• Proceedings of the Membrane Society of Korea Conference
• /
• 1994.10a
• /
• pp.68-68
• /
• 1994

현재의 도금폐수처리는 침전옹집법에 의해 슬러지화 하여 매립되고 있으나, 이 매립물은 침출수를 방출하여 수질오염에 문제가 되고 있다. 특히 크롬폐수는 환원 침전시키고 있으나, 공기에 의한 산화로 재용출 가능성이 비교적 높다. 따라서 크롬 고금폐수를 역삼투압법에 의해 크롬이온을 농축 회수하고, 생성되는 투과수는 도금공정에 재투입하여 공해물질이 발생되지 않는 무배출 공정 (Zero-Discharge System)을 개발하는데 본 연구의 목적이 있다. 본 실험에서는 유가금속 중 크롬을 회수하기 위하여 크롬 모델폐수의 농도, pH등을 변화시키면서 연속공정으로 R.O. Cell에 의한 투과수와 막의 상태 변화등을 살펴보았으며, 크롬 실폐수를 R.O. Cell 테스트와 역삼투기기 (1-2ton/day)를 이용하여 농축수 및 투과수의 재이용에 관하여 실험하였다.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.14 no.4
• /
• pp.151-160
• /
• 2006

Anaerobic treatment of landfill leachate was studied to investigate the behaviors of pollutant and the characteristics of microorganism for 10 months. The upflow anaerobic sludge blanket (UASB) reactor achieved about 90% chemical oxygen demand (COD) removal at organic loading rates(OLR) up to $20kgCOD/m^3.d$. At higher OLR ($8-20kgCOD/m^3.d$), the propionate concentration increased, indicating that converting propionate to acetate was the rate-limiting step. Nevertheless, increase in the precipitate inside and on the surface of granules as well as on the wall of the reactor resulted in operational problems. The main inorganic precipitate in the granule was calcium compound. Although specific methanogenic activity (SMA) was not affected seriously in this study, metals had to be removed prior to anaerobic treatment so as to be free from the excessive inorganic accumulation that resulted in operational problems.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.3
• /
• pp.475-484
• /
• 2000

The purpose of this study was to develop model for estimating biodegrability of organic sludge (sewage and papermill) in various environmental conditions. to assume degradable degree with operating time of SRB reactor. and evaluate duratior of organic sludge as carbon source. Average TCOD was 28.7~63.2mg/L in effluent. organic sludge did not much supply carbon source for experimental period. But in point of durability. it seemed that organic sludge was efficient because it was not consumed by degradation of much organic matter within short period. With increasing $SO_4{^{2-}}$ reduction rate. Pb and Fe was removed 77~82% and 33~59%. respectively. Because Al was precipitated as a hydroxide. its removal rate wa,. about $54{\pm}2%$ in R-l~R-3 maintaining low pH but about 78% in R-4 maintaining high pH. Because Mn was large in solubility. it showed to be much lower than other heavy metals. Considering supportable capacity or durability of orgainc matter for initial SRB mixing ratio of sewage/papermill 0.5 was regarded as appropriate substituting material and at this time. it estimated that carbon source continued about 3.08 year but safety factor must apply to be thought over. because various factors had an effect on degradation of organic sludge.

• Journal of Korea Water Resources Association
• /
• v.47 no.5
• /
• pp.483-490
• /
• 2014

The design procedures for a biological reactor and a secondary settling tank (SST) of an activated sludge system are based on the steady state design method (Ekama et al., 1986; WRC, 1984) and the 1-D flux theory design method (Ekama et al., 1997), respectively. This study combined both of the design procedures, to determine the optimum sludge concentration in the reactor and the best design with the lowest cost. The best design of the reactor volume and the SST diameter at the optimum sludge concentration were specified with varying wastewater and sludge characteristics, temperature, sludge retention time (SRT) and peak flow rate. The effects of the influent wastewater characteristics, such as substrate concentration and unbiodegradable particulate fraction, were found to be considerable, but the effect of unbiodegradable soluble fraction was to be negligible. The effects of sludge settling characteristics, were also significant. SRT, as an operating parameter, was found to be an important factor for determining the optimum sludge concentration. However, the effect of temperature was found to be small. Furthermore, for designing a large scale wastewater treatment plant, the number of reactors or SSTs could be estimated, by dividing the total reactor volume or SST area. The new combined design procedure, proposed in this research, will be able to allow engineers to provide the best design of an activated sludge system with the lowest cost.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.842-846
• /
• 2008

원수의 탁질 중에서 입경이 $10^{-1}$mm이상인 것은 보통침전으로 제거가 가능하지만, 입경이��$10^{-3}mm$이하가 되면 일반적으로 콜로이드입자라고 총칭하며 그대로의 상태로서는 거의 침강되지 않을 뿐만 아니라 급속여과기구에서도 포착되지 않는다. 따라서 급속여과 방식에서는 이와 같은 탁질을 효과적으로 제거하기 위한 전처리로서 응집조작으로 인한 콜로이드상의 탁질을 플록화하여 약품침전이나 급속여과에서 포착되도록 탁질의 성상을 변화시키는 조작이 반드시 필요하다. 또한 양호한 플록을 효과적으로 형성시키는 약품혼화와 플록형성 등을 강구해야 한다. 이에 본 연구에서는 현재 국내에서 운영하고 있는 정수처리시스템의 일부인 혼화지내에 혼화지점의 단면적을 축소시켜 약품혼화효과를 극대화하고 혼화기의 소요동력을 감소시켜 혼화효과를 개선하며 혼화지내 혼화기 운용의 비용 절감 효과를 증가시키기 위한 저에너지형 CF혼화장치를 개발하는데 연구 목적이 있다. 연구결과 CF혼화장치의 설치시 약품 투입 위치에 따라 $2{\sim}6%$정도의 탁도제거율의 상승과 슬러지 높이의 차이를 보이는 것으로 나타났으며 이 실험 결과 약품투입장소에서 혼화지의 Compact화로 인해 급속 혼화를 이룰 경우 더 많은 플록화로 인해 탁도 제거율이 높아지는 것을 알 수 있다.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.4
• /
• pp.303-311
• /
• 2007

The consumption of artificially crushed sands exceeds more than 30 percent of the domestic sand supply in South Korea, and its rate is still increasing. For the manufacture of crushed sand granites and granitic gneisses are preferred, fine fractions (i.e. sludge, particles finer than 63 microns) are removed by use of flocculation agents, and its amount occupy about 15 wt%. The sludges consist of quartz, feldspars, micas, chlorite/vermiculite, kaolinites, smectites and occasionally calcite. Among the clay minerals micas are usually predominant, and $14{\AA}$ minerals, kaolinites and smectites are rather scarce. Jurassic granites usually contain more kaolinites and smectites than those of Cretaceous to Tertiary granites, probably due to longer geologic ages. On the other hand, sludge from Precambrian gneiss does not contain kaolinites and smectites. Chemical analyses for the granites and their sludges show rather clear differences in most of major chemical components. Except for $SiO_2,\;Na_2O\;and\;K_2O$, all other components represent rather clear increase. Decrease of $SiO_2$ content is attributed to the relative decrease of quartz in the sludges. And the $Na_2O decrease is caused by a relatively stronger weathering property of albite compared to Ca plagioclase. The $K_2O$ content shows rather small differences throughout the whole samples. The increases of $Al_2O_3$ and other major components resulted from weathering processes and most of colored components are also concentrated in the sludges. Particle size analyses reveal that the sludges are categorized as sandy loams in a sand-silt-clay triangular diagram. The sludge is now classified as industrial waste because of its impermeability, and this result was also confirmed by rather higher hydraulic conductivities. For the environmental problems, and accomplishing effective sand manufacture, more fresh rocks with little weathering products must be chosen.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.2
• /
• pp.168-174
• /
• 2008

Diagnosis on setteability based on human operator's experimental knowledge, which could be established by long term operation, is a limit factor to construction of automation control system in wastewater treatment plant. On-line SVI(Sludge Volume Index) analyzer was developed which can measure SV30 automatically by image capture and image analysis method. In this paper, information got by settling process was studied using On-line SVI analyzer for better operation & management of WWTPs. First, SV30 detection algorithm was developed using image capture and image analysis for settling test and it showed that automatic detection is feasible even if deflocculation and bulking was occurred. Second, turbidity assessment model was developed using image analysis.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.197-197
• /
• 2019

총인처리시설에서는 응집제를 주입하여 인이나 오염물질을 침전시켜 처리하고 있으며 PAC(poly aluminum chloride)나 $FeCl_3$, $Al_2(SO_4)_3$, 등 다양한 종류의 응집제가 사용되어지고 있다. 하지만 기존에 사용되어 지고 있는 알루미늄계열의 응집제는 처리수에 잔류이온이 존재하게 되어 인체에 축적돼 알츠하이머 병 등 신체질환을 유발할 수 있는 단점이 있다. 따라서 이러한 단점을 사전에 예방하기 위해 $TiCl_4$와 같은 티타늄계열 응집제에 대한 연구가 진행되고 있다. $TiCl_4$ 응집제는 인 제거에 효과적으로 적용할 수 있으며 수중에 잔류이온을 유발하지 않으며 Ti이온은 치과임플란트나 의료장비로 사용될 만큼 인체에 무해하다고 알려져 있다. 응집제 사용에 따라 생성된 응집슬러지의 처리방안에 있어서 기존 응집제의 경우 생성된 슬러지의 대부분은 하수슬러지 위탁처리업체를 통해 소각 및 매립, 재활용 되고 있으나, $TiCl_4$를 응집제로 사용할 경우 생성된 슬러지를 인발하여 건조 및 소성을 통해 이산화티타늄으로 재활용할 수 있어 슬러지를 친환경적으로 처리가 가능해 기존 슬러지 처리방안의 경제적, 환경적 부담을 줄일 수 있는 장점이 있다. 따라서 본 연구에서는 $TiCl_4$를 하수처리장 방류수에 주입하여 수중의 총인(T-P)을 처리한 후 생성된 슬러지를 인발하여 건조와 소성과정을 거쳐 이산화티타늄을 제조하였다. 방류수를 취수해 2.5mg/L의 초기 총인 농도를 가진 원수를 제조하였으며 제조된 원수에 $TiCl_4$를 0.6mL 주입하였을 때 99.93%의 총인제거효율을 얻을 수 있었다. 응집 실험 후 생성된 슬러지를 인발하여 건조 후 $300{\sim}1000^{\circ}C$의 각각 다른 온도조건에서 소성하여 이산화티타늄을 제조하였으며, SEM과 XRD를 통해 제조된 이산화티타늄의 표면특성과 결정성 분석을 실시하였다. 제조된 이산화티타늄은 $500{\sim}800^{\circ}C$에서는 아나타제, $900{\sim}1000^{\circ}C$에서는 루타일 결정구조가 나타났다. 또한, $TiCl_4$ 주입량에 따른 이산화티타늄의 최종 생산량과 제조 시 사용되는 건조로 및 소성로의 경제적 비용 등을 고려하여 이산화티타늄 1Ton을 제조하기 위해 필요한 단가를 산출하였다. 본 연구에서 제조된 이산화티타늄 1kg의 생산단가는 약 5,400원으로 나타났으며, 가장 많이 사용되는 P-25 광촉매 보다 저렴한 가격으로 제조 및 판매를 기대할 수 있다. 따라서 하수처리장에 적용 시 기존 응집제 보다 비싼 $TiCl_4$ 비용을 보완하고 친환경적인 슬러지 처리로 제조된 이산화티타늄의 유통 및 현장적용을 통해 경제적, 환경적으로 우수하다고 판단된다.

• Economic and Environmental Geology
• /
• v.38 no.3 s.172
• /
• pp.273-284
• /
• 2005

Coagulation and precipitation process by using lime$(Ca(OH)_2)$ and calcium carbonate $(CaCO_3)$ were applied to remove heavy metals from groundwater in laboratory scale. From results of batch tests, by the addition of $0.3\;wt.\%$ lime, more than $90\%$ of As and Mn were removed and $70-80\%$ of Cd and Zn were removed by using $0.5\;wt.\%$ of lime. Removal efficiency of Pb almost reached $100\%$ with only $0.1\;wt.\%$ of calcium carbonate and more than $93\%$ of Cd were removed by the addition of $0.1\;wt.\%$of calcium carbonate. Pilot scale column experiments were performed to remove heavy metals in the separation process of precipitated Hoc to supernatant after the coagulation/ precipitation. For lime as a coagulant, more than $99\%$of As were removed from artificial groundwater and removal efficiencies of Cd, Mn, and Zn were over $80\%$. By using calcium carbonate, more than $95\%$ of Cd and Pb were removed in column experiment. Fe and Mn contaminated groundwater taken from a real landfill site, Ulsan was used for the column experiment and more than $99\%$ of Fe and Mn were removed by the addition of $1\;wt.\%$ lime in column experiment, suggesting that the coagulation/precipitation process by using lime and calcium carbonate have a great possibility to remove heavy metals from contaminated groundwater.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.3 no.2
• /
• pp.37-45
• /
• 1995

The performance and the operational problems of UASB(Upflow Anaerobic Sludge Blanket) reactor for treatment of dairy wastewaters were investigated. Synthetic milk wastewater was successfully treated up to the loading rate of 3.9kg $COD/m^3.day$, with a specific gas production rate of 1. 23 I/I. day and a COD removal efficiency of over 90%. However, the sludge rising was observed at the loading rate of 2.1kg $COD/m^3.day$, due probably to the formation of scum layer at the surface of settling compartment. The BMP(biochemical methane potential) of raw milk wastewater and ice cream wastewater, measured by using SBT(serum bottle test), were 0.135 and 0.66ml $CH_4/mg\;COD_{added}$, respectively. The sludge activity increased more than 8 times from 0.159g $COD-CH_4/g$ VSS. d during 90 days of operation.