forms but require the application of slot array RF antennas to ensure high performance and designation. Slot RF array antennas are applied to dip brazing techniques, but the yield and production time are determined by the proficiency of production personnel in a labor-intensive form. Unmanned aerial vehicles or drones, which are representative small aviation platforms, are continuously exposed to various random vibrations because propellers and multiple power sources are used in them. In this study, the fatigue life of slot array RF antennas applied with additive manufacturing was evaluated through the cumulative damage method (Miner's rule) in a vibration environment with a small aviation platform. For the evaluation, an S N curve obtained from a fatigue strength test was used.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.105-111
• /
• 2019

In this paper, a performance analysis of waveguide broad-wall slot array antenna for millimeter-wave seeker in Ka-band was performed as using near-field measurement. The measurement of slot array antenna was conducted in both far-field and near-field. And the validation of near-field test in millimeter band was confirmed. It was confirmed that the beam pattern characteristics including beam width and side lobe level of the slot array antenna that performed the verification were the same. Differenced in the side lobe level of azimuth and elevation beam pattern were verified to be less than 1dB. Additionally, the new antenna aperture distribution was extracted as using back-projection method modifying the near-field data and then introduced the method conducting performance analysis of array antenna.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.1
• /
• pp.52-59
• /
• 1999

An experimental study on the grinding temperature, surface roughness and Acoustic Emission(AE) signals was conducted with different shapes of wheel. The grinding characteristics for slotted shapes of wheel changed by width and helical angle, were compared with those by general one. Lower grinding temperature was obtained for 30$^{\circ}$helical angle with 10mm width and Root Mean square(RMS) values of AE signals were lower for slotted shapes rather than general one. Surface roughness characteristics of slotted shapes found to be rough but the value of roughness for 45$^{\circ}$helical angel with 6mm width, represented to similar tendency general one.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.101-104
• /
• 1995

A acoustic emission (AE) sensor has been used to monitor tool were during milling process. The relation between tool wear and AE RMS (Root mean Square) signal was investigated experimentally. A avaliable monitoring index for monitoring toolwear was newly extracted form AE RMS. And on-line monitoring program was developed. The proposed monitoring system has verified experimentally by roughing end milling titanium alloy with TIN coated HSS tool.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.472-475
• /
• 2005

In this study, the equivalent physical properties of the shield-slot plate that has a lot of very tiny bridge shape structures on its plane were determined by tensile tests and structural analyses. With those results in hand, numerical analyses for the deflection profile by gravity effect were carried out to compare with experimental results. The two results were shown coincident very well so that the estimated equivalent physical properties were verified enough for further studies such as curvature reduction for the shield-slot plate.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.3
• /
• pp.23-28
• /
• 2006

The focus of this study is placed on the enhancement of flatness for the shielded slot plate, one of main components of the MCFC stack. The shielded slot plate is to get curvature during manufacturing process since it is produced by forming operation from only one side of it. Therefore, a correction die is proposed to place just after the main die to apply unbending on the curved plate to get almost flat product. In the design for the correction die, four kinds of design factors are selected to study which factor is the most influencing one affecting the flatness of the plate. From the experimental results using Taguchi method, it has been revealed that the Young's modulus of urethane die is the most critical factor.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.12
• /
• pp.1279-1284
• /
• 2012

Micro structures which are widely used at various fields are commonly fabricated by lithograph, etching and laser methods. Recently, with the emergence of micro tools and ultra-precision machine tools, fabrication of the micro structures obtained using end-milling are studied. However, there are some problems due to the diameter of the micro end-mill getting smaller below $100{\mu}m$. The micro run-out resulted from miniaturization of end-mills have influence seriously on accuracy of micro structures. The error of run-out with a tooling jig showed a decrease of about $9.3{\mu}m$. Furthermore, micro structures with width of $30{\mu}m$ could be applied through experiments of slot machining obtained using 30 and $50{\mu}m$ end-mill. Also, narrow angle structures with $30^{\circ}$ angle could be applied through analysis of machining acute angle structures. Based on basic experiments, micro fluidics channels and spiral patterns for air bearing were machined.

• Transactions of Materials Processing
• /
• v.21 no.6
• /
• pp.341-347
• /
• 2012

The metallic bipolar plates of the molten carbonate fuel cell(MCFC) are composed of shielded slot plates and a center-plate. The shielded slot plates support the center-plate and the membrane electrode assembly. Compressive forces are applied to the shielded slot plate in order to increase the contact area between shielded slot plates and the membrane electrode assembly (MEA). In the design of the shielded slot plate, it is necessary to predict the mechanical behavior of the shielded slot plate. The shielded slot plates are manufactured by a three-stage forming process consisting of slitting, preforming and the final forming process. The mechanical behavior of the shielded slot plate is largely affected by the forming process. In this study, the simulation of the three-stage forming process was used to predict the mechanical behavior of the shielded slot plate. The present simulation approach showed good agreements with the experimental results.

• Transactions of Materials Processing
• /
• v.21 no.5
• /
• pp.298-304
• /
• 2012

The shielded slot plates for a molten carbonate fuel cell(MCFC) have a sheared corrugated trapezoidal pattern. In the FEM simulations for the production of the shielded slot plate, the user material subroutine VUMAT in the commercial FEM software ABAQUS was used to implement a ductile fracture criterion. The critical damage value for the ductile fracture criterion was determined by comparing the experimental results of the shearing process with the simulation results. Using the ductile fracture criterion, the FEM simulation of the three-dimensional forming process of the shielded slot plate was conducted. The effects of the shearing process on the forming process were examined through FEM simulation and experiments. The forming simulation of nine unit cells was conducted. Using the simulation results of the forming process, the deformed shape after springback was calculated. The experimental result shows good agreement with the simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.832-836
• /
• 1997

An experimental study on the grinding temperature, surface roughness and Acoustic Emission(AE) signal was conducted with different shapes of wheel. The grinding characteristics by slotted shapes of wheel changed by width and helical angle,were compared with those by general one. Lower grinding temperature was obtained for 30 .deg. helical angel with 10mm width and Root Mean Square(RMS) values of AE signals were lower for slotted shapes rather than general one. Surface roughness characteristic of slotted shapes found to be rough,but the value of roughness for 45 .deg. helical angel with 6mm width, represented to similar tendency general one.